skullY
7 years ago
committed by
Jack Humbert
parent
9b879b1267
commit
9d1a08e38a
@ -0,0 +1,238 @@
|
||||
## PS/2 Mouse Support
|
||||
|
||||
Its possible to hook up a PS/2 mouse (for example touchpads or trackpoints) to your keyboard as a composite device.
|
||||
|
||||
To hook up a Trackpoint, you need to obtain a Trackpoint module (i.e. harvest from a Thinkpad keyboard), identify the function of each pin of the module, and make the necessary circuitry between controller and Trackpoint module. For more information, please refer to [Trackpoint Hardware](https://deskthority.net/wiki/TrackPoint_Hardware) page on Deskthority Wiki.
|
||||
|
||||
There are three available modes for hooking up PS/2 devices: USART (best), interrupts (better) or busywait (not recommended).
|
||||
|
||||
### Busywait version
|
||||
|
||||
Note: This is not recommended, you may encounter jerky movement or unsent inputs. Please use interrupt or USART version if possible.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_BUSYWAIT = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_BUSYWAIT
|
||||
# define PS2_CLOCK_PORT PORTD
|
||||
# define PS2_CLOCK_PIN PIND
|
||||
# define PS2_CLOCK_DDR DDRD
|
||||
# define PS2_CLOCK_BIT 1
|
||||
# define PS2_DATA_PORT PORTD
|
||||
# define PS2_DATA_PIN PIND
|
||||
# define PS2_DATA_DDR DDRD
|
||||
# define PS2_DATA_BIT 2
|
||||
#endif
|
||||
```
|
||||
|
||||
### Interrupt version
|
||||
|
||||
The following example uses D2 for clock and D5 for data. You can use any INT or PCINT pin for clock, and any pin for data.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_INT = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_INT
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 2
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 5
|
||||
|
||||
#define PS2_INT_INIT() do { \
|
||||
EICRA |= ((1<<ISC21) | \
|
||||
(0<<ISC20)); \
|
||||
} while (0)
|
||||
#define PS2_INT_ON() do { \
|
||||
EIMSK |= (1<<INT2); \
|
||||
} while (0)
|
||||
#define PS2_INT_OFF() do { \
|
||||
EIMSK &= ~(1<<INT2); \
|
||||
} while (0)
|
||||
#define PS2_INT_VECT INT2_vect
|
||||
#endif
|
||||
```
|
||||
|
||||
### USART version
|
||||
|
||||
To use USART on the ATMega32u4, you have to use PD5 for clock and PD2 for data. If one of those are unavailable, you need to use interrupt version.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_USART = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_USART
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 2
|
||||
|
||||
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
|
||||
/* set DDR of CLOCK as input to be slave */
|
||||
#define PS2_USART_INIT() do { \
|
||||
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
|
||||
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
|
||||
UCSR1C = ((1 << UMSEL10) | \
|
||||
(3 << UPM10) | \
|
||||
(0 << USBS1) | \
|
||||
(3 << UCSZ10) | \
|
||||
(0 << UCPOL1)); \
|
||||
UCSR1A = 0; \
|
||||
UBRR1H = 0; \
|
||||
UBRR1L = 0; \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_INT_ON() do { \
|
||||
UCSR1B = ((1 << RXCIE1) | \
|
||||
(1 << RXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_POLL_ON() do { \
|
||||
UCSR1B = (1 << RXEN1); \
|
||||
} while (0)
|
||||
#define PS2_USART_OFF() do { \
|
||||
UCSR1C = 0; \
|
||||
UCSR1B &= ~((1 << RXEN1) | \
|
||||
(1 << TXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
|
||||
#define PS2_USART_RX_DATA UDR1
|
||||
#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
|
||||
#define PS2_USART_RX_VECT USART1_RX_vect
|
||||
#endif
|
||||
```
|
||||
|
||||
### Additional Settings
|
||||
|
||||
#### PS/2 mouse features
|
||||
|
||||
These enable settings supported by the PS/2 mouse protocol: http://www.computer-engineering.org/ps2mouse/
|
||||
|
||||
```
|
||||
/* Use remote mode instead of the default stream mode (see link) */
|
||||
#define PS2_MOUSE_USE_REMOTE_MODE
|
||||
|
||||
/* Enable the scrollwheel or scroll gesture on your mouse or touchpad */
|
||||
#define PS2_MOUSE_ENABLE_SCROLLING
|
||||
|
||||
/* Some mice will need a scroll mask to be configured. The default is 0xFF. */
|
||||
#define PS2_MOUSE_SCROLL_MASK 0x0F
|
||||
|
||||
/* Applies a transformation to the movement before sending to the host (see link) */
|
||||
#define PS2_MOUSE_USE_2_1_SCALING
|
||||
|
||||
/* The time to wait after initializing the ps2 host */
|
||||
#define PS2_MOUSE_INIT_DELAY 1000 /* Default */
|
||||
```
|
||||
|
||||
You can also call the following functions from ps2_mouse.h
|
||||
|
||||
```
|
||||
void ps2_mouse_disable_data_reporting(void);
|
||||
|
||||
void ps2_mouse_enable_data_reporting(void);
|
||||
|
||||
void ps2_mouse_set_remote_mode(void);
|
||||
|
||||
void ps2_mouse_set_stream_mode(void);
|
||||
|
||||
void ps2_mouse_set_scaling_2_1(void);
|
||||
|
||||
void ps2_mouse_set_scaling_1_1(void);
|
||||
|
||||
void ps2_mouse_set_resolution(ps2_mouse_resolution_t resolution);
|
||||
|
||||
void ps2_mouse_set_sample_rate(ps2_mouse_sample_rate_t sample_rate);
|
||||
```
|
||||
|
||||
#### Fine control
|
||||
|
||||
Use the following defines to change the sensitivity and speed of the mouse.
|
||||
Note: you can also use `ps2_mouse_set_resolution` for the same effect (not supported on most touchpads).
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_X_MULTIPLIER 3
|
||||
#define PS2_MOUSE_Y_MULTIPLIER 3
|
||||
#define PS2_MOUSE_V_MULTIPLIER 1
|
||||
```
|
||||
|
||||
#### Scroll button
|
||||
|
||||
If you're using a trackpoint, you will likely want to be able to use it for scrolling.
|
||||
Its possible to enable a "scroll button/s" that when pressed will cause the mouse to scroll instead of moving.
|
||||
To enable the feature, you must set a scroll button mask as follows:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_MASK (1<<PS2_MOUSE_BUTTON_MIDDLE) /* Default */
|
||||
```
|
||||
|
||||
To disable the scroll button feature:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_MASK 0
|
||||
```
|
||||
|
||||
The available buttons are:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_BTN_LEFT 0
|
||||
#define PS2_MOUSE_BTN_RIGHT 1
|
||||
#define PS2_MOUSE_BTN_MIDDLE 2
|
||||
```
|
||||
|
||||
You can also combine buttons in the mask by `|`ing them together.
|
||||
|
||||
Once you've configured your scroll button mask, you must configure the scroll button send interval.
|
||||
This is the interval before which if the scroll buttons were released they would be sent to the host.
|
||||
After this interval, they will cause the mouse to scroll and will not be sent.
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_SEND 300 /* Default */
|
||||
```
|
||||
|
||||
To disable sending the scroll buttons:
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_SEND 0
|
||||
```
|
||||
|
||||
Fine control over the scrolling is supported with the following defines:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_DIVISOR_H 2
|
||||
#define PS2_MOUSE_SCROLL_DIVISOR_V 2
|
||||
```
|
||||
|
||||
#### Debug settings
|
||||
|
||||
To debug the mouse, add `debug_mouse = true` or enable via bootmagic.
|
||||
|
||||
```
|
||||
/* To debug the mouse reports */
|
||||
#define PS2_MOUSE_DEBUG_HID
|
||||
#define PS2_MOUSE_DEBUG_RAW
|
||||
```
|
||||
@ -1,403 +0,0 @@
|
||||
|
||||
## Audio output from a speaker
|
||||
|
||||
Your keyboard can make sounds! If you've got a Planck, Preonic, or basically any AVR keyboard that allows access to the C6 or B5 port (`#define C6_AUDIO` and/or `#define B5_AUDIO`), you can hook up a simple speaker and make it beep. You can use those beeps to indicate layer transitions, modifiers, special keys, or just to play some funky 8bit tunes.
|
||||
|
||||
If you add `AUDIO_ENABLE = yes` to your `rules.mk`, there's a couple different sounds that will automatically be enabled without any other configuration:
|
||||
|
||||
```
|
||||
STARTUP_SONG // plays when the keyboard starts up (audio.c)
|
||||
GOODBYE_SONG // plays when you press the RESET key (quantum.c)
|
||||
AG_NORM_SONG // plays when you press AG_NORM (quantum.c)
|
||||
AG_SWAP_SONG // plays when you press AG_SWAP (quantum.c)
|
||||
MUSIC_ON_SONG // plays when music mode is activated (process_music.c)
|
||||
MUSIC_OFF_SONG // plays when music mode is deactivated (process_music.c)
|
||||
CHROMATIC_SONG // plays when the chromatic music mode is selected (process_music.c)
|
||||
GUITAR_SONG // plays when the guitar music mode is selected (process_music.c)
|
||||
VIOLIN_SONG // plays when the violin music mode is selected (process_music.c)
|
||||
MAJOR_SONG // plays when the major music mode is selected (process_music.c)
|
||||
```
|
||||
|
||||
You can override the default songs by doing something like this in your `config.h`:
|
||||
|
||||
```c
|
||||
#ifdef AUDIO_ENABLE
|
||||
#define STARTUP_SONG SONG(STARTUP_SOUND)
|
||||
#endif
|
||||
```
|
||||
|
||||
A full list of sounds can be found in [quantum/audio/song_list.h](https://github.com/qmk/qmk_firmware/blob/master/quantum/audio/song_list.h) - feel free to add your own to this list! All available notes can be seen in [quantum/audio/musical_notes.h](https://github.com/qmk/qmk_firmware/blob/master/quantum/audio/musical_notes.h).
|
||||
|
||||
To play a custom sound at a particular time, you can define a song like this (near the top of the file):
|
||||
|
||||
```c
|
||||
float my_song[][2] = SONG(QWERTY_SOUND);
|
||||
```
|
||||
|
||||
And then play your song like this:
|
||||
|
||||
```c
|
||||
PLAY_SONG(my_song);
|
||||
```
|
||||
|
||||
Alternatively, you can play it in a loop like this:
|
||||
|
||||
```c
|
||||
PLAY_LOOP(my_song);
|
||||
```
|
||||
|
||||
It's advised that you wrap all audio features in `#ifdef AUDIO_ENABLE` / `#endif` to avoid causing problems when audio isn't built into the keyboard.
|
||||
|
||||
## Music mode
|
||||
|
||||
The music mode maps your columns to a chromatic scale, and your rows to octaves. This works best with ortholinear keyboards, but can be made to work with others. All keycodes less than `0xFF` get blocked, so you won't type while playing notes - if you have special keys/mods, those will still work. A work-around for this is to jump to a different layer with KC_NOs before (or after) enabling music mode.
|
||||
|
||||
Recording is experimental due to some memory issues - if you experience some weird behavior, unplugging/replugging your keyboard will fix things.
|
||||
|
||||
Keycodes available:
|
||||
|
||||
* `MU_ON` - Turn music mode on
|
||||
* `MU_OFF` - Turn music mode off
|
||||
* `MU_TOG` - Toggle music mode
|
||||
* `MU_MOD` - Cycle through the music modes:
|
||||
* `CHROMATIC_MODE` - Chromatic scale, row changes the octave
|
||||
* `GUITAR_MODE` - Chromatic scale, but the row changes the string (+5 st)
|
||||
* `VIOLIN_MODE` - Chromatic scale, but the row changes the string (+7 st)
|
||||
* `MAJOR_MODE` - Major scale
|
||||
|
||||
In music mode, the following keycodes work differently, and don't pass through:
|
||||
|
||||
* `LCTL` - start a recording
|
||||
* `LALT` - stop recording/stop playing
|
||||
* `LGUI` - play recording
|
||||
* `KC_UP` - speed-up playback
|
||||
* `KC_DOWN` - slow-down playback
|
||||
|
||||
By default, `MUSIC_MASK` is set to `keycode < 0xFF` which means keycodes less than `0xFF` are turned into notes, and don't output anything. You can change this by defining this in your `config.h` like this:
|
||||
|
||||
#define MUSIC_MASK keycode != KC_NO
|
||||
|
||||
Which will capture all keycodes - be careful, this will get you stuck in music mode until you restart your keyboard!
|
||||
|
||||
The pitch standard (`PITCH_STANDARD_A`) is 440.0f by default - to change this, add something like this to your `config.h`:
|
||||
|
||||
#define PITCH_STANDARD_A 432.0f
|
||||
|
||||
## MIDI functionalty
|
||||
|
||||
This is still a WIP, but check out `quantum/keymap_midi.c` to see what's happening. Enable from the Makefile.
|
||||
|
||||
## Bluetooth functionality
|
||||
|
||||
This requires [some hardware changes](https://www.reddit.com/r/MechanicalKeyboards/comments/3psx0q/the_planck_keyboard_with_bluetooth_guide_and/?ref=search_posts), but can be enabled via the Makefile. The firmware will still output characters via USB, so be aware of this when charging via a computer. It would make sense to have a switch on the Bluefruit to turn it off at will.
|
||||
|
||||
## RGB Under Glow Mod
|
||||
|
||||
|
||||
|
||||
Here is a quick demo on Youtube (with NPKC KC60) (https://www.youtube.com/watch?v=VKrpPAHlisY).
|
||||
|
||||
For this mod, you need an unused pin wiring to DI of WS2812 strip. After wiring the VCC, GND, and DI, you can enable the underglow in your Makefile.
|
||||
|
||||
RGBLIGHT_ENABLE = yes
|
||||
|
||||
In order to use the underglow animation functions, you need to have `#define RGBLIGHT_ANIMATIONS` in your `config.h`.
|
||||
|
||||
Please add the following options into your config.h, and set them up according your hardware configuration. These settings are for the `F4` pin by default:
|
||||
|
||||
#define RGB_DI_PIN F4 // The pin your RGB strip is wired to
|
||||
#define RGBLIGHT_ANIMATIONS // Require for fancier stuff (not compatible with audio)
|
||||
#define RGBLED_NUM 14 // Number of LEDs
|
||||
#define RGBLIGHT_HUE_STEP 10
|
||||
#define RGBLIGHT_SAT_STEP 17
|
||||
#define RGBLIGHT_VAL_STEP 17
|
||||
|
||||
You'll need to edit `RGB_DI_PIN` to the pin you have your `DI` on your RGB strip wired to.
|
||||
|
||||
The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. For details, please check this keymap. `keyboards/planck/keymaps/yang/keymap.c`
|
||||
|
||||
### WS2812 Wiring
|
||||
|
||||
|
||||
|
||||
Please note the USB port can only supply a limited amount of power to the keyboard (500mA by standard, however, modern computer and most usb hubs can provide 700+mA.). According to the data of NeoPixel from Adafruit, 30 WS2812 LEDs require a 5V 1A power supply, LEDs used in this mod should not more than 20.
|
||||
|
||||
## PS/2 Mouse Support
|
||||
|
||||
Its possible to hook up a PS/2 mouse (for example touchpads or trackpoints) to your keyboard as a composite device.
|
||||
|
||||
To hook up a Trackpoint, you need to obtain a Trackpoint module (i.e. harvest from a Thinkpad keyboard), identify the function of each pin of the module, and make the necessary circuitry between controller and Trackpoint module. For more information, please refer to [Trackpoint Hardware](https://deskthority.net/wiki/TrackPoint_Hardware) page on Deskthority Wiki.
|
||||
|
||||
There are three available modes for hooking up PS/2 devices: USART (best), interrupts (better) or busywait (not recommended).
|
||||
|
||||
### Busywait version
|
||||
|
||||
Note: This is not recommended, you may encounter jerky movement or unsent inputs. Please use interrupt or USART version if possible.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_BUSYWAIT = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_BUSYWAIT
|
||||
# define PS2_CLOCK_PORT PORTD
|
||||
# define PS2_CLOCK_PIN PIND
|
||||
# define PS2_CLOCK_DDR DDRD
|
||||
# define PS2_CLOCK_BIT 1
|
||||
# define PS2_DATA_PORT PORTD
|
||||
# define PS2_DATA_PIN PIND
|
||||
# define PS2_DATA_DDR DDRD
|
||||
# define PS2_DATA_BIT 2
|
||||
#endif
|
||||
```
|
||||
|
||||
### Interrupt version
|
||||
|
||||
The following example uses D2 for clock and D5 for data. You can use any INT or PCINT pin for clock, and any pin for data.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_INT = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_INT
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 2
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 5
|
||||
|
||||
#define PS2_INT_INIT() do { \
|
||||
EICRA |= ((1<<ISC21) | \
|
||||
(0<<ISC20)); \
|
||||
} while (0)
|
||||
#define PS2_INT_ON() do { \
|
||||
EIMSK |= (1<<INT2); \
|
||||
} while (0)
|
||||
#define PS2_INT_OFF() do { \
|
||||
EIMSK &= ~(1<<INT2); \
|
||||
} while (0)
|
||||
#define PS2_INT_VECT INT2_vect
|
||||
#endif
|
||||
```
|
||||
|
||||
### USART version
|
||||
|
||||
To use USART on the ATMega32u4, you have to use PD5 for clock and PD2 for data. If one of those are unavailable, you need to use interrupt version.
|
||||
|
||||
In rules.mk:
|
||||
|
||||
```
|
||||
PS2_MOUSE_ENABLE = yes
|
||||
PS2_USE_USART = yes
|
||||
```
|
||||
|
||||
In your keyboard config.h:
|
||||
|
||||
```
|
||||
#ifdef PS2_USE_USART
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 2
|
||||
|
||||
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
|
||||
/* set DDR of CLOCK as input to be slave */
|
||||
#define PS2_USART_INIT() do { \
|
||||
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
|
||||
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
|
||||
UCSR1C = ((1 << UMSEL10) | \
|
||||
(3 << UPM10) | \
|
||||
(0 << USBS1) | \
|
||||
(3 << UCSZ10) | \
|
||||
(0 << UCPOL1)); \
|
||||
UCSR1A = 0; \
|
||||
UBRR1H = 0; \
|
||||
UBRR1L = 0; \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_INT_ON() do { \
|
||||
UCSR1B = ((1 << RXCIE1) | \
|
||||
(1 << RXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_POLL_ON() do { \
|
||||
UCSR1B = (1 << RXEN1); \
|
||||
} while (0)
|
||||
#define PS2_USART_OFF() do { \
|
||||
UCSR1C = 0; \
|
||||
UCSR1B &= ~((1 << RXEN1) | \
|
||||
(1 << TXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
|
||||
#define PS2_USART_RX_DATA UDR1
|
||||
#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
|
||||
#define PS2_USART_RX_VECT USART1_RX_vect
|
||||
#endif
|
||||
```
|
||||
|
||||
### Additional Settings
|
||||
|
||||
#### PS/2 mouse features
|
||||
|
||||
These enable settings supported by the PS/2 mouse protocol: http://www.computer-engineering.org/ps2mouse/
|
||||
|
||||
```
|
||||
/* Use remote mode instead of the default stream mode (see link) */
|
||||
#define PS2_MOUSE_USE_REMOTE_MODE
|
||||
|
||||
/* Enable the scrollwheel or scroll gesture on your mouse or touchpad */
|
||||
#define PS2_MOUSE_ENABLE_SCROLLING
|
||||
|
||||
/* Some mice will need a scroll mask to be configured. The default is 0xFF. */
|
||||
#define PS2_MOUSE_SCROLL_MASK 0x0F
|
||||
|
||||
/* Applies a transformation to the movement before sending to the host (see link) */
|
||||
#define PS2_MOUSE_USE_2_1_SCALING
|
||||
|
||||
/* The time to wait after initializing the ps2 host */
|
||||
#define PS2_MOUSE_INIT_DELAY 1000 /* Default */
|
||||
```
|
||||
|
||||
You can also call the following functions from ps2_mouse.h
|
||||
|
||||
```
|
||||
void ps2_mouse_disable_data_reporting(void);
|
||||
|
||||
void ps2_mouse_enable_data_reporting(void);
|
||||
|
||||
void ps2_mouse_set_remote_mode(void);
|
||||
|
||||
void ps2_mouse_set_stream_mode(void);
|
||||
|
||||
void ps2_mouse_set_scaling_2_1(void);
|
||||
|
||||
void ps2_mouse_set_scaling_1_1(void);
|
||||
|
||||
void ps2_mouse_set_resolution(ps2_mouse_resolution_t resolution);
|
||||
|
||||
void ps2_mouse_set_sample_rate(ps2_mouse_sample_rate_t sample_rate);
|
||||
```
|
||||
|
||||
#### Fine control
|
||||
|
||||
Use the following defines to change the sensitivity and speed of the mouse.
|
||||
Note: you can also use `ps2_mouse_set_resolution` for the same effect (not supported on most touchpads).
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_X_MULTIPLIER 3
|
||||
#define PS2_MOUSE_Y_MULTIPLIER 3
|
||||
#define PS2_MOUSE_V_MULTIPLIER 1
|
||||
```
|
||||
|
||||
#### Scroll button
|
||||
|
||||
If you're using a trackpoint, you will likely want to be able to use it for scrolling.
|
||||
Its possible to enable a "scroll button/s" that when pressed will cause the mouse to scroll instead of moving.
|
||||
To enable the feature, you must set a scroll button mask as follows:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_MASK (1<<PS2_MOUSE_BUTTON_MIDDLE) /* Default */
|
||||
```
|
||||
|
||||
To disable the scroll button feature:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_MASK 0
|
||||
```
|
||||
|
||||
The available buttons are:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_BTN_LEFT 0
|
||||
#define PS2_MOUSE_BTN_RIGHT 1
|
||||
#define PS2_MOUSE_BTN_MIDDLE 2
|
||||
```
|
||||
|
||||
You can also combine buttons in the mask by `|`ing them together.
|
||||
|
||||
Once you've configured your scroll button mask, you must configure the scroll button send interval.
|
||||
This is the interval before which if the scroll buttons were released they would be sent to the host.
|
||||
After this interval, they will cause the mouse to scroll and will not be sent.
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_SEND 300 /* Default */
|
||||
```
|
||||
|
||||
To disable sending the scroll buttons:
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_BTN_SEND 0
|
||||
```
|
||||
|
||||
Fine control over the scrolling is supported with the following defines:
|
||||
|
||||
```
|
||||
#define PS2_MOUSE_SCROLL_DIVISOR_H 2
|
||||
#define PS2_MOUSE_SCROLL_DIVISOR_V 2
|
||||
```
|
||||
|
||||
#### Debug settings
|
||||
|
||||
To debug the mouse, add `debug_mouse = true` or enable via bootmagic.
|
||||
|
||||
```
|
||||
/* To debug the mouse reports */
|
||||
#define PS2_MOUSE_DEBUG_HID
|
||||
#define PS2_MOUSE_DEBUG_RAW
|
||||
```
|
||||
|
||||
## Safety Considerations
|
||||
|
||||
You probably don't want to "brick" your keyboard, making it impossible
|
||||
to rewrite firmware onto it. Here are some of the parameters to show
|
||||
what things are (and likely aren't) too risky.
|
||||
|
||||
- If your keyboard map does not include RESET, then, to get into DFU
|
||||
mode, you will need to press the reset button on the PCB, which
|
||||
requires unscrewing the bottom.
|
||||
- Messing with tmk_core / common files might make the keyboard
|
||||
inoperable
|
||||
- Too large a .hex file is trouble; `make dfu` will erase the block,
|
||||
test the size (oops, wrong order!), which errors out, failing to
|
||||
flash the keyboard, leaving it in DFU mode.
|
||||
- To this end, note that the maximum .hex file size on Planck is
|
||||
7000h (28672 decimal)
|
||||
|
||||
```
|
||||
Linking: .build/planck_rev4_cbbrowne.elf [OK]
|
||||
Creating load file for Flash: .build/planck_rev4_cbbrowne.hex [OK]
|
||||
|
||||
Size after:
|
||||
text data bss dec hex filename
|
||||
0 22396 0 22396 577c planck_rev4_cbbrowne.hex
|
||||
```
|
||||
|
||||
- The above file is of size 22396/577ch, which is less than
|
||||
28672/7000h
|
||||
- As long as you have a suitable alternative .hex file around, you
|
||||
can retry, loading that one
|
||||
- Some of the options you might specify in your keyboard's Makefile
|
||||
consume extra memory; watch out for BOOTMAGIC_ENABLE,
|
||||
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, CONSOLE_ENABLE, API_SYSEX_ENABLE
|
||||
- DFU tools do /not/ allow you to write into the bootloader (unless
|
||||
you throw in extra fruitsalad of options), so there is little risk
|
||||
there.
|
||||
- EEPROM has around a 100000 write cycle. You shouldn't rewrite the
|
||||
firmware repeatedly and continually; that'll burn the EEPROM
|
||||
eventually.
|
||||
|
||||
Loading…
Reference in new issue