/** \file * * This file contains special DoxyGen information for the generation of the main page and other special * documentation pages. It is not a project source file. */ /** \mainpage Benito Arduino Programmer Project * * \section Sec_Compat Project Compatibility: * * The following list indicates what microcontrollers are compatible with this project. * * \li Series 7 USB AVRs (AT90USBxxx7) * \li Series 6 USB AVRs (AT90USBxxx6) * \li Series 4 USB AVRs (ATMEGAxxU4) * \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) * * \section Sec_Info USB Information: * * The following table gives a rundown of the USB utilization of this project. * * <table> * <tr> * <td><b>USB Mode:</b></td> * <td>Device</td> * </tr> * <tr> * <td><b>USB Class:</b></td> * <td>Communications Device Class (CDC)</td> * </tr> * <tr> * <td><b>USB Subclass:</b></td> * <td>Abstract Control Model (ACM)</td> * </tr> * <tr> * <td><b>Relevant Standards:</b></td> * <td>USBIF CDC Class Standard \n * Arduino Bootloader Specification</td> * </tr> * <tr> * <td><b>Supported USB Speeds:</b></td> * <td>Full Speed Mode</td> * </tr> * </table> * * \section Sec_Description Project Description: * * Firmware for a USB AVR powered programmer for Arduino boards using the official Arduino bootloader. This * project acts like a regular USB to Serial bridge, except that asserting the DTR line will cause a pulse * to appear on a given port pin, to control the target's /RESET pin. * * This is primarily designed to fit the Benito board from www.dorkbotpdx.org, but will suit all USB AVRs. * * After running this project for the first time on a new computer, you will need to supply the .INF file located * in this project's directory as the device's driver when running under Windows. This will enable Windows to use * its inbuilt CDC drivers, negating the need for custom drivers for the device. Other Operating Systems should * automatically use their own inbuilt CDC-ACM drivers. * * \section Sec_Options Project Options * * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. * * <table> * <tr> * <td><b>Define Name:</b></td> * <td><b>Location:</b></td> * <td><b>Description:</b></td> * </tr> * <tr> * <td>AVR_RESET_LINE_PORT</td> * <td>AppConfig.h</td> * <td>Indicates the PORT register of the pin used to generate the target /RESET line pulse.</td> * </tr> * <tr> * <td>AVR_RESET_LINE_DDR</td> * <td>AppConfig.h</td> * <td>Indicates the DDR register of the pin used to generate the target /RESET line pulse.</td> * </tr> * <tr> * <td>AVR_RESET_LINE_MASK</td> * <td>AppConfig.h</td> * <td>Indicates the mask of the pin used to generate the target /RESET line pulse.</td> * </tr> * <tr> * <td>AVR_RESET_PULSE_MS</td> * <td>AppConfig.h</td> * <td>Pulse length in milliseconds for the target /RESET pulse.</td> * </tr> * <tr> * <td>TX_RX_LED_PULSE_MS</td> * <td>AppConfig.h</td> * <td>Pulse length in milliseconds for the activity Tx/Rx LEDs.</td> * </tr> * <tr> * <td>PING_PONG_LED_PULSE_MS</td> * <td>AppConfig.h</td> * <td>Pulse length in milliseconds for the enumeration LED ping-ponging between toggles.</td> * </tr> * <tr> * <td>RECEIVE_BUFFER_FLUSH_MS</td> * <td>AppConfig.h</td> * <td>Period between flushings of received data buffer to the attached USB host.</td> * </tr> * </table> */