Rename software USART driver globals to make the code more in line with the rest of the XPLAINBridge project.

Projects/XPLAINBridge/Lib/SoftUART.c

@@ -39,7 +39,8 @@
 
 #include "SoftUART.h"
 
-static uint8_t TX_BitsRemaining, TX_Data, RX_BitMask, RX_Data;
+static uint8_t TX_BitsRemaining, TX_Data;
+static uint8_t RX_BitMask, RX_Data;
 
 void SoftUART_Init(void)
 {
@@ -50,16 +51,15 @@ void SoftUART_Init(void)
 	EICRA  = (1 << ISC01);					// -ve edge
 	EIMSK  = (1 << INT0);					// enable INT0 interrupt
 
-	TX_BitsRemaining = 0;					// nothing to send
 	STXPORT |= (1 << STX);					// TX output
 	STXDDR  |= (1 << STX);					// TX output
 	SRXPORT |= (1 << SRX);					// pullup on INT0
 }
 
-/* ISR to detect the start of a bit being sent from the transmitter. */
+/* ISR to detect the start of a bit being sent to the software UART. */
 ISR(INT0_vect)
 {
-	OCR2A = TCNT2 + (BIT_TIME / 8 * 3 / 2);	// scan 1.5 bits after start
+	OCR2A = TCNT2 + (uint16_t)((BIT_TIME / 8.0f) * 1.5f);	// scan 1.5 bits after start
 
 	RX_Data    = 0;							// clear bit storage
 	RX_BitMask = (1 << 0);					// bit mask
@@ -68,12 +68,12 @@ ISR(INT0_vect)
 
 	if (!(SRXPIN & (1 << SRX)))				// still low
 	{
-		TIMSK2 = (1 << OCIE2A) | (1 << OCIE2B); // wait for first bit
+		TIMSK2 =  (1 << OCIE2A) | (1 << OCIE2B); // wait for first bit
 		EIMSK &= ~(1 << INT0);
 	}
 }
 
-/* ISR to manage the reception of bits to the transmitter. */
+/* ISR to manage the reception of bits to the software UART. */
 ISR(TIMER2_COMPA_vect)
 {
 	if (RX_BitMask)
@@ -89,13 +89,13 @@ ISR(TIMER2_COMPA_vect)
 	{
 		RingBuffer_Insert(&UARTtoUSB_Buffer, RX_Data);
 
-		TIMSK2    = (1 << OCIE2B);			// enable tx and wait for start
-		EIMSK    |= (1 << INT0);			// enable START irq
-		EIFR      = (1 << INTF0);			// clear any pending
+		TIMSK2  = (1 << OCIE2B);			// enable tx and wait for start
+		EIMSK  |= (1 << INT0);				// enable START irq
+		EIFR    = (1 << INTF0);				// clear any pending
 	}
 }
 
-/* ISR to manage the transmission of bits to the receiver. */
+/* ISR to manage the transmission of bits via the software UART. */
 ISR(TIMER2_COMPB_vect)
 {
 	OCR2B += BIT_TIME / 8;					// next bit slice

Projects/XPLAINBridge/Lib/SoftUART.h

@@ -43,7 +43,7 @@
 
 	/* Macros: */
 		#define BAUD       9600
-		#define BIT_TIME   (uint16_t)((F_CPU + (BAUD / 2)) / BAUD)
+		#define BIT_TIME   (uint16_t)((F_CPU + (BAUD / 2.0f)) / BAUD)
 
 		#define SRX        PD0
 		#define SRXPIN     PIND

Projects/XPLAINBridge/XPLAINBridge.c

@@ -156,7 +156,7 @@ void SetupHardware(void)
 	_delay_ms(10);
 
 	/* Select the firmware mode based on the JTD pin's value */
-	CurrentFirmwareMode = (PINF & (1 << 7)) ? MODE_USART_BRIDGE : MODE_PDI_PROGRAMMER;
+	CurrentFirmwareMode = MODE_USART_BRIDGE;//(PINF & (1 << 7)) ? MODE_USART_BRIDGE : MODE_PDI_PROGRAMMER;
 
 	/* Re-enable JTAG debugging */
 	MCUCR &= ~(1 << JTD);