ec537fd84d
Re-add in old Endpoint/Pipe workaround for unordered pipes - add new ORDERED_EP_CONFIG compile time option to override the workaround and use the previous behaviour that imposes correct Endpoint/Pipe ordering but produces smaller compiled code.
14 years ago
0595ac27d5
Commit for 101122 release.
14 years ago
fb76acb084
Renamed the EVENT_USB_Device_UnhandledControlRequest() event to EVENT_USB_Device_ControlRequest() as it is now fired before the library request handlers, not afterwards.
14 years ago
b37d77eab3
All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included.
...
All LowLevel demos changed to use the constants and types defined in the USB class drivers.
14 years ago
9464fa168e
Renamed ENDPOINT_DOUBLEBANK_SUPPORTED() to ENDPOINT_BANKS_SUPPORTED() and changed it to return the maximum number of supported banks for the given endpoint.
14 years ago
5a4def7478
Clean up excessive whitespace at the end of each line using the wspurify tool made by Laszlo Monda
14 years ago
7aaced1e8b
Remove USB_MODE_* macros, replace with a semantically linked USB_Modes_t enum.
...
Moved the USB device selection logic for ENDPOINT_TOTAL_ENDPOINTS further up in Endpoint.h to where the endpoint bank capabilities are determined, to reduce the total number of device-specific logic.
Change USB_Host_WaitMS() to test and disable the HSOFI interrupt before resuming the bus, so that it does not fire before the delay loop has run.
Add missing const qualifier to the parameter of USB_Host_ClearPipeStall().
14 years ago
a1e453e900
Make Host mode Class drivers only set the class driver instance's state values once a compatible interface has been found within the device.
14 years ago
158afe9109
Reverted Endpoint/Pipe non-sequential configuration hack, placed restriction on the configuration order instead to ensure maximum reliability.
...
Altered all low level device and host mode demos to ensure that endpoints and pipes are configured in ascending order properly.
Rewrote all low level host mode demos' configuration descriptor parser code to ensure that pipes are enumerated in ascending order, and to ensure maximum compatibility with devices.
Incremented all device mode demo's device descriptor revision numbers to ensure that any descriptor changes are re-fetched on machines which have enumerated previous versions.
14 years ago
713670043a
Move out many of the common class driver constants into grouped enums, to make them more managable.
...
Add new CDC descriptor structs to the CDC class driver, so that the CDC demos can use human readable field names.
Rename prefix for Still Image Host class driver functions from "SImage_" to "SI_" to remain consistent with the rest of the driver.
14 years ago
cce8760b91
Removed the EVENT_USB_InitFailure() event, as not specifying a USB mode to USB_Init() now defaults the controller into UID selection mode.
14 years ago
a0f9192568
Minor documentation corrections.
14 years ago
c166dfc64e
Added class specific descriptor type defines with standard USB-IF element naming.
14 years ago
7aaf9b2036
Added new PRNT_Host_BytesReceived() and PRNT_Host_ReceiveByte() functions to the Print Host Class driver.
14 years ago
092f82e06f
Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove the need for extra casting inside the callback (thanks to Jonathan Kollasch).
14 years ago
e72f424f64
Split out endpoint and pipe stream functions into new EndpointStream.c/.h and PipeStream.c/.h files.
14 years ago
be520aed52
Add notification endpoint to the incomplete TMC demo.
14 years ago
9274610a48
Commit for the 100807 release.
14 years ago
612df774d9
Oops - fix mixed "initialize" and "initialise" - opt for American spelling due to its wide use in technical standards.
14 years ago
0f45b9c8e0
More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.
14 years ago
24e621a8d8
Altered the CDC Deivice and Host Class drivers' receive byte routines, so that no data is indicated by a negative return value.
...
Added auto flushing of OUT data to the CDC Host Class driver's USBTask function to automatically flush the send pipe buffer.
14 years ago
3a79548dc2
Add TMC device capabilities to the incomplete TMC demo.
15 years ago
9b0e4b8356
Convert over internal pseudo-function macros to true inline functions for added type-safety and compile-checking.
15 years ago
99d8a39363
Move and rename DevChaper9.c/.h and HostChapter9.c/.h to the HighLevel directory, new named DeviceStandardReq.c/.h and HostStandardReq.c/.h.
...
Rename LowLevel.c/.h to USBController.c/.h.
Remove dependancies on the complete <avr/io.h> header in the HighLevel USB driver directory, to ensure less work is required in later (possible) ports.
15 years ago
6b5e684c77
Update makefiles to use the latest WinAVR/Atmel toolchain makefile template.
...
Add new module source variables to the library core makefile, so that module sources can be added to a project's makefile on a per-module rather than per-file basis.
15 years ago
8b053d6ba5
Added new Drivers/USB/LowLevel/Device.c file to house Device mode specific functions that are more complicated than simple macros. Moved USB_Device_SendRemoteWakeup() to the new Device.c source file and corrected it to unfreeze and restart the USB controller clock before issuing a Remote Wakeup request.
...
Removed the USB_Device_IsRemoteWakeupSent() and USB_Device_IsUSBSuspended() macros, as they are now obsolete.
15 years ago
711542ee89
Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.
15 years ago
ff61dfa505
Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).
15 years ago
80d85090ba
Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.
15 years ago
6b7770ef2b
Commit for 100513 re-release due to critical device mode bug.
15 years ago
3080988b35
Commit for the 100512 release.
15 years ago
05ac59d0ee
Add new ReportType parameter to the HID class driver device callback and host report sending routines.
...
Renamed internal Host mode Class driver descriptor comparator callback routines so that they all start with a uniform DCOMP_{Class Abbreviation}_ prefix.
15 years ago
071e02c6b6
Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.
15 years ago
e977774d4e
Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.
15 years ago
59c4871f80
USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.
15 years ago
c0c982df7a
Added a timeout value to the TWI_StartTransmission() function, within which the addressed device must respond.
...
Fixed TWI_StartTransmission() corrupting the contents of the GPIOR0 register.
15 years ago
071fd8ce53
Revert changes made for the partial port to the AVR32 architecture.
15 years ago
e11fddfe66
Update Temperature board driver to be AVR32 compatible when the ADC peripheral driver is eventually ported. Make architecture includes explicit for both the AVR32 and the AVR8, to make way for future architecture ports.
...
Add SPI driver aliases for the old function names in the AVR8 driver, so that existing code will still compile against the new version.
15 years ago
ce8d0424b1
AVRISP programmer project now has a more robust timeout system, allowing for a doubling of the software USART speed for PDI and TPI programming.
15 years ago
04d40897cf
Commit for the 100219 release.
15 years ago
b6a4584a19
Fixed Pipe_IsEndpointBound() function not taking the endpoint's direction into account.
...
Re-added Pipe_IsEndpointBound() calls to the CDC and RNDIS host class drivers, not that the function has the correct behaviour for devices with bidirectional endpoints.
15 years ago
fa3135d485
Add MIME type handling to the Webserver project, so that files of different types (e.g. images) can be served out to HTTP clients.
15 years ago
b68f7f1649
Added explicit ADC channel masks for the standard set of ADC channels, as the single-ended channel MUX masks are not equal to the channel number on some AVR models. Changed demos to use the new channel masks when using the ADC driver.
15 years ago
d97db1120b
Added support to the MIDI Class drivers for packed data, where multiple MIDI events are packed into a single USB packet. Added new MIDI Class driver flush routines to override packing behaviour.
15 years ago
cda88cf97c
Start of implementation of the low level TPI programming protocol in the AVRISP project.
15 years ago
2919aeeaab
Fixed HID Parser not distributing the Usage Min and Usage Max values across an array of report items.
...
Added new HID_ALIGN_DATA() macro to return the pre-retrieved value of a HID report item, left-aligned to a given datatype.
Added new PreviousValue to the HID Report Parser report item structure, for easy monitoring of previous report item values.
15 years ago
5aa2b26261
Added new RNDIS Host class driver and the beginnings of a RNDISEthernetHost Class Driver demo.
...
Fixed all Class drivers to ensure they have appropriate guards on each function to ensure the device is enumerated before running, fixed error codes on all guards to return "DeviceDisconnected" where possble.
Renamed HOST_SENDCONTROL_DeviceDisconnect enum value to HOST_SENDCONTROL_DeviceDisconnected to be in line with the rest of the library enum error codes.
15 years ago
702bec892d
Fixed misnamed SI_Host_USBTask() and SI_Host_ConfigurePipes() functions.
15 years ago
8b009bc113
Added new ReportType parameter to the HID Device Class driver CALLBACK_HID_Device_CreateHIDReport() callback to indicate the report type to generate.
15 years ago
86db035b1e
Add activity LED updates to the AVRISP project.
15 years ago
Dean Camera