/** \file * * This file contains special DoxyGen information for the generation of the main page and other special * documentation pages. It is not a project source file. */ /** \mainpage AVRISP MKII Programmer Project * * \section Sec_Compat Project Compatibility * * The following list indicates what microcontrollers are compatible with this project. * * \li Series 7 USB AVRs (AT90USBxxx7) * \li Series 6 USB AVRs (AT90USBxxx6) * \li Series 4 USB AVRs (ATMEGAxxU4) * \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - 8KB versions with reduced features only * * \section Sec_Info USB Information * * The following table gives a rundown of the USB utilization of this project. * * * * * * * * * * * * * * * * * * * * * * *
USB Mode:Device
USB Class:Vendor Specific Class
USB Subclass:N/A
Relevant Standards:Atmel AVRISP MKII Protocol Specification
Supported USB Speeds:Full Speed Mode
* * \section Sec_Description Project Description * * Firmware for an Atmel Studio/AVR Studio compatible AVRISP-MKII clone programmer. This project will enable the USB * AVR series of microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within * Atmel Studio/AVR Studio or with any software capable of driving a real Atmel AVRISP-MKII programmer. In its most * basic form, it allows for the programming of AVR TINY, MEGA and XMEGA devices aat the programmer's VCC voltage from * within Atmel Studio/AVR Studio with no special hardware other than the USB AVR and the parts needed for the USB * interface. If the user desires, more advanced circuits incorporating level conversion can be made to allow for the * programming of target AVRs running at a different voltage to the programmer. * * This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII * drivers. When prompted, direct your OS to install Atmel's AVRISP-MKII drivers provided with Atmel Studio/AVR Studio. * * Note that this design currently has the following limitations: * - No reversed/shorted target connector detection and notification * - A separate header is required for each of the ISP, PDI and TPI programming protocols that the user wishes to use * * On AVR models with an ADC converter, the USB AVR's AVCC pin should be tied to 5V (e.g. VBUS) and the * \c VTARGET_ADC_CHANNEL token should be set to an appropriate ADC channel number in the project makefile for VTARGET * detection to operate correctly. On models without an ADC converter, VTARGET will report a fixed 3.3V level at all times * which should allow the programmer to remain compatible at the protocol level with all AVR devices. * * While this application can be compiled for USB AVRs with as little as 8KB of FLASH, for full functionality 16KB or more * of FLASH is required. On 8KB devices, ISP or PDI/TPI protocol programming support can be disabled to reduce program size. * * \section Sec_KnownIssues Known Issues: * * \par Incompatible with newer AVRDUDE releases. * Due to a change in 6.0.1 and never AVRDUDE releases, * these builds are incompatible with the AVRISP-MKII clone project. Use an older 5.x release until AVRDUDE is patched. * * \par XMEGA EEPROM programming fails in some cases. * Several users have reported that XMEGA EEPROM programming fails unless the chip is erased first. If a non-blank EEPROM * is present, writing further EEPROM data causes corruption. * LUFA issue tracker entry. * * \par Does not work with Atmel Studio 6.2 or newer in some cases. * If the libUSB filter driver is used to bind both libUSB and Jungo drivers to the clone device at the same time, it will * no longer work in Atmel Studio 6.2 and newer. This is due to a change in the latter; Atmel Studio now supports both * drivers for various tools, but while the libUSB driver is given preference the inner workings of Atmel Studio cannot * communicate with the AVR-ISP MKII with libUSB (this is true for the genuine tool also). Uninstall the filter driver and * install only the standard libUSB driver, or Jungo driver. The \c RESET_TOGGLES_LIBUSB_COMPAT compile option (detailed * below) is a suitable workaround to this issue. * * \section Sec_Installation Installation * The programmer supports multiple platforms, both Windows and Linux. * * \subsection SSec_LinuxInstallation Linux Installation * On Linux systems, the programmer should be usable out of the box with no special setup other than (on some systems) * editing of the system permissions to allow the programmer to be used from a non-elevated (root) context. The programmer * is compatible with the free open source AVRDude programming software project. * * \subsection SSec_WindowsInstallation Windows Installation * On Windows systems, due to an unfortunate limitation of the USB AVR devices and the driver used in the official AVR * Studio/Atmel Studio platform, the programmer cannot be made compatible with AVRDude and AVR Studio/Atmel Studio at the * same time. Instead, the programmer will be compatible with the official Atmel software by default, with a recompilation * with the \c LIBUSB_DRIVER_COMPAT token (see \ref Sec_Options) being required to use the alternative libUSB driver * compatibility mode that will allow the programmer to work under AVRDude on Windows. * * If compiled for Atmel Studio/AVR Studio compatibility, install the Jungo device drivers that ship with the Atmel software. * If compiled in the alternative libUSB compatibility mode for AVRDude use, install the libUSB drivers that are included * with your compiled copy of AVRDude, or create them using the libUSB-Win32 (http://sourceforge.net/projects/libusb-win32) * project. * * For convenience, the programmer will report two different serial numbers depending on the firmware compatibility mode, so * that the correct driver can be installed for the matching firmware. If the \c RESET_TOGGLES_LIBUSB_COMPAT compile option * is used (see \ref Sec_Options) this allows for an easy way to automatically switch device drivers along with the firmware * compatibility mode. The serials are: * * * * * * * * * * * * * * *
Serial Number:Compatibility Mode:
000200012345Jungo (Atmel Studio) Compatibility
000200112345libUSB Compatibility
* * \section Sec_ISP ISP Connections * Connections to the device for SPI programming (when enabled): * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Programmer Pin:Target Device Pin:ISP 6 Pin Layout:
MISOPDO1
ADCx 1VTARGET2
SCLKSCLK3
MOSIPDI4
PORTx.y 2/RESET5
GNDGND6
* * In addition, the AVR's OCR1A pin will generate a 4MHz clock, to act as an external rescue device clock if the * fuses have been mis-set. To use the recovery clock, connect the OCR1A pin of the USB AVR to the target AVR's * XTAL1 pin, and set the ISP programming speed to 125KHz (note: other ISP speeds will not work correctly). * * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n * 2 See AUX line related tokens in the \ref Sec_Options section * * \section Sec_PDI PDI Connections * Connections to the device for PDI programming (when enabled): * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Programmer Pin:Target Device Pin:PDI 6 Pin Layout:
Tx/Rx 2DATA1
ADCx 1VTARGET2
N/AN/A3
N/AN/A4
XCKCLOCK5
GNDGND6
* * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n * * \section Sec_TPI TPI Connections * Connections to the device for TPI programming (when enabled): * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Programmer Pin:Target Device Pin:TPI 6 Pin Layout:
Tx/Rx 2DATA1
ADCx 1VTARGET2
XCK 2CLOCK3
N/AN/A4
PORTx.y 3/RESET5
GNDGND6
* * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n * 3 See AUX line related tokens in the \ref Sec_Options section * * \section Sec_Options Project Options * * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Define Name:Location:Description:
AUX_LINE_PORTAppConfig.hPORT register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n Ignored when compiled for the XPLAIN board.
AUX_LINE_PINAppConfig.hPIN register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n Ignored when compiled for the XPLAIN board.
AUX_LINE_DDRAppConfig.hDDR register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n Ignored when compiled for the XPLAIN board.
AUX_LINE_MASKAppConfig.hMask for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. Must not be the AVR's /SS pin. * \n \n Ignored when compiled for the XPLAIN board.
VTARGET_ADC_CHANNELAppConfig.hADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined. * \n \n Ignored when compiled for targets lacking an ADC.
ENABLE_ISP_PROTOCOLAppConfig.hDefine to enable SPI programming protocol support. * \n \n Ignored when compiled for the XPLAIN board.
ENABLE_XPROG_PROTOCOLAppConfig.hDefine to enable PDI and TPI programming protocol support. * \n \n Ignored when compiled for the XPLAIN board.
NO_VTARGET_DETECTAppConfig.hDefine to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer * to report a fixed 3.3V target voltage to the host regardless of the real target voltage. * \n \n Ignored when compiled for targets lacking an ADC.
VTARGET_REF_VOLTSAppConfig.hIndicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply * voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage * to the ADC. * \n \n Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.
VTARGET_USE_INTERNAL_REFAppConfig.hSelects the internal 2.56V ADC reference voltage, instead of using the AVR's VREF pin. When enabled, this option will * override the VTARGET_REF_VOLTS configuration option. * \n \n Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.
VTARGET_SCALE_FACTORAppConfig.hIndicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the * ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be * measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set * to 2. * \n \n Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.
LIBUSB_DRIVER_COMPATAppConfig.hDefine to switch to a non-standard endpoint scheme, breaking compatibility with Atmel Studio/AVR Studio under Windows but * making the code compatible with software such as avrdude (all platforms) that use the libUSB driver. * * \note This option is incompatible with \c RESET_TOGGLES_LIBUSB_COMPAT.
RESET_TOGGLES_LIBUSB_COMPATAppConfig.hDefine to make the /RESET line of the AVR toggle between Jungo and libUSB driver compatibility modes. Each time the AVR is * reset externally via the reset pin, the compatibility mode will be toggled. The compatibility mode is preserved between * power cycles and is not toggled via other forms of reset such as Watchdog or Brown Out. * * When this option is enabled, all board LEDs will flash twice on startup for Jungo compatibility mode, and five times for * libUSB compatibility mode. * * \note This option is incompatible with \c LIBUSB_DRIVER_COMPAT.
XCK_RESCUE_CLOCK_ENABLEAppConfig.hDefine to move the ISP rescue clock to the AVR's XCK pin instead of the OCR1A output pin. This is useful for existing programming * hardware that does not expose the OCR1A pin of the AVR, but may cause some issues with PDI programming mode.
INVERTED_ISP_MISOAppConfig.hDefine to invert the received data on the ISP MISO line. This is sometimes needed depending on the level translation hardware used, * if the translator hardware inverts the received logic level.
FIRMWARE_VERSION_MINORAppConfig.hDefine to set the minor firmware revision nunber reported to the host on request. By default this will use a firmware version compatible * with the latest Atmel IDE version, however if desired the reported minor value can be adjusted here.
*/