Merge pull request #1498 from That-Canadian/minidox

Minidox

keyboards/minidox/i2c.h

@@ -16,7 +16,7 @@
 #define SLAVE_BUFFER_SIZE 0x10
 
 // i2c SCL clock frequency
-#define SCL_CLOCK  100000L
+#define SCL_CLOCK  400000L
 
 extern volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
 
@@ -28,4 +28,22 @@ uint8_t i2c_master_read(int);
 void i2c_reset_state(void);
 void i2c_slave_init(uint8_t address);
 
+
+static inline unsigned char i2c_start_read(unsigned char addr) {
+  return i2c_master_start((addr << 1) | I2C_READ);
+}
+
+static inline unsigned char i2c_start_write(unsigned char addr) {
+  return i2c_master_start((addr << 1) | I2C_WRITE);
+}
+
+// from SSD1306 scrips
+extern unsigned char i2c_rep_start(unsigned char addr);
+extern void i2c_start_wait(unsigned char addr);
+extern unsigned char i2c_readAck(void);
+extern unsigned char i2c_readNak(void);
+extern unsigned char i2c_read(unsigned char ack);
+
+#define i2c_read(ack)  (ack) ? i2c_readAck() : i2c_readNak();
+
 #endif

keyboards/minidox/keymaps/that_canadian/config.h

@@ -25,6 +25,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define USE_SERIAL
 
+#define EE_HANDS
+
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D7
 #define RGBLIGHT_TIMER

keyboards/minidox/keymaps/that_canadian/keymap.c

@@ -40,7 +40,11 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * |   Z  |   X  |   C  |   V  |   B  |           |   N  |   M  |   ,  |   .  |   /  |
  * `----------------------------------'           `----------------------------------'
  *                  ,--------------------.    ,------,-------------.
+<<<<<<< HEAD
+ *                  | Shift| LOWER|      |    |      | RAISE| Ctrl |
+=======
  *                  | Ctrl | LOWER|      |    |      | RAISE| Shift|
+>>>>>>> a4958a532da154b9dd6f6144836a73f9de641f74
  *                  `-------------| Space|    |BckSpc|------+------.
  *                                |      |    |      |
  *                                `------'    `------'
@@ -49,7 +53,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,         KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    \
   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,         KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, \
   KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,         KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, \
-                    KC_LCTL, LOWER, KC_SPC,         KC_BSPC, RAISE, OSM(MOD_LSFT)                 \
+                    OSM(MOD_LSFT), LOWER, KC_SPC,         KC_BSPC, RAISE, KC_LCTL                 \
 ),
 
 /* Raise

keyboards/minidox/matrix.c

@@ -226,9 +226,7 @@ uint8_t matrix_scan(void)
         TXLED0;
         error_count = 0;
     }
-
     matrix_scan_quantum();
-
     return ret;
 }
 

keyboards/minidox/readme.md

@@ -1,5 +1,5 @@
-ECO
-===
+MiniDox
+=====
 
 ![MimiDox](http://i.imgur.com/iWb3yO0.jpg)
 
@@ -13,3 +13,63 @@ Make example for this keyboard (after setting up your build environment):
     make minidox-rev1-default
 
 See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+
+## Build Guide
+
+A build guide for putting together the MiniDox v1 can be found here: [MiniDox Build Log / Guide](http://imgur.com/a/vImo6)
+
+Flashing
+-------
+Note: Most of this is copied from the Let's Split readme, because it is awesome
+
+From the keymap directory run `make SUBPROJECT-KEYMAP-avrdude` for automatic serial port resolution and flashing.
+Example: `make rev1-default-avrdude`
+
+Choosing which board to plug the USB cable into (choosing Master)
+--------
+Because the two boards are identical, the firmware has logic to differentiate the left and right board.
+
+It uses two strategies to figure things out: look at the EEPROM (memory on the chip) or looks if the current board has the usb cable.
+
+The EEPROM approach requires additional setup (flashing the eeeprom) but allows you to swap the usb cable to either side.
+
+The USB cable approach is easier to setup and if you just want the usb cable on the left board, you do not need to do anything extra.
+
+### Setting the left hand as master
+If you always plug the usb cable into the left board, nothing extra is needed as this is the default. Comment out `EE_HANDS` and comment out `I2C_MASTER_RIGHT` or `MASTER_RIGHT` if for some reason it was set.
+
+### Setting the right hand as master
+If you always plug the usb cable into the right board, add an extra flag to your `config.h`
+```
+ #define MASTER_RIGHT
+```
+
+### Setting EE_hands to use either hands as master
+If you define `EE_HANDS` in your `config.h`, you will need to set the
+EEPROM for the left and right halves.
+
+The EEPROM is used to store whether the
+half is left handed or right handed. This makes it so that the same firmware
+file will run on both hands instead of having to flash left and right handed
+versions of the firmware to each half. To flash the EEPROM file for the left
+half run:
+```
+avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-lefthand.eep
+// or the equivalent in dfu-programmer
+
+```
+and similarly for right half
+```
+avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-righhand.eep
+// or the equivalent in dfu-programmer
+```
+
+NOTE: replace `$(COM_PORT)` with the port of your device (e.g. `/dev/ttyACM0`)
+
+After you have flashed the EEPROM, you then need to set `EE_HANDS` in your config.h, rebuild the hex files and reflash.
+
+Note that you need to program both halves, but you have the option of using
+different keymaps for each half. You could program the left half with a QWERTY
+layout and the right half with a Colemak layout using bootmagic's default layout option.
+Then if you connect the left half to a computer by USB the keyboard will use QWERTY and Colemak when the
+right half is connected.

keyboards/minidox/rev1/config.h

@@ -30,7 +30,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define USE_SERIAL
 
-// #define EE_HANDS
+//#define EE_HANDS
 
 #define I2C_MASTER_LEFT
 //#define I2C_MASTER_RIGHT

keyboards/minidox/split_util.c

@@ -21,7 +21,8 @@ static void setup_handedness(void) {
   #ifdef EE_HANDS
     isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
   #else
-    #ifdef I2C_MASTER_RIGHT
+    // I2C_MASTER_RIGHT is deprecated, use MASTER_RIGHT instead, since this works for both serial and i2c
+    #if defined(I2C_MASTER_RIGHT) || defined(MASTER_RIGHT)
       isLeftHand = !has_usb();
     #else
       isLeftHand = has_usb();
@@ -32,6 +33,9 @@ static void setup_handedness(void) {
 static void keyboard_master_setup(void) {
 #ifdef USE_I2C
     i2c_master_init();
+#ifdef SSD1306OLED
+    matrix_master_OLED_init ();
+#endif
 #else
     serial_master_init();
 #endif

keyboards/minidox/split_util.h

@@ -19,4 +19,6 @@ void split_keyboard_setup(void);
 bool has_usb(void);
 void keyboard_slave_loop(void);
 
+void matrix_master_OLED_init (void);
+
 #endif