Keyboard: add tokyo60 (#2861)

* adding tokyo60 to qmk

* updating readme

* updating keymap and power consumption for mobile
pull/3751/head
Alvin C 6 years ago committed by Drashna Jaelre
parent 26dacd51fc
commit b806cc9eea

@ -0,0 +1,66 @@
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x6060
#define DEVICE_VER 0x0001
#define MANUFACTURER Tokyo Keyboard
#define PRODUCT tokyo60
#define DESCRIPTION q.m.k. keyboard firmware for tokyo60
/* key matrix size */
#define MATRIX_ROWS 5
#define MATRIX_COLS 14
/* number of backlight levels */
#define BACKLIGHT_PIN B7
#ifdef BACKLIGHT_PIN
#define BACKLIGHT_LEVELS 6
//#define BACKLIGHT_ON_STATE 1
#endif
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION ROW2COL
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCING_DELAY 5
/* Set power consumption to work with mobile devices */
#define USB_MAX_POWER_CONSUMPTION 100
/* key combination for command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* key matrix pins */
#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B2, B5, B4, D7, D6, B3 }
#define UNUSED_PINS
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/* prevent stuck modifiers */
#define PREVENT_STUCK_MODIFIERS
#define RGB_DI_PIN F7
#ifdef RGB_DI_PIN
#define RGBLIGHT_ANIMATIONS
#define RGBLED_NUM 10
#define RGBLIGHT_HUE_STEP 12
#define RGBLIGHT_SAT_STEP 12
#define RGBLIGHT_VAL_STEP 12
#endif
/* For Production */
#define QMK_ESC_OUTPUT F0 // usually COL
#define QMK_ESC_INPUT D0 // usually ROW
#endif

@ -0,0 +1 @@
#include "../../config.h"

@ -0,0 +1,56 @@
#include "tokyo60.h"
/*
* Default HHKB Layout
*/
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
/* 0: Default layer
Esc 1 2 3 4 5 6 7 8 9 0 - = \ `
Tab Q W E R T Y U I O P [ ] BkSpc
Ctrl A S D F G H J K L Fn3 ' Enter
Shift Z X C V B N M , . / Shift Fn
Gui Alt Space Alt Gui
*/
TOKYO_KEYMAP(
KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \
KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_FN0, \
KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT ),
/* 1: HHKB Fn layer
Pwr F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Ins Del
Caps RGB RGBfwRGBrvBLtogBLstp Psc Slk Pus Up
VoD VoU Mut Ejc NP_* NP_/ Home PgUp Left RightNPEnt
NP_+ NP_- End PgDwnDown
*/
TOKYO_KEYMAP(
KC_PWR, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \
KC_CAPS, RGB_TOG, RGB_MOD, RGB_RMOD, BL_TOGG, BL_STEP, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_TRNS, \
KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_EJCT, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_PENT, \
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, \
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS ),
};
/*5
* Fn action definition
*/
const uint16_t PROGMEM fn_actions[] = {
[0] = ACTION_LAYER_MOMENTARY(1),
};
void matrix_scan_user(void) {
};

@ -0,0 +1,15 @@
# tokyo60
![tokyo60](http://tokyokeyboard.com/wp-content/uploads/2018/02/AI7B4543_copy_page_20180215141449-1200x800.jpg)
Minimal hacker style mechanical keyboard designed in Tokyo. Full aluminum hi-pro construction with integrated top-plate. Cherry MX compatible. [More Info at Tokyo Keyboard](http://tokyokeyboard.com).
Keyboard Maintainer: [tokyo keyboard](http://tokyokeyboard.com)
Hardware Supported: tokyo60 rev1
Hardware Availability: [tokyo keyboard](http://tokyokeyboard.com), [Massdrop](https://www.massdrop.com/buy/massdrop-x-tokyo-keyboard-tokyo60-keyboard-kit?mode=guest_open)
Make example for this keyboard (after setting up your build environment):
make tokyo60:default
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

@ -0,0 +1,75 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
MIDI_ENABLE = no # MIDI controls
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
RGBLIGHT_ENABLE = yes # Enable RGB light

@ -0,0 +1,19 @@
#include "tokyo60.h"
//#include "led.h"
void matrix_init_kb(void) {
// Keyboard start-up code goes here
// Runs once when the firmware starts up
matrix_init_user();
led_init_ports();
};
void matrix_scan_kb(void) {
// Looping keyboard code goes here
// This runs every cycle (a lot)
matrix_scan_user();
};
void led_init_ports(void) {
/* LEDs on */
}

@ -0,0 +1,21 @@
#ifndef TOKYO60_H
#define TOKYO60_H
#include "quantum.h"
/* tokyo60 Keymap*/
#define TOKYO_KEYMAP( \
K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K1D,\
K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K2D, \
K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K3D, \
K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K4D, \
K42, K43, K46, K4B, K4C \
) { \
{ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \
{ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \
{ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, KC_NO, K2D }, \
{ K30, KC_NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \
{ KC_NO, K42, K43, KC_NO, KC_NO, K46, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, K4B, K4C, K4D } \
}
#endif
Loading…
Cancel
Save