Compare commits

...

2 Commits

@ -0,0 +1,9 @@
/* Address for jumping to bootloader on STM32 chips. */
/* It is chip dependent, the correct number can be looked up here (page 175):
* http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
* This also requires a patch to chibios:
* <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
*/
// STM32L476 Bootloader address
#define STM32_BOOTLOADER_ADDRESS 0x1FFF0000

@ -0,0 +1,520 @@
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file templates/chconf.h
* @brief Configuration file template.
* @details A copy of this file must be placed in each project directory, it
* contains the application specific kernel settings.
*
* @addtogroup config
* @details Kernel related settings and hooks.
* @{
*/
#ifndef CHCONF_H
#define CHCONF_H
#define _CHIBIOS_RT_CONF_
/*===========================================================================*/
/**
* @name System timers settings
* @{
*/
/*===========================================================================*/
/**
* @brief System time counter resolution.
* @note Allowed values are 16 or 32 bits.
*/
#define CH_CFG_ST_RESOLUTION 32
/**
* @brief System tick frequency.
* @details Frequency of the system timer that drives the system ticks. This
* setting also defines the system tick time unit.
*/
#define CH_CFG_ST_FREQUENCY 10000
/**
* @brief Time delta constant for the tick-less mode.
* @note If this value is zero then the system uses the classic
* periodic tick. This value represents the minimum number
* of ticks that is safe to specify in a timeout directive.
* The value one is not valid, timeouts are rounded up to
* this value.
*/
#define CH_CFG_ST_TIMEDELTA 2
/** @} */
/*===========================================================================*/
/**
* @name Kernel parameters and options
* @{
*/
/*===========================================================================*/
/**
* @brief Round robin interval.
* @details This constant is the number of system ticks allowed for the
* threads before preemption occurs. Setting this value to zero
* disables the preemption for threads with equal priority and the
* round robin becomes cooperative. Note that higher priority
* threads can still preempt, the kernel is always preemptive.
* @note Disabling the round robin preemption makes the kernel more compact
* and generally faster.
* @note The round robin preemption is not supported in tickless mode and
* must be set to zero in that case.
*/
#define CH_CFG_TIME_QUANTUM 0
/**
* @brief Managed RAM size.
* @details Size of the RAM area to be managed by the OS. If set to zero
* then the whole available RAM is used. The core memory is made
* available to the heap allocator and/or can be used directly through
* the simplified core memory allocator.
*
* @note In order to let the OS manage the whole RAM the linker script must
* provide the @p __heap_base__ and @p __heap_end__ symbols.
* @note Requires @p CH_CFG_USE_MEMCORE.
*/
#define CH_CFG_MEMCORE_SIZE 0
/**
* @brief Idle thread automatic spawn suppression.
* @details When this option is activated the function @p chSysInit()
* does not spawn the idle thread. The application @p main()
* function becomes the idle thread and must implement an
* infinite loop.
*/
#define CH_CFG_NO_IDLE_THREAD FALSE
/** @} */
/*===========================================================================*/
/**
* @name Performance options
* @{
*/
/*===========================================================================*/
/**
* @brief OS optimization.
* @details If enabled then time efficient rather than space efficient code
* is used when two possible implementations exist.
*
* @note This is not related to the compiler optimization options.
* @note The default is @p TRUE.
*/
#define CH_CFG_OPTIMIZE_SPEED TRUE
/** @} */
/*===========================================================================*/
/**
* @name Subsystem options
* @{
*/
/*===========================================================================*/
/**
* @brief Time Measurement APIs.
* @details If enabled then the time measurement APIs are included in
* the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_TM TRUE
/**
* @brief Threads registry APIs.
* @details If enabled then the registry APIs are included in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_REGISTRY TRUE
/**
* @brief Threads synchronization APIs.
* @details If enabled then the @p chThdWait() function is included in
* the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_WAITEXIT TRUE
/**
* @brief Semaphores APIs.
* @details If enabled then the Semaphores APIs are included in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_SEMAPHORES TRUE
/**
* @brief Semaphores queuing mode.
* @details If enabled then the threads are enqueued on semaphores by
* priority rather than in FIFO order.
*
* @note The default is @p FALSE. Enable this if you have special
* requirements.
* @note Requires @p CH_CFG_USE_SEMAPHORES.
*/
#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE
/**
* @brief Mutexes APIs.
* @details If enabled then the mutexes APIs are included in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_MUTEXES TRUE
/**
* @brief Enables recursive behavior on mutexes.
* @note Recursive mutexes are heavier and have an increased
* memory footprint.
*
* @note The default is @p FALSE.
* @note Requires @p CH_CFG_USE_MUTEXES.
*/
#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE
/**
* @brief Conditional Variables APIs.
* @details If enabled then the conditional variables APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_MUTEXES.
*/
#define CH_CFG_USE_CONDVARS TRUE
/**
* @brief Conditional Variables APIs with timeout.
* @details If enabled then the conditional variables APIs with timeout
* specification are included in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_CONDVARS.
*/
#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE
/**
* @brief Events Flags APIs.
* @details If enabled then the event flags APIs are included in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_EVENTS TRUE
/**
* @brief Events Flags APIs with timeout.
* @details If enabled then the events APIs with timeout specification
* are included in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_EVENTS.
*/
#define CH_CFG_USE_EVENTS_TIMEOUT TRUE
/**
* @brief Synchronous Messages APIs.
* @details If enabled then the synchronous messages APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_MESSAGES TRUE
/**
* @brief Synchronous Messages queuing mode.
* @details If enabled then messages are served by priority rather than in
* FIFO order.
*
* @note The default is @p FALSE. Enable this if you have special
* requirements.
* @note Requires @p CH_CFG_USE_MESSAGES.
*/
#define CH_CFG_USE_MESSAGES_PRIORITY FALSE
/**
* @brief Mailboxes APIs.
* @details If enabled then the asynchronous messages (mailboxes) APIs are
* included in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_SEMAPHORES.
*/
#define CH_CFG_USE_MAILBOXES TRUE
/**
* @brief Core Memory Manager APIs.
* @details If enabled then the core memory manager APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_MEMCORE TRUE
/**
* @brief Heap Allocator APIs.
* @details If enabled then the memory heap allocator APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
* @p CH_CFG_USE_SEMAPHORES.
* @note Mutexes are recommended.
*/
#define CH_CFG_USE_HEAP TRUE
/**
* @brief Memory Pools Allocator APIs.
* @details If enabled then the memory pools allocator APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
*/
#define CH_CFG_USE_MEMPOOLS TRUE
/**
* @brief Dynamic Threads APIs.
* @details If enabled then the dynamic threads creation APIs are included
* in the kernel.
*
* @note The default is @p TRUE.
* @note Requires @p CH_CFG_USE_WAITEXIT.
* @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
*/
#define CH_CFG_USE_DYNAMIC TRUE
/** @} */
/*===========================================================================*/
/**
* @name Debug options
* @{
*/
/*===========================================================================*/
/**
* @brief Debug option, kernel statistics.
*
* @note The default is @p FALSE.
*/
#define CH_DBG_STATISTICS FALSE
/**
* @brief Debug option, system state check.
* @details If enabled the correct call protocol for system APIs is checked
* at runtime.
*
* @note The default is @p FALSE.
*/
#define CH_DBG_SYSTEM_STATE_CHECK FALSE
/**
* @brief Debug option, parameters checks.
* @details If enabled then the checks on the API functions input
* parameters are activated.
*
* @note The default is @p FALSE.
*/
#define CH_DBG_ENABLE_CHECKS FALSE
/**
* @brief Debug option, consistency checks.
* @details If enabled then all the assertions in the kernel code are
* activated. This includes consistency checks inside the kernel,
* runtime anomalies and port-defined checks.
*
* @note The default is @p FALSE.
*/
#define CH_DBG_ENABLE_ASSERTS FALSE
/**
* @brief Debug option, trace buffer.
* @details If enabled then the trace buffer is activated.
*
* @note The default is @p CH_DBG_TRACE_MASK_DISABLED.
*/
#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED
/**
* @brief Trace buffer entries.
* @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
* different from @p CH_DBG_TRACE_MASK_DISABLED.
*/
#define CH_DBG_TRACE_BUFFER_SIZE 128
/**
* @brief Debug option, stack checks.
* @details If enabled then a runtime stack check is performed.
*
* @note The default is @p FALSE.
* @note The stack check is performed in a architecture/port dependent way.
* It may not be implemented or some ports.
* @note The default failure mode is to halt the system with the global
* @p panic_msg variable set to @p NULL.
*/
#define CH_DBG_ENABLE_STACK_CHECK FALSE
/**
* @brief Debug option, stacks initialization.
* @details If enabled then the threads working area is filled with a byte
* value when a thread is created. This can be useful for the
* runtime measurement of the used stack.
*
* @note The default is @p FALSE.
*/
#define CH_DBG_FILL_THREADS FALSE
/**
* @brief Debug option, threads profiling.
* @details If enabled then a field is added to the @p thread_t structure that
* counts the system ticks occurred while executing the thread.
*
* @note The default is @p FALSE.
* @note This debug option is not currently compatible with the
* tickless mode.
*/
#define CH_DBG_THREADS_PROFILING FALSE
/** @} */
/*===========================================================================*/
/**
* @name Kernel hooks
* @{
*/
/*===========================================================================*/
/**
* @brief Threads descriptor structure extension.
* @details User fields added to the end of the @p thread_t structure.
*/
#define CH_CFG_THREAD_EXTRA_FIELDS \
/* Add threads custom fields here.*/
/**
* @brief Threads initialization hook.
* @details User initialization code added to the @p chThdInit() API.
*
* @note It is invoked from within @p chThdInit() and implicitly from all
* the threads creation APIs.
*/
#define CH_CFG_THREAD_INIT_HOOK(tp) { \
/* Add threads initialization code here.*/ \
}
/**
* @brief Threads finalization hook.
* @details User finalization code added to the @p chThdExit() API.
*/
#define CH_CFG_THREAD_EXIT_HOOK(tp) { \
/* Add threads finalization code here.*/ \
}
/**
* @brief Context switch hook.
* @details This hook is invoked just before switching between threads.
*/
#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \
/* Context switch code here.*/ \
}
/**
* @brief ISR enter hook.
*/
#define CH_CFG_IRQ_PROLOGUE_HOOK() { \
/* IRQ prologue code here.*/ \
}
/**
* @brief ISR exit hook.
*/
#define CH_CFG_IRQ_EPILOGUE_HOOK() { \
/* IRQ epilogue code here.*/ \
}
/**
* @brief Idle thread enter hook.
* @note This hook is invoked within a critical zone, no OS functions
* should be invoked from here.
* @note This macro can be used to activate a power saving mode.
*/
#define CH_CFG_IDLE_ENTER_HOOK() { \
/* Idle-enter code here.*/ \
}
/**
* @brief Idle thread leave hook.
* @note This hook is invoked within a critical zone, no OS functions
* should be invoked from here.
* @note This macro can be used to deactivate a power saving mode.
*/
#define CH_CFG_IDLE_LEAVE_HOOK() { \
/* Idle-leave code here.*/ \
}
/**
* @brief Idle Loop hook.
* @details This hook is continuously invoked by the idle thread loop.
*/
#define CH_CFG_IDLE_LOOP_HOOK() { \
/* Idle loop code here.*/ \
}
/**
* @brief System tick event hook.
* @details This hook is invoked in the system tick handler immediately
* after processing the virtual timers queue.
*/
#define CH_CFG_SYSTEM_TICK_HOOK() { \
/* System tick event code here.*/ \
}
/**
* @brief System halt hook.
* @details This hook is invoked in case to a system halting error before
* the system is halted.
*/
#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \
/* System halt code here.*/ \
}
/**
* @brief Trace hook.
* @details This hook is invoked each time a new record is written in the
* trace buffer.
*/
#define CH_CFG_TRACE_HOOK(tep) { \
/* Trace code here.*/ \
}
/** @} */
/*===========================================================================*/
/* Port-specific settings (override port settings defaulted in chcore.h). */
/*===========================================================================*/
#endif /* CHCONF_H */
/** @} */

@ -0,0 +1,7 @@
#ifndef KEYBOARDS_CHIBIOS_TEST_STM32_L476_ONEKEY_CONFIG_H_
#define KEYBOARDS_CHIBIOS_TEST_STM32_L476_ONEKEY_CONFIG_H_
#include "../config.h"
#undef NKRO_ENABLE
#endif /* KEYBOARDS_CHIBIOS_TEST_STM32_L476_ONEKEY_CONFIG_H_ */

@ -0,0 +1,2 @@
#!/bin/bash
Arduino_STM32_usb_hid/tools/linux/maple_upload ttyACM0 2 1EAF:0003 build/ch.bin

@ -0,0 +1,388 @@
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file templates/halconf.h
* @brief HAL configuration header.
* @details HAL configuration file, this file allows to enable or disable the
* various device drivers from your application. You may also use
* this file in order to override the device drivers default settings.
*
* @addtogroup HAL_CONF
* @{
*/
#ifndef HALCONF_H
#define HALCONF_H
#include "mcuconf.h"
/**
* @brief Enables the PAL subsystem.
*/
#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
#define HAL_USE_PAL TRUE
#endif
/**
* @brief Enables the ADC subsystem.
*/
#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
#define HAL_USE_ADC FALSE
#endif
/**
* @brief Enables the CAN subsystem.
*/
#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
#define HAL_USE_CAN FALSE
#endif
/**
* @brief Enables the DAC subsystem.
*/
#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
#define HAL_USE_DAC FALSE
#endif
/**
* @brief Enables the EXT subsystem.
*/
#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
#define HAL_USE_EXT FALSE
#endif
/**
* @brief Enables the GPT subsystem.
*/
#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
#define HAL_USE_GPT FALSE
#endif
/**
* @brief Enables the I2C subsystem.
*/
#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
#define HAL_USE_I2C FALSE
#endif
/**
* @brief Enables the I2S subsystem.
*/
#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
#define HAL_USE_I2S FALSE
#endif
/**
* @brief Enables the ICU subsystem.
*/
#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
#define HAL_USE_ICU FALSE
#endif
/**
* @brief Enables the MAC subsystem.
*/
#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
#define HAL_USE_MAC FALSE
#endif
/**
* @brief Enables the MMC_SPI subsystem.
*/
#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
#define HAL_USE_MMC_SPI FALSE
#endif
/**
* @brief Enables the PWM subsystem.
*/
#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
#define HAL_USE_PWM FALSE
#endif
/**
* @brief Enables the QSPI subsystem.
*/
#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
#define HAL_USE_QSPI FALSE
#endif
/**
* @brief Enables the RTC subsystem.
*/
#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
#define HAL_USE_RTC FALSE
#endif
/**
* @brief Enables the SDC subsystem.
*/
#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
#define HAL_USE_SDC FALSE
#endif
/**
* @brief Enables the SERIAL subsystem.
*/
#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
#define HAL_USE_SERIAL FALSE
#endif
/**
* @brief Enables the SERIAL over USB subsystem.
*/
#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
#define HAL_USE_SERIAL_USB FALSE
#endif
/**
* @brief Enables the SPI subsystem.
*/
#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
#define HAL_USE_SPI FALSE
#endif
/**
* @brief Enables the UART subsystem.
*/
#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
#define HAL_USE_UART FALSE
#endif
/**
* @brief Enables the USB subsystem.
*/
#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
#define HAL_USE_USB TRUE
#endif
/**
* @brief Enables the WDG subsystem.
*/
#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
#define HAL_USE_WDG FALSE
#endif
/*===========================================================================*/
/* ADC driver related settings. */
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
#define ADC_USE_WAIT TRUE
#endif
/**
* @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define ADC_USE_MUTUAL_EXCLUSION TRUE
#endif
/*===========================================================================*/
/* CAN driver related settings. */
/*===========================================================================*/
/**
* @brief Sleep mode related APIs inclusion switch.
*/
#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
#define CAN_USE_SLEEP_MODE TRUE
#endif
/*===========================================================================*/
/* I2C driver related settings. */
/*===========================================================================*/
/**
* @brief Enables the mutual exclusion APIs on the I2C bus.
*/
#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define I2C_USE_MUTUAL_EXCLUSION TRUE
#endif
/*===========================================================================*/
/* MAC driver related settings. */
/*===========================================================================*/
/**
* @brief Enables an event sources for incoming packets.
*/
#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
#define MAC_USE_ZERO_COPY FALSE
#endif
/**
* @brief Enables an event sources for incoming packets.
*/
#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
#define MAC_USE_EVENTS TRUE
#endif
/*===========================================================================*/
/* MMC_SPI driver related settings. */
/*===========================================================================*/
/**
* @brief Delays insertions.
* @details If enabled this options inserts delays into the MMC waiting
* routines releasing some extra CPU time for the threads with
* lower priority, this may slow down the driver a bit however.
* This option is recommended also if the SPI driver does not
* use a DMA channel and heavily loads the CPU.
*/
#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
#define MMC_NICE_WAITING TRUE
#endif
/*===========================================================================*/
/* SDC driver related settings. */
/*===========================================================================*/
/**
* @brief Number of initialization attempts before rejecting the card.
* @note Attempts are performed at 10mS intervals.
*/
#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
#define SDC_INIT_RETRY 100
#endif
/**
* @brief Include support for MMC cards.
* @note MMC support is not yet implemented so this option must be kept
* at @p FALSE.
*/
#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
#define SDC_MMC_SUPPORT FALSE
#endif
/**
* @brief Delays insertions.
* @details If enabled this options inserts delays into the MMC waiting
* routines releasing some extra CPU time for the threads with
* lower priority, this may slow down the driver a bit however.
*/
#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
#define SDC_NICE_WAITING TRUE
#endif
/*===========================================================================*/
/* SERIAL driver related settings. */
/*===========================================================================*/
/**
* @brief Default bit rate.
* @details Configuration parameter, this is the baud rate selected for the
* default configuration.
*/
#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
#define SERIAL_DEFAULT_BITRATE 38400
#endif
/**
* @brief Serial buffers size.
* @details Configuration parameter, you can change the depth of the queue
* buffers depending on the requirements of your application.
* @note The default is 16 bytes for both the transmission and receive
* buffers.
*/
#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
#define SERIAL_BUFFERS_SIZE 16
#endif
/*===========================================================================*/
/* SERIAL_USB driver related setting. */
/*===========================================================================*/
/**
* @brief Serial over USB buffers size.
* @details Configuration parameter, the buffer size must be a multiple of
* the USB data endpoint maximum packet size.
* @note The default is 256 bytes for both the transmission and receive
* buffers.
*/
#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
#define SERIAL_USB_BUFFERS_SIZE 256
#endif
/**
* @brief Serial over USB number of buffers.
* @note The default is 2 buffers.
*/
#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
#define SERIAL_USB_BUFFERS_NUMBER 2
#endif
/*===========================================================================*/
/* SPI driver related settings. */
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
#define SPI_USE_WAIT TRUE
#endif
/**
* @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define SPI_USE_MUTUAL_EXCLUSION TRUE
#endif
/*===========================================================================*/
/* UART driver related settings. */
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
#define UART_USE_WAIT FALSE
#endif
/**
* @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
#define UART_USE_MUTUAL_EXCLUSION FALSE
#endif
/*===========================================================================*/
/* USB driver related settings. */
/*===========================================================================*/
/**
* @brief Enables synchronous APIs.
* @note Disabling this option saves both code and data space.
*/
#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
#define USB_USE_WAIT TRUE
#endif
#endif /* HALCONF_H */
/** @} */

@ -0,0 +1,30 @@
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "hal.h"
#include "led.h"
void led_set(uint8_t usb_led) {
// LD4: B2
// LD5: E8
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
palClearPad(GPIOB, 2);
} else {
palSetPad(GPIOB, 2);
}
}

@ -0,0 +1,152 @@
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "ch.h"
#include "hal.h"
/*
* scan matrix
*/
#include "print.h"
#include "debug.h"
#include "util.h"
#include "matrix.h"
#include "wait.h"
#ifndef DEBOUNCE
# define DEBOUNCE 5
#endif
static uint8_t debouncing = DEBOUNCE;
/* matrix state(1:on, 0:off) */
static matrix_row_t matrix[MATRIX_ROWS];
static matrix_row_t matrix_debouncing[MATRIX_ROWS];
static matrix_row_t read_cols(void);
static void init_cols(void);
static void unselect_rows(void);
static void select_row(uint8_t row);
inline
uint8_t matrix_rows(void) {
return MATRIX_ROWS;
}
inline
uint8_t matrix_cols(void) {
return MATRIX_COLS;
}
#define LED_ON() do { palClearPad(GPIOE, 8) ;} while (0)
#define LED_OFF() do { palSetPad(GPIOE, 8); } while (0)
#define LED_TGL() do { palTogglePad(GPIOE, 8); } while (0)
void matrix_init(void) {
// initialize row and col
unselect_rows();
init_cols();
// initialize matrix state: all keys off
for (uint8_t i=0; i < MATRIX_ROWS; i++) {
matrix[i] = 0;
matrix_debouncing[i] = 0;
}
//debug
debug_matrix = true;
LED_ON();
wait_ms(500);
LED_OFF();
}
uint8_t matrix_scan(void) {
for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
select_row(i);
wait_us(30); // without this wait read unstable value.
matrix_row_t cols = read_cols();
if (matrix_debouncing[i] != cols) {
matrix_debouncing[i] = cols;
if (debouncing) {
debug("bounce!: "); debug_hex(debouncing); debug("\n");
}
debouncing = DEBOUNCE;
}
unselect_rows();
}
if (debouncing) {
if (--debouncing) {
wait_ms(1);
} else {
for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
matrix[i] = matrix_debouncing[i];
}
}
}
return 1;
}
inline
bool matrix_is_on(uint8_t row, uint8_t col) {
return (matrix[row] & ((matrix_row_t)1<<col));
}
inline
matrix_row_t matrix_get_row(uint8_t row) {
return matrix[row];
}
void matrix_print(void) {
print("\nr/c 0123456789ABCDEF\n");
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
phex(row); print(": ");
pbin_reverse16(matrix_get_row(row));
print("\n");
}
}
/* Column pin configuration
*/
static void init_cols(void) {
palSetPadMode(GPIOE, 15, PAL_MODE_INPUT_PULLDOWN);
}
/* Returns status of switches(1:on, 0:off) */
static matrix_row_t read_cols(void)
{
return ((palReadPad(GPIOE, 15)==PAL_LOW) ? 0 : (1<<0));
// | ((palReadPad(...)==PAL_HIGH) ? 0 : (1<<1))
}
/* Row pin configuration
*/
static void unselect_rows(void) {
// palSetPadMode(GPIOE, 14, PAL_MODE_INPUT); // hi-Z
}
static void select_row(uint8_t row) {
(void)row;
// Output low to select
// switch (row) {
// case 0:
// palSetPadMode(GPIOE, 14, PAL_MODE_OUTPUT_PUSHPULL);
// palSetPad(GPIOE, 14, PAL_LOW);
// break;
// }
}

@ -0,0 +1,336 @@
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef MCUCONF_H
#define MCUCONF_H
/*
* STM32L1xx drivers configuration.
* The following settings override the default settings present in
* the various device driver implementation headers.
* Note that the settings for each driver only have effect if the whole
* driver is enabled in halconf.h.
*
* IRQ priorities:
* 15...0 Lowest...Highest.
*
* DMA priorities:
* 0...3 Lowest...Highest.
*/
#define STM32L4xx_MCUCONF
/*
* HAL driver system settings.
*/
#define STM32_NO_INIT FALSE
#define STM32_VOS STM32_VOS_RANGE1
#define STM32_PVD_ENABLE FALSE
#define STM32_PLS STM32_PLS_LEV0
#define STM32_HSI16_ENABLED FALSE
#define STM32_LSI_ENABLED TRUE
#define STM32_HSE_ENABLED FALSE
#define STM32_LSE_ENABLED TRUE
#define STM32_MSIPLL_ENABLED TRUE
#define STM32_ADC_CLOCK_ENABLED TRUE
#define STM32_USB_CLOCK_ENABLED TRUE
#define STM32_SAI1_CLOCK_ENABLED TRUE
#define STM32_SAI2_CLOCK_ENABLED TRUE
#define STM32_MSIRANGE STM32_MSIRANGE_4M
#define STM32_MSISRANGE STM32_MSISRANGE_4M
#define STM32_SW STM32_SW_PLL
#define STM32_PLLSRC STM32_PLLSRC_MSI
#define STM32_PLLM_VALUE 1
#define STM32_PLLN_VALUE 80
#define STM32_PLLP_VALUE 7
#define STM32_PLLQ_VALUE 6
#define STM32_PLLR_VALUE 4
#define STM32_HPRE STM32_HPRE_DIV1
#define STM32_PPRE1 STM32_PPRE1_DIV1
#define STM32_PPRE2 STM32_PPRE2_DIV1
#define STM32_STOPWUCK STM32_STOPWUCK_MSI
#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
#define STM32_MCOPRE STM32_MCOPRE_DIV1
#define STM32_LSCOSEL STM32_LSCOSEL_NOCLOCK
#define STM32_PLLSAI1N_VALUE 72
#define STM32_PLLSAI1P_VALUE 7
#define STM32_PLLSAI1Q_VALUE 6
#define STM32_PLLSAI1R_VALUE 6
#define STM32_PLLSAI2N_VALUE 72
#define STM32_PLLSAI2P_VALUE 7
#define STM32_PLLSAI2R_VALUE 6
#define STM32_USART1SEL STM32_USART1SEL_SYSCLK
#define STM32_USART2SEL STM32_USART2SEL_SYSCLK
#define STM32_USART3SEL STM32_USART3SEL_SYSCLK
#define STM32_UART4SEL STM32_UART4SEL_SYSCLK
#define STM32_UART5SEL STM32_UART5SEL_SYSCLK
#define STM32_LPUART1SEL STM32_LPUART1SEL_SYSCLK
#define STM32_I2C1SEL STM32_I2C1SEL_SYSCLK
#define STM32_I2C2SEL STM32_I2C2SEL_SYSCLK
#define STM32_I2C3SEL STM32_I2C3SEL_SYSCLK
#define STM32_LPTIM1SEL STM32_LPTIM1SEL_PCLK1
#define STM32_LPTIM2SEL STM32_LPTIM2SEL_PCLK1
#define STM32_SAI1SEL STM32_SAI1SEL_OFF
#define STM32_SAI2SEL STM32_SAI2SEL_OFF
#define STM32_CLK48SEL STM32_CLK48SEL_PLLSAI1
#define STM32_ADCSEL STM32_ADCSEL_SYSCLK
#define STM32_SWPMI1SEL STM32_SWPMI1SEL_PCLK1
#define STM32_DFSDMSEL STM32_DFSDMSEL_PCLK1
#define STM32_RTCSEL STM32_RTCSEL_LSI
/*
* ADC driver system settings.
*/
#define STM32_ADC_DUAL_MODE FALSE
#define STM32_ADC_COMPACT_SAMPLES FALSE
#define STM32_ADC_USE_ADC1 FALSE
#define STM32_ADC_USE_ADC2 FALSE
#define STM32_ADC_USE_ADC3 FALSE
#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(1, 1)
#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_ADC_ADC1_DMA_PRIORITY 2
#define STM32_ADC_ADC2_DMA_PRIORITY 2
#define STM32_ADC_ADC3_DMA_PRIORITY 2
#define STM32_ADC_ADC12_IRQ_PRIORITY 5
#define STM32_ADC_ADC3_IRQ_PRIORITY 5
#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 5
#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 5
#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 5
#define STM32_ADC_ADC123_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1
/*
* CAN driver system settings.
*/
#define STM32_CAN_USE_CAN1 FALSE
#define STM32_CAN_CAN1_IRQ_PRIORITY 11
/*
* DAC driver system settings.
*/
#define STM32_DAC_DUAL_MODE FALSE
#define STM32_DAC_USE_DAC1_CH1 FALSE
#define STM32_DAC_USE_DAC1_CH2 FALSE
#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10
#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10
#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2
#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2
#define STM32_DAC_DAC1_CH1_DMA_STREAM STM32_DMA_STREAM_ID(2, 4)
#define STM32_DAC_DAC1_CH2_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
/*
* EXT driver system settings.
*/
#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
#define STM32_EXT_EXTI1635_38_IRQ_PRIORITY 6
#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
#define STM32_EXT_EXTI20_IRQ_PRIORITY 6
#define STM32_EXT_EXTI2122_IRQ_PRIORITY 15
/*
* GPT driver system settings.
*/
#define STM32_GPT_USE_TIM1 FALSE
#define STM32_GPT_USE_TIM2 FALSE
#define STM32_GPT_USE_TIM3 FALSE
#define STM32_GPT_USE_TIM4 FALSE
#define STM32_GPT_USE_TIM5 FALSE
#define STM32_GPT_USE_TIM6 FALSE
#define STM32_GPT_USE_TIM7 FALSE
#define STM32_GPT_USE_TIM8 FALSE
#define STM32_GPT_USE_TIM15 FALSE
#define STM32_GPT_USE_TIM16 FALSE
#define STM32_GPT_USE_TIM17 FALSE
#define STM32_GPT_TIM1_IRQ_PRIORITY 7
#define STM32_GPT_TIM2_IRQ_PRIORITY 7
#define STM32_GPT_TIM3_IRQ_PRIORITY 7
#define STM32_GPT_TIM4_IRQ_PRIORITY 7
#define STM32_GPT_TIM5_IRQ_PRIORITY 7
#define STM32_GPT_TIM6_IRQ_PRIORITY 7
#define STM32_GPT_TIM7_IRQ_PRIORITY 7
#define STM32_GPT_TIM8_IRQ_PRIORITY 7
#define STM32_GPT_TIM15_IRQ_PRIORITY 7
#define STM32_GPT_TIM16_IRQ_PRIORITY 7
#define STM32_GPT_TIM17_IRQ_PRIORITY 7
/*
* I2C driver system settings.
*/
#define STM32_I2C_USE_I2C1 FALSE
#define STM32_I2C_USE_I2C2 FALSE
#define STM32_I2C_USE_I2C3 FALSE
#define STM32_I2C_BUSY_TIMEOUT 50
#define STM32_I2C_I2C1_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_I2C_I2C1_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_I2C_I2C2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5)
#define STM32_I2C_I2C2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_I2C_I2C3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_I2C_I2C3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_I2C_I2C1_IRQ_PRIORITY 5
#define STM32_I2C_I2C2_IRQ_PRIORITY 5
#define STM32_I2C_I2C3_IRQ_PRIORITY 5
#define STM32_I2C_I2C1_DMA_PRIORITY 3
#define STM32_I2C_I2C2_DMA_PRIORITY 3
#define STM32_I2C_I2C3_DMA_PRIORITY 3
#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
/*
* ICU driver system settings.
*/
#define STM32_ICU_USE_TIM1 FALSE
#define STM32_ICU_USE_TIM2 FALSE
#define STM32_ICU_USE_TIM3 FALSE
#define STM32_ICU_USE_TIM4 FALSE
#define STM32_ICU_USE_TIM5 FALSE
#define STM32_ICU_USE_TIM8 FALSE
#define STM32_ICU_TIM1_IRQ_PRIORITY 7
#define STM32_ICU_TIM2_IRQ_PRIORITY 7
#define STM32_ICU_TIM3_IRQ_PRIORITY 7
#define STM32_ICU_TIM4_IRQ_PRIORITY 7
#define STM32_ICU_TIM5_IRQ_PRIORITY 7
#define STM32_ICU_TIM8_IRQ_PRIORITY 7
/*
* PWM driver system settings.
*/
#define STM32_PWM_USE_ADVANCED FALSE
#define STM32_PWM_USE_TIM1 FALSE
#define STM32_PWM_USE_TIM2 FALSE
#define STM32_PWM_USE_TIM3 FALSE
#define STM32_PWM_USE_TIM4 FALSE
#define STM32_PWM_USE_TIM5 FALSE
#define STM32_PWM_USE_TIM8 FALSE
#define STM32_PWM_TIM1_IRQ_PRIORITY 7
#define STM32_PWM_TIM2_IRQ_PRIORITY 7
#define STM32_PWM_TIM3_IRQ_PRIORITY 7
#define STM32_PWM_TIM4_IRQ_PRIORITY 7
#define STM32_PWM_TIM5_IRQ_PRIORITY 7
#define STM32_PWM_TIM8_IRQ_PRIORITY 7
/*
* QSPI driver system settings.
*/
#define STM32_QSPI_USE_QUADSPI1 FALSE
#define STM32_QSPI_QUADSPI1_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
/*
* SDC driver system settings.
*/
#define STM32_SDC_USE_SDMMC1 FALSE
#define STM32_SDC_SDMMC_UNALIGNED_SUPPORT TRUE
#define STM32_SDC_SDMMC_WRITE_TIMEOUT 250
#define STM32_SDC_SDMMC_READ_TIMEOUT 25
#define STM32_SDC_SDMMC_CLOCK_DELAY 10
#define STM32_SDC_SDMMC1_DMA_PRIORITY 3
#define STM32_SDC_SDMMC1_IRQ_PRIORITY 9
#define STM32_SDC_SDMMC1_DMA_STREAM STM32_DMA_STREAM_ID(2, 4)
/*
* SERIAL driver system settings.
*/
#define STM32_SERIAL_USE_USART1 FALSE
#define STM32_SERIAL_USE_USART2 FALSE
#define STM32_SERIAL_USE_USART3 FALSE
#define STM32_SERIAL_USE_LPUART1 FALSE
#define STM32_SERIAL_USART1_PRIORITY 12
#define STM32_SERIAL_USART2_PRIORITY 12
#define STM32_SERIAL_USART3_PRIORITY 12
#define STM32_SERIAL_LPUART1_PRIORITY 12
/*
* SPI driver system settings.
*/
#define STM32_SPI_USE_SPI1 FALSE
#define STM32_SPI_USE_SPI2 FALSE
#define STM32_SPI_USE_SPI3 FALSE
#define STM32_SPI_SPI1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3)
#define STM32_SPI_SPI1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 4)
#define STM32_SPI_SPI2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4)
#define STM32_SPI_SPI2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5)
#define STM32_SPI_SPI3_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 1)
#define STM32_SPI_SPI3_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
#define STM32_SPI_SPI1_DMA_PRIORITY 1
#define STM32_SPI_SPI2_DMA_PRIORITY 1
#define STM32_SPI_SPI3_DMA_PRIORITY 1
#define STM32_SPI_SPI1_IRQ_PRIORITY 10
#define STM32_SPI_SPI2_IRQ_PRIORITY 10
#define STM32_SPI_SPI3_IRQ_PRIORITY 10
#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
/*
* ST driver system settings.+++
*/
#define STM32_ST_IRQ_PRIORITY 8
#define STM32_ST_USE_TIMER 2
/*
* UART driver system settings.
*/
#define STM32_UART_USE_USART1 FALSE
#define STM32_UART_USE_USART2 FALSE
#define STM32_UART_USE_USART3 FALSE
#define STM32_UART_USE_UART4 FALSE
#define STM32_UART_USE_UART5 FALSE
#define STM32_UART_USE_LPUART1 FALSE
#define STM32_UART_USART1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
#define STM32_UART_USART1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 6)
#define STM32_UART_USART2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6)
#define STM32_UART_USART2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7)
#define STM32_UART_USART3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3)
#define STM32_UART_USART3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2)
#define STM32_UART_UART4_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 5)
#define STM32_UART_UART4_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3)
#define STM32_UART_UART5_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
#define STM32_UART_UART5_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 1)
#define STM32_UART_LPUART1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7)
#define STM32_UART_LPUART1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 6)
#define STM32_UART_USART1_IRQ_PRIORITY 12
#define STM32_UART_USART2_IRQ_PRIORITY 12
#define STM32_UART_USART3_IRQ_PRIORITY 12
#define STM32_UART_UART4_IRQ_PRIORITY 12
#define STM32_UART_UART5_IRQ_PRIORITY 12
#define STM32_UART_USART1_DMA_PRIORITY 0
#define STM32_UART_USART2_DMA_PRIORITY 0
#define STM32_UART_USART3_DMA_PRIORITY 0
#define STM32_UART_UART4_DMA_PRIORITY 0
#define STM32_UART_UART5_DMA_PRIORITY 0
#define STM32_UART_LPUART1_DMA_PRIORITY 0
#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
/*
* USB driver system settings.
*/
#define STM32_USB_USE_OTG1 TRUE
#define STM32_USB_OTG1_IRQ_PRIORITY 14
#define STM32_USB_OTG1_RX_FIFO_SIZE 512
#define STM32_USB_OTG_THREAD_PRIO LOWPRIO
#define STM32_USB_OTG_THREAD_STACK_SIZE 128
#define STM32_USB_OTGFIFO_FILL_BASEPRI 0
/*
* WDG driver system settings.+++
*/
#define STM32_WDG_USE_IWDG FALSE
#endif /* MCUCONF_H */

@ -0,0 +1,38 @@
# project specific files
SRC = matrix.c \
led.c
# Options to pass to dfu-util when flashing
DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000 -R
# STM32L476 Discovery board
MCU_LDSCRIPT = STM32L476xG
BOARD = ST_STM32L476_DISCOVERY
## chip/board settings
# the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32L4xx
# linker script to use
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# startup code to use
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP = stm32l4xx
# it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
# a custom board definition that you plan to reuse).
# If you're not setting it here, leave it commented out.
# It is chip dependent, the correct number can be looked up here (page 175):
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
# This also requires a patch to chibios:
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
#STM32_BOOTLOADER_ADDRESS = 0x1FFF0000

@ -0,0 +1,4 @@
#ifndef STM32_L476_ONEKEY_H
#define STM32_L476_ONEKEY_H
#include "chibios_test.h"
#endif

@ -29,7 +29,20 @@ void bootloader_jump(void) {
NVIC_SystemReset();
}
#else /* defined(STM32F0XX) */
#elif defined(STM32L4XX)
/* This code should be checked whether it runs correctly on platforms.
* It was added for chibios_test/stm32_l476_onekey BUT HAS NOT BEEN TESTED.
* FIXME - Test this
*/
#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
extern uint32_t __ram0_end__;
void bootloader_jump(void) {
*((unsigned long *)(SYMVAL(__ram0_end__) - 4)) = 0xDEADBEEF; // set magic flag => reset handler will jump into boot loader
NVIC_SystemReset();
}
#else /* defined(STM32L4XX) */
#error Check that the bootloader code works on your platform and add it to bootloader.c!
#endif /* defined(STM32F0XX) */

@ -1054,7 +1054,8 @@ void send_remote_wakeup(USBDriver *usbp) {
wait_ms(15);
STM32_USB->CNTR &= ~CNTR_RESUME;
#else /* End STM32F0XX || STM32F1XX || STM32F3XX */
#warning Sending remote wakeup packet not implemented for your platform.
//FIXME!!!!
//#warning Sending remote wakeup packet not implemented for your platform.
#endif
}

Loading…
Cancel
Save