/** \file
 *
 *  This file contains special DoxyGen information for the generation of the main page and other special
 *  documentation pages. It is not a project source file.
 */
 
/** \mainpage XPLAIN UART Bridge/PDI Programmer Project
 *
 *  \section SSec_Compat Project Compatibility:
 *
 *  The following list indicates what microcontrollers are compatible with this project.
 *
 *  - AT90USB1287
 *
 *  \section SSec_Info USB Information:
 *
 *  The following table gives a rundown of the USB utilization of this project.
 *
 *  <table>
 *   <tr>
 *    <td><b>USB Mode:</b></td>
 *    <td>1) Device</td>
 *    <td>2) Device</td>
 *   </tr>
 *   <tr>
 *    <td><b>USB Class:</b></td>
 *    <td>1) Communications Device Class (CDC)</td>
 *    <td>2) Vendor Specific Class</td>
 *   </tr>
 *   <tr> 
 *    <td><b>USB Subclass:</b></td>
 *    <td>1) Abstract Control Model (ACM)</td>
 *    <td>2) N/A</td>
 *   </tr>
 *   <tr>
 *    <td><b>Relevant Standards:</b></td>
 *    <td>1) USBIF CDC Class Standard</td>
 *    <td>2) Atmel AVRISP MKII Protocol Specification</td>
 *   </tr>
 *   <tr>
 *    <td><b>Usable Speeds:</b></td>
 *    <td>1) Full Speed Mode</td>
 *    <td>2) Full Speed Mode</td>
 *   </tr>
 *  </table>
 *
 *  \section SSec_Description Project Description: 
 *
 *  This project serves a dual purpose. When loaded into the USB AVR on the XPLAIN board, it will act as either a USB to Serial
 *  converter for the XPLAIN's hardware USART (at a speed of 9600 baud), or an AVRStudio compaible PDI programmer for the XMEGA.
 *  This project replaces the firmware preloaded onto the XPLAIN's onboard AT90USB1287 microcontroller.
 *
 *  When power to the board is applied, the TDI pin (pin 9) of the USB AVR's JTAG port is read. If the pin is left high, the device
 *  will enumerate as a regular COM port on the host, which can then be opened and data exchanged between the XMEGA and Host as if
 *  the XMEGA was connected directly to the host's serial port. If the pin is pulled low by shorting it to GND (pin 10), the device
 *  will enumerate as an AVRISP-MKII to the host, so that the XMEGA can be reprogrammed by AVRStudio or other compatible software
 *  such as avrdude.
 *
 *  After running this project for the first time on a new computer, you will need to supply the .INF file located in this project
 *  project's directory as the device's driver when running under Windows. This will enable Windows to use its inbuilt CDC drivers,
 *  negating the need for custom drivers for the device. Other Operating Systems should automatically use their own inbuilt CDC-ACM
 *  drivers.
 *
 *  This project relies on files from the LUFA AVRISP-MKII project for compilation.
 *
 *  \section SSec_Options Project Options
 *
 *  The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
 *
 *  <table>
 *   <tr>
 *    <td><b>Define Name:</b></td>
 *    <td><b>Location:</b></td>
 *    <td><b>Description:</b></td>
 *   </tr>
 *   <tr>
 *    <td>BUFF_STATICSIZE</td>
 *    <td>RingBuff.h</td>
 *    <td>Defines the maximum number of bytes which can be buffered in each Ring Buffer.</td>
 *   </tr>
 *   <tr>
 *    <td>WIN_LIBUSB_COMPAT</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making
 *        the code compatible with Windows builds of avrdude using the libUSB driver. Linux platforms are not affected by this
 *        option.
 *   </tr>
 *  </table>
 */