Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.
Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.
Altered all low level device and host mode demos to ensure that endpoints and pipes are configured in ascending order properly.
Rewrote all low level host mode demos' configuration descriptor parser code to ensure that pipes are enumerated in ascending order, and to ensure maximum compatibility with devices.
Incremented all device mode demo's device descriptor revision numbers to ensure that any descriptor changes are re-fetched on machines which have enumerated previous versions.
Add new module source variables to the library core makefile, so that module sources can be added to a project's makefile on a per-module rather than per-file basis.
Removed the internal endpoint and pipe memory allocation macros, as this is already performed directly in the code. Simplify the endpoint and pipe reset procedure.
Fixed lack of support for the ATMEGA32U2 in the DFU and CDC class bootloaders
Changed incomplete Webserver project over to using the uIP timer library.
Added brace guards to macros with parameters to prevent unintended changed evaluation of the macro expression.
Minor code cleanups (remove redundant comments, fix spacing, etc.).
Fix up demo documentation device compatibility list to be as general as possible to reduce changes required as Atmel releases more devices within the same USB AVR series.
Added warning to the EVENT_USB_Device_Connect() and EVENT_USB_Device_Disconnect() events that they may be fired multiple times during device enumeration on the series 2 AVRs.
Re-add in flip, flip-ee, dfu and dfu-ee targets to project makefiles (thanks to Opendous Inc.)
Fix allowable F_CPU values comment in project makefiles.
Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.
Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.
Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.
Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.
Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.
Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.
Added new USE_FLASH_DESCRIPTORS compile time option. By default, descriptors can now lie in mixed memory spaces (specified by a new parameter to the CALLBACK_USB_GetDescriptor() function) unless one of the USE_*_DESCRIPTORS compile time option is specified.
Documented FAST_STREAM_TRANSFERS compile time option.
Reduced the TCP window size for the RNDIS demos (Class and LowLevel) to make them compatible with the AT90USB64x.
Seperated out Lib components of the incomplete BluetoothHost demo application out into a seperate Lib subfolder.
Changed F_CLOCK entries in project makefiles to alias to F_CPU by default, as this is the most common case.
Added parameter directions to function parameter documentation.
Added new experimental FAST_STREAM_FUNCTIONS compile time option to speed up stream transfers at the expense of a higher FLASH consumption (needs testing to verify improved throughput).
Remove all Host mode class demos other than the CDCHost class driver demo, so that they can be re-added as they are made once the host mode class framework is designed.
Fixed USB_Host_SendControlRequest() not re-suspending the USB bus when initial device ready-wait fails.
Fixed USB Pad regulator not being disabled on some AVR models when the USB_OPT_REG_DISABLED option is used.
Added new USB_Host_GetDeviceDescriptor() convenience function to retrieve the attached device's Device descriptor.
Make Pipe_ConfigurePipe() mask the given endpoint number against PIPE_EPNUM_MASK to ensure the endpoint IN direction bit is cleared to prevent endpoint type corruption.
Fix documentation mentioning Pipe_GetCurrentToken() function when real name is Pipe_GetPipeToken().
Redocumented all device demos, now that they have changed over to the new USB class drivers.
Added C linkage to class drivers for C++ support.
Added prefixes to most of the class driver constants to prevent name clashes.
Removed scheduler and memory allocation libraries.
Added new EVENT_USB_StartOfFrame event in the library to indicate the start of each USB frame (when generated).
Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt.
Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).
Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.
Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.
Further documentation improvements - removed file view from the main library documentation, replaced file references in the documentation with group references.
The USB_UnhandledControlPacket event has had its parameters removed, in favour of accessing the new USB_ControlRequest structure.
The Endpoint control stream functions now correctly send a ZLP to the host when less data than requested is sent.
Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favour of new Endpoint_ClearIN(), Endpoint_ClearOUT(), Endpoint_ClearControlIN(), Endpoint_ClearControlOUT(), Pipe_ClearIN(), Pipe_ClearOUT(), Pipe_ClearControlIN() and Pipe_ClearControlOUT() macros (done to allow for the detection of packets of zero length).
Renamed *_ReadWriteAllowed() macros to *_IsReadWriteAllowed() to remain consistent with the rest of the LUFA API.
Endpoint_IsSetupReceived() macro has been renamed to Endpoint_IsSETUPReceived(), Endpoint_ClearSetupReceived() macro has been renamed to Endpoint_ClearControlSETUP(), the Pipe_IsSetupSent() macro has been renamed to Pipe_IsSETUPSent() and the Pipe_ClearSetupSent() macro is no longer applicable and should be removed - changes made to compliment the new endpoint and pipe bank management API.
Updated all demos, bootloaders and projects to use the new endpoint and pipe management APIs (thanks to Roman Thiel).
Updated library doxygen documentation, added groups, changed documentation macro functions to real functions for clarity.
Removed old endpoint and pipe aliased read/write/discard routines which did not have an explicit endian specifier for clarity.
Removed the ButtLoadTag.h header file, as no one used for its intended purpose anyway.
Dean Camera