You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
125 lines
4.5 KiB
125 lines
4.5 KiB
#----------------------------------------------------------------------------
|
|
# On command line:
|
|
#
|
|
# make all = Make software.
|
|
#
|
|
# make clean = Clean out built project files.
|
|
#
|
|
# make coff = Convert ELF to AVR COFF.
|
|
#
|
|
# make extcoff = Convert ELF to AVR Extended COFF.
|
|
#
|
|
# make program = Download the hex file to the device.
|
|
# Please customize your programmer settings(PROGRAM_CMD)
|
|
#
|
|
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
|
# (must have teensy_loader_cli installed).
|
|
#
|
|
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
|
# have dfu-programmer installed).
|
|
#
|
|
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
|
# have Atmel FLIP installed).
|
|
#
|
|
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
|
# (must have dfu-programmer installed).
|
|
#
|
|
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
|
# (must have Atmel FLIP installed).
|
|
#
|
|
# make debug = Start either simulavr or avarice as specified for debugging,
|
|
# with avr-gdb or avr-insight as the front end for debugging.
|
|
#
|
|
# make filename.s = Just compile filename.c into the assembler code only.
|
|
#
|
|
# make filename.i = Create a preprocessed source file for use in submitting
|
|
# bug reports to the GCC project.
|
|
#
|
|
# To rebuild project do "make clean" then "make all".
|
|
#----------------------------------------------------------------------------
|
|
|
|
ifdef TEENSY2
|
|
OPT_DEFS += -DATREUS_TEENSY2
|
|
ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
|
|
else
|
|
OPT_DEFS += -DATREUS_ASTAR
|
|
ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
|
|
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
|
|
endif
|
|
|
|
# MCU name
|
|
#MCU = at90usb1287
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
|
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
|
|
NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA
|
|
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
|
|
# MIDI_ENABLE ?= YES # MIDI controls
|
|
UNICODE_ENABLE ?= YES # Unicode
|
|
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
|
|
|
|
|
ifndef QUANTUM_DIR
|
|
include ../../Makefile
|
|
endif
|
|
|
|
USB ?= /dev/cu.usbmodem1411
|
|
|
|
upload: build
|
|
$(ATRUES_UPLOAD_COMMAND)
|
|
|