Add support for the cluecard

pull/616/head^2
skullY 8 years ago
parent d561f63bd1
commit adad05c3fb

@ -0,0 +1,76 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870)
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= yes # Audio output on port C6
ifndef QUANTUM_DIR
include ../../Makefile
endif

@ -0,0 +1,98 @@
#include "cluecard.h"
#define BL_RED OCR1B
#define BL_GREEN OCR1A
#define BL_BLUE OCR1C
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
}
void matrix_scan_kb(void) {
// put your looping keyboard code here
// runs every cycle (a lot)
matrix_scan_user();
}
bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
// put your per-action keyboard code here
// runs for every action, just before processing by the firmware
return process_record_user(keycode, record);
}
void led_set_kb(uint8_t usb_led) {
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
led_set_user(usb_led);
}
void backlight_init_ports(void)
{
// Set B5, B6, and B7 as output
DDRB |= (1<<7)|(1<<6)|(1<<5);
// Setup PWM
ICR1 = 0xFFFF;
TCCR1A = 0b10101010;
TCCR1B = 0b00011001;
BL_RED = 0xFFFF;
BL_GREEN = 0xFFFF;
BL_BLUE = 0xFFFF;
}
void backlight_set(uint8_t level)
{
// Set the RGB color
switch (level)
{
case 0:
// Off
BL_RED = 0xFFFF;
BL_GREEN = 0xFFFF;
BL_BLUE = 0xFFFF;
break;
case 1:
// Red
BL_RED = 0x0000;
BL_GREEN = 0xFFFF;
BL_BLUE = 0xFFFF;
break;
case 2:
// Green
BL_RED = 0xFFFF;
BL_GREEN = 0x0000;
BL_BLUE = 0xFFFF;
break;
case 3:
// Blue
BL_RED = 0xFFFF;
BL_GREEN = 0xFFFF;
BL_BLUE = 0x0000;
break;
case 4:
// Magenta
BL_RED = 0x4000;
BL_GREEN = 0x4000;
BL_BLUE = 0x4000;
break;
case 5:
// Purple
BL_RED = 0x0000;
BL_GREEN = 0xFFFF;
BL_BLUE = 0x0000;
break;
case 6:
// Yellow
BL_RED = 0x0000;
BL_GREEN = 0x0000;
BL_BLUE = 0xFFFF;
break;
default:
xprintf("Unknown level: %d\n", level);
}
}

@ -0,0 +1,22 @@
#ifndef CLUECARD_H
#define CLUECARD_H
#include "quantum.h"
// This a shortcut to help you visually see your layout.
// The first section contains all of the arguements
// The second converts the arguments into a two-dimensional array
#define KEYMAP( \
k00, k01, k02, \
k10, k12, \
k20, k21, k22, \
k11, \
k30, k31, k32 \
) { \
{ k00, k01, k02, }, \
{ k10, k11, k12, }, \
{ k20, k21, k22, }, \
{ k30, k31, k32, } \
}
#endif

@ -0,0 +1,167 @@
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xC1ED
#define PRODUCT_ID 0x2330
#define DEVICE_VER 0x0001
#define MANUFACTURER Clueboard
#define PRODUCT ATMEGA32U4 Firmware Dev Kit
#define DESCRIPTION A small board to help you hack on QMK.
/* key matrix size */
#define MATRIX_ROWS 4
#define MATRIX_COLS 3
/*
* Keyboard Matrix Assignments
*
* Change this to how you wired your keyboard
* COLS: AVR pins used for columns, left to right
* ROWS: AVR pins used for rows, top to bottom
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
*
*/
#define MATRIX_ROW_PINS { F0, F5, F4, B4 }
#define MATRIX_COL_PINS { F1, F7, F6 }
#define UNUSED_PINS
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION ROW2COL
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCING_DELAY 20
/* define if matrix has ghost (lacks anti-ghosting diodes) */
//#define MATRIX_HAS_GHOST
/* number of backlight levels */
#define BACKLIGHT_LEVELS 6
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
//#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
//#define LOCKING_RESYNC_ENABLE
/*
* Force NKRO
*
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
* makefile for this to work.)
*
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
* until the next keyboard reset.
*
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is
* fully operational during normal computer usage.
*
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
* bootmagic, NKRO mode will always be enabled until it is toggled again during a
* power-up.
*
*/
//#define FORCE_NKRO
/*
* Magic Key Options
*
* Magic keys are hotkey commands that allow control over firmware functions of
* the keyboard. They are best used in combination with the HID Listen program,
* found here: https://www.pjrc.com/teensy/hid_listen.html
*
* The options below allow the magic key functionality to be changed. This is
* useful if your keyboard/keypad is missing keys and you want magic key support.
*
*/
/* key combination for magic key command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* control how magic key switches layers */
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
/* override magic key keymap */
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
//#define MAGIC_KEY_HELP1 H
//#define MAGIC_KEY_HELP2 SLASH
//#define MAGIC_KEY_DEBUG D
//#define MAGIC_KEY_DEBUG_MATRIX X
//#define MAGIC_KEY_DEBUG_KBD K
//#define MAGIC_KEY_DEBUG_MOUSE M
//#define MAGIC_KEY_VERSION V
//#define MAGIC_KEY_STATUS S
//#define MAGIC_KEY_CONSOLE C
//#define MAGIC_KEY_LAYER0_ALT1 ESC
//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
//#define MAGIC_KEY_LAYER0 0
//#define MAGIC_KEY_LAYER1 1
//#define MAGIC_KEY_LAYER2 2
//#define MAGIC_KEY_LAYER3 3
//#define MAGIC_KEY_LAYER4 4
//#define MAGIC_KEY_LAYER5 5
//#define MAGIC_KEY_LAYER6 6
//#define MAGIC_KEY_LAYER7 7
//#define MAGIC_KEY_LAYER8 8
//#define MAGIC_KEY_LAYER9 9
//#define MAGIC_KEY_BOOTLOADER PAUSE
//#define MAGIC_KEY_LOCK CAPS
//#define MAGIC_KEY_EEPROM E
//#define MAGIC_KEY_NKRO N
//#define MAGIC_KEY_SLEEP_LED Z
/* Underlight configuration
*/
#define RGB_DI_PIN E6
//#define RGBLIGHT_TIMER
#define RGBLED_NUM 4 // Number of LEDs
#define RGBLIGHT_HUE_STEP 10
#define RGBLIGHT_SAT_STEP 17
#define RGBLIGHT_VAL_STEP 17
/*
* Feature disable options
* These options are also useful to firmware size reduction.
*/
/* disable debug print */
//#define NO_DEBUG
/* disable print */
//#define NO_PRINT
/* disable action features */
//#define NO_ACTION_LAYER
//#define NO_ACTION_TAPPING
//#define NO_ACTION_ONESHOT
//#define NO_ACTION_MACRO
//#define NO_ACTION_FUNCTION
#endif

@ -0,0 +1,21 @@
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = no # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = yes # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
ifndef QUANTUM_DIR
include ../../../../Makefile
endif

@ -0,0 +1,8 @@
#ifndef CONFIG_USER_H
#define CONFIG_USER_H
#include "../../config.h"
// place overrides here
#endif

@ -0,0 +1,63 @@
#include "cluecard.h"
#ifdef AUDIO_ENABLE
#include "audio.h"
#endif
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[0] = KEYMAP(
RGB_TOG, RGB_SAI, RGB_VAI, \
RGB_HUD, RGB_HUI, \
RGB_MOD, RGB_SAD, RGB_VAD, \
BL_STEP, \
F(0), F(1), F(2) \
)
};
#ifdef AUDIO_ENABLE
float tone_startup[][2] = SONG(STARTUP_SOUND);
float tone_qwerty[][2] = SONG(QWERTY_SOUND);
float tone_dvorak[][2] = SONG(DVORAK_SOUND);
float tone_colemak[][2] = SONG(COLEMAK_SOUND);
float tone_plover[][2] = SONG(PLOVER_SOUND);
float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND);
float music_scale[][2] = SONG(MUSIC_SCALE_SOUND);
float tone_goodbye[][2] = SONG(GOODBYE_SOUND);
#endif
const uint16_t PROGMEM fn_actions[] = {
[0] = ACTION_FUNCTION(0),
[1] = ACTION_FUNCTION(1),
[2] = ACTION_FUNCTION(2)
};
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
if (record->event.pressed) {
switch (id) {
case 0:
PLAY_NOTE_ARRAY(tone_startup, false, 0);
break;
case 1:
PLAY_NOTE_ARRAY(music_scale, false, 0);
break;
case 2:
PLAY_NOTE_ARRAY(tone_goodbye, false, 0);
break;
}
}
};
void matrix_init_user(void) {
}
void matrix_scan_user(void) {
}
bool process_record_user(uint16_t keycode, keyrecord_t *record) {
return true;
}
void led_set_user(uint8_t usb_led) {
}

@ -0,0 +1 @@
# The default keymap for cluecard

@ -0,0 +1,28 @@
cluecard keyboard firmware
======================
## Quantum MK Firmware
For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
## Building
Download or clone the whole firmware and navigate to the keyboards/cluecard folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
Depending on which keymap you would like to use, you will have to compile slightly differently.
### Default
To build with the default keymap, simply run `make`.
### Other Keymaps
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
```
$ make keymap=[default|jack|<name>]
```
Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
Loading…
Cancel
Save