diff --git a/Bootloaders/CDC/BootloaderCDC.txt b/Bootloaders/CDC/BootloaderCDC.txt
index 276a0c9c46..618b95d257 100644
--- a/Bootloaders/CDC/BootloaderCDC.txt
+++ b/Bootloaders/CDC/BootloaderCDC.txt
@@ -47,9 +47,9 @@
  *  This bootloader enumerates to the host as a CDC Class device (virtual serial port), allowing for AVR109
  *  protocol compatible programming software to load firmware onto the AVR.
  *
- *  Out of the box this bootloader builds for the AT90USBUSB1287, and will fit into 4KB of bootloader space.
- *  If you wish to enlarge this space and/or change the AVR model, you will need to edit the MCU, FLASH_SIZE_KB
- *  and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
+ *  Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
+ *  into 4KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to
+ *  edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
  *
  *  When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
  *  bootloader from the normal user application.
diff --git a/Bootloaders/CDC/makefile b/Bootloaders/CDC/makefile
index 066fb8884d..a92172d543 100644
--- a/Bootloaders/CDC/makefile
+++ b/Bootloaders/CDC/makefile
@@ -95,7 +95,7 @@ F_USB = $(F_CPU)
 # Note that the bootloader size and start address given in AVRStudio is in words and not
 # bytes, and so will need to be doubled to obtain the byte address needed by AVR-GCC.
 FLASH_SIZE_KB        = 128
-BOOT_SECTION_SIZE_KB = 4
+BOOT_SECTION_SIZE_KB = 8
 
 
 # Formulas used to calculate the starting address of the Bootloader section, and the User Application
diff --git a/Bootloaders/DFU/BootloaderDFU.txt b/Bootloaders/DFU/BootloaderDFU.txt
index e10beea36d..2c9eaf1de5 100644
--- a/Bootloaders/DFU/BootloaderDFU.txt
+++ b/Bootloaders/DFU/BootloaderDFU.txt
@@ -47,9 +47,9 @@
  *  This bootloader enumerates to the host as a DFU Class device, allowing for DFU-compatible programming
  *  software to load firmware onto the AVR.
  *
- *  Out of the box this bootloader builds for the AT90USBUSB1287, and will fit into 4KB of bootloader space.
- *  If you wish to enlarge this space and/or change the AVR model, you will need to edit the MCU, FLASH_SIZE_KB
- *  and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
+ *  Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
+ *  into 4KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to
+ *  edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
  *
  *  When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
  *  bootloader from the normal user application.
diff --git a/Bootloaders/DFU/makefile b/Bootloaders/DFU/makefile
index 608564ebe7..f78ceb270e 100644
--- a/Bootloaders/DFU/makefile
+++ b/Bootloaders/DFU/makefile
@@ -95,7 +95,7 @@ F_USB = $(F_CPU)
 # Note that the bootloader size and start address given in AVRStudio is in words and not
 # bytes, and so will need to be doubled to obtain the byte address needed by AVR-GCC.
 FLASH_SIZE_KB        = 128
-BOOT_SECTION_SIZE_KB = 4
+BOOT_SECTION_SIZE_KB = 8
 
 
 # Formulas used to calculate the starting address of the Bootloader section, and the User Application
diff --git a/Bootloaders/HID/BootloaderHID.txt b/Bootloaders/HID/BootloaderHID.txt
index d32efeeb71..f6c084d65f 100644
--- a/Bootloaders/HID/BootloaderHID.txt
+++ b/Bootloaders/HID/BootloaderHID.txt
@@ -51,10 +51,10 @@
  *  from PJRC (used with permission). This bootloader is deliberatley non-compatible with the properietary PJRC
  *  HalfKay bootloader GUI; only the command line interface software accompanying this bootloader will work with it.
  *  
- *  Out of the box this bootloader builds for the AT90USB1287, and will fit into 2KB of bootloader space for the
- *  Series 2 USB AVRs (ATMEGAxxU2, AT90USBxx2) or 4KB of bootloader space for all other models. If you wish to
- *  enlarge this space and/or change the AVR model, you will need to edit the MCU, FLASH_SIZE_KB and
- *  BOOT_SECTION_SIZE_KB values in the accompanying makefile.
+ *  Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
+ *  into 2KB of bootloader space for the Series 2 USB AVRs (ATMEGAxxU2, AT90USBxx2) or 4KB of bootloader space for
+ *  all other models. If you wish to alter this size and/or change the AVR model, you will need to edit the MCU,
+ *  FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
  *
  *  \section Sec_Installation Driver Installation
  *
diff --git a/Bootloaders/HID/makefile b/Bootloaders/HID/makefile
index efbb6a645b..bfefbf6954 100644
--- a/Bootloaders/HID/makefile
+++ b/Bootloaders/HID/makefile
@@ -95,7 +95,7 @@ F_USB = $(F_CPU)
 # Note that the bootloader size and start address given in AVRStudio is in words and not
 # bytes, and so will need to be doubled to obtain the byte address needed by AVR-GCC.
 FLASH_SIZE_KB        = 128
-BOOT_SECTION_SIZE_KB = 4
+BOOT_SECTION_SIZE_KB = 8
 
 
 # Formulas used to calculate the starting address of the Bootloader section. These formulas