* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
* Add iPhone/iPad LED support to Helix default keymap
* renumber _ADJUST for shrink program size
* Fix Helix i2c wrong bit rate
* add helix serial debug code
* serial debug macro move from config.h to serial.h
* helix serial.c debugging...
* refine debug macros
* add some comments
* add SELECT_SERIAL_SPEED
* add comments
* debugging sync_send/sync_recv
* add very high speed
* fix sync_send/sync_recv
* fix com. start and switch send/recv
* debug mode off
* remove debug codes
* temporary change, compiling C, C++ and ASM without -g
* helix config.h refine
* Revert "temporary change, compiling C, C++ and ASM without -g"
This reverts commit e9730cbbfd.
* add change_reciver2sender()/change_sender2reciver()
This is a change to improve readability.
* txled, rxled off in matrix_init()
* add serial_send_packet() / serial_recive_packet()
This is a change to reduce object size.
* add serial_low() at ISR() top
* add __attribute__((always_inline)) to some functions
* modify serial_send_packet()/serial_recive_packet()
A little, object size reduction.
A little, speedup.
* add debug code to helix/serial.c
* Adjust sampling timing of serial signal being received
* add split_scomm.c/split_scomm.h and change serial.c/serial.h
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
* add split_scomm.c/split_scomm.h into helix/rev1
* reduce object size helix/rev2/matrix.c
* remove checksum check, add parity check
* force occur parity error for test
* parity test ok. remove test code
* change some comment & add skip code when buffer_size == 0
* serial.c: multiple types of transaction support
Add 4 bits transaction-type field at packet top.
Select Transaction Descriptor Table entry by transaction-type.
* helix serial master-slave transaction optimize
Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized.
* add debug code for retry
* add comment into each config.h
* fix ISR status drop
* add a debug macro 'debug_retry_chg()'
* reduce led_test size
* remove debug code from helix/serial.c and etc.
* helix:five_rows change TAPPING_TERM value 140
* Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement.
- The difference with the original let's split's serial.c
- It's high-speed about 4 times.
- Stable bi-directional data transfer. (Helix need master to slave transfer)
- serial.h was divided 2 files, serial_config.h and sereial.h
- With multiple types of transaction support, communication contents can be optimized. (NEW flexible API)
- USE OLD Simple APIs (compatible with let's split serial.c)
- files :
- serial_config.h -- hardware configuration (need include by config.h)
- serial.c/serial.h -- serial communication
- USE NEW flexible APIs. (Support multi-type transaction function.)
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
- files
- split_scomm.c -- communication buffer is defined in here. call by matrix.c.
- split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c
- serial_config.h -- hardware configuration (need include by config.h)
To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION
- serial.c/serial.h -- serial communication lower layer
- NEW APIs for serial.c / serial.h (The lower layer)
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table);
int soft_serial_transaction(int sstd_index);
int soft_serial_get_and_clean_target_status(int sstd_index);
- NEW APIs for split_scomm.c / split_scomm.h (The upper layer)
move from old serial.c the following buffer and functions
serial_slave_buffer[]
serial_master_buffer[]
void serial_master_init(void)
void serial_slave_init(void)
int serial_update_buffers(void)
define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
* fix comment typo
* Fix the value of helix:five_rows variable HELIX_ROWS to 5.
* led_test rules.mk some change
* Separate common parts of helix/rev2/keymaps/*/rules.mk into helix/rev2/keymaps_common.mk
* helix/rev2/keymaps/edvorakjp/rules.mk use helix/rev2/keymaps_common.mk
* Separate common parts of helix/pico/keymaps/*/rules.mk into helix/pico/keymaps_common.mk
* Helix each keymap's using rgblight mode symbol instead magic number
No change in build result.
* Helix pico keymaps: make rgblight modes selectable.
No change in build result.
* Helix rev2 keymaps: make rgblight modes selectable.
No change in build result.
* fixed Helix froggy/keymap.c: invalid rgblight mode value 0 to 1 (=RGBLIGHT_MODE_STATIC_LIGHT)
* Deselect RGB_TEST and ALTERNATING in Helix rev2,pico keymaps config.h.
* Merge branch 'master' of https://github.com/qmk/qmk_firmware
* revert 955dcbc
* delete keymaps_common.mk
* add LAYOUT_kc() to keyboards/helix/pico/pico.h
* add initial support for hadron ver3
* add initial support for hadron ver3
* pull qwiic support for micro_led to be modified for use in hadron's 64x24 ssd1306 oled display
* initial work on OLED using qwiic driver
* early work to get 128x32 oled working by redefining qwiic micro oled parameters. Currently working, but would affect qwiic's micro oled functionality
* moved oled defines to config.h and added ifndef to micro_oled driver
* WORKING :D - note, still work in progress to get the start location correct on the 128x32 display.
* added equation to automatically calculate display offset based on screen width
* adding time-out timer to oled display
* changed read lock staus via read_led_state
* lock indications fixes
* Added scroll lock indication to oled
* add support for DRV2605 haptic driver
* Improve readabiity of DRV2605 driver.
-added typedef for waveform library
-added unions for registers
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Fixes for PR
* PR fixes
* fix old persistent layer function to use new set_single_persistent_default_layer
* fix issues with changing makefile defines that broken per-key haptic pulse
* Comment fixes
* Add definable parameter and auto-calibration based on motor choice
* Fix up screen off timer of helix
* Fix Up ScreenOffInterval exceeded uint16_t
* Fix Up never waking up once screen off if in case of matrix are not dirty
* Changing referenIng incorrect constant name
* OLED_ENABLED => SSD1306OLED
* Improve internal processing of process_record_kb()
* Use the return value of process_record_gfx()
* Move a include statement into #ifdef block
Move #include "ssd1306.h` statement into #ifdef block
* Move process_record_kbI()
Move process_record_kb() from helix.c to rev1.c/rev2.c/pico.c
* Move process_record_kb()
The new simple API can be selected.
Previous version, can select two way.
* use old API (compatible with let's split serial.c)
* use new API (multi-type transaction)
This version, can select three way.
* use old API (compatible with let's split serial.c)
* use new API (single-type transaction)
* use new API (multi-type transaction)
There is no change in the code generated by this change.
* helix/serial.c add support PD1,PD3,PE6 and configuration simplify
* Add comment about ATmega32U4 I2C
* Add compile time check for ATmega32U4 I2C
* change TAB code to 8 SPACE code
* Helix serial.c PORTD,PD0 test. OK
OK PD0
- PD1
OK PD2
- PD3
- PE6
* Helix serial.c PORTD,PD1 test. OK
OK PD0
OK PD1
OK PD2
- PD3
- PE6
* Helix serial.c PORTD,PD3 test. OK
OK PD0
OK PD1
OK PD2
OK PD3
- PE6
* Helix serial.c PORTE,PD6 test. OK
OK PD0
OK PD1
OK PD2
OK PD3
OK PE6
* Helix serial.c: PD0,PD1,PD3,PE6 all test end
* Helix serial.c: rename SOFT_SERIAL_PORT to SOFT_SERIAL_PIN
* Helix serial.c add debug code
* Helix serial.c: add transaction ID range check
* Helix serial.c debug code update
* Helix serial.c debug code update
* Helix serial.c: Strict checking of the value of tid.
* adjust the delay of serial.c
* Helix serial.c: remove debug code
* remove EXTRAFLAGS += -DCONSOLE_ENABLE from five_rows/rules.mk
tmk_core/common.mk has
>ifeq ($(strip $(CONSOLE_ENABLE)), yes)
> TMK_COMMON_DEFS += -DCONSOLE_ENABLE
* Fix error handling in split_scomm.c
* add some comment to serial.c
* add some comment about SELECT_SOFT_SERIAL_SPEED
* Helix each keymap's using rgblight mode symbol instead magic number
No change in build result.
* Helix pico keymaps: make rgblight modes selectable.
No change in build result.
* Helix rev2 keymaps: make rgblight modes selectable.
No change in build result.
* fixed Helix froggy/keymap.c: invalid rgblight mode value 0 to 1 (=RGBLIGHT_MODE_STATIC_LIGHT)
* Deselect RGB_TEST and ALTERNATING in Helix rev2,pico keymaps config.h.
* Helix: make rgblight modes selectable.
No change in build result.
* edit the comment of helix/rev2/keymaps/default/keymap.c
* Helix led_test keymap: reduced the size.
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* add change_reciver2sender()/change_sender2reciver()
This is a change to improve readability.
* txled, rxled off in matrix_init()
* add serial_send_packet() / serial_recive_packet()
This is a change to reduce object size.
* add serial_low() at ISR() top
* add __attribute__((always_inline)) to some functions
* modify serial_send_packet()/serial_recive_packet()
A little, object size reduction.
A little, speedup.
* add debug code to helix/serial.c
* Adjust sampling timing of serial signal being received
* add split_scomm.c/split_scomm.h and change serial.c/serial.h
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
* add split_scomm.c/split_scomm.h into helix/rev1
* reduce object size helix/rev2/matrix.c
* remove checksum check, add parity check
* force occur parity error for test
* parity test ok. remove test code
* change some comment & add skip code when buffer_size == 0
* serial.c: multiple types of transaction support
Add 4 bits transaction-type field at packet top.
Select Transaction Descriptor Table entry by transaction-type.
* helix serial master-slave transaction optimize
Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized.
* add debug code for retry
* add comment into each config.h
* fix ISR status drop
* add a debug macro 'debug_retry_chg()'
* reduce led_test size
* remove debug code from helix/serial.c and etc.
* helix:five_rows change TAPPING_TERM value 140
* Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement.
- The difference with the original let's split's serial.c
- It's high-speed about 4 times.
- Stable bi-directional data transfer. (Helix need master to slave transfer)
- serial.h was divided 2 files, serial_config.h and sereial.h
- With multiple types of transaction support, communication contents can be optimized. (NEW flexible API)
- USE OLD Simple APIs (compatible with let's split serial.c)
- files :
- serial_config.h -- hardware configuration (need include by config.h)
- serial.c/serial.h -- serial communication
- USE NEW flexible APIs. (Support multi-type transaction function.)
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
- files
- split_scomm.c -- communication buffer is defined in here. call by matrix.c.
- split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c
- serial_config.h -- hardware configuration (need include by config.h)
To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION
- serial.c/serial.h -- serial communication lower layer
- NEW APIs for serial.c / serial.h (The lower layer)
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table);
int soft_serial_transaction(int sstd_index);
int soft_serial_get_and_clean_target_status(int sstd_index);
- NEW APIs for split_scomm.c / split_scomm.h (The upper layer)
move from old serial.c the following buffer and functions
serial_slave_buffer[]
serial_master_buffer[]
void serial_master_init(void)
void serial_slave_init(void)
int serial_update_buffers(void)
define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
* now helix led_test local rgblight.[ch] not use. remove.
* greatly simplify keyboards/helix/rev2/keymaps/led_test/keymap.c
Helix keymap 'led_test' use modified default/keymap.c
* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
* Add iPhone/iPad LED support to Helix default keymap
* add Freggy keymap
* adjust the delay of serial.c
* change readme
* renumber _ADJUST for shrink program size
* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
Takeshi ISHII