You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
211 lines
6.9 KiB
211 lines
6.9 KiB
/** \file
|
|
*
|
|
* This file contains special DoxyGen information for the generation of the main page and other special
|
|
* documentation pages. It is not a project source file.
|
|
*/
|
|
|
|
/** \mainpage AVRISP MKII Programmer Project
|
|
*
|
|
* \section SSec_Compat Demo Compatibility:
|
|
*
|
|
* The following list indicates what microcontrollers are compatible with this demo.
|
|
*
|
|
* - Series 7 USB AVRs
|
|
* - Series 6 USB AVRs
|
|
* - Series 4 USB AVRs
|
|
* - Series 2 USB AVRs
|
|
*
|
|
* \section SSec_Info USB Information:
|
|
*
|
|
* The following table gives a rundown of the USB utilization of this demo.
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <td><b>USB Mode:</b></td>
|
|
* <td>Device</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>USB Class:</b></td>
|
|
* <td>Vendor Specific Class</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>USB Subclass:</b></td>
|
|
* <td>N/A</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>Relevant Standards:</b></td>
|
|
* <td>Atmel AVRISP MKII Protocol Specification</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>Usable Speeds:</b></td>
|
|
* <td>Full Speed Mode</td>
|
|
* </tr>
|
|
* </table>
|
|
*
|
|
* \section SSec_Description Project Description:
|
|
*
|
|
* Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
|
|
* microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
|
|
* most basic form, it allows for the programming of 5V AVRs from within AVRStudio with no special hardware other than
|
|
* the USB AVR and the parts needed for the USB interface. If the user desires, more advanced circuits incorporating
|
|
* level conversion can be made to allow for the programming of 3.3V AVR designs.
|
|
*
|
|
* This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII
|
|
* drivers. When promted, direct your OS to install Atmel's AVRISP-MKII drivers provided with AVRStudio.
|
|
*
|
|
* Note that this design currently has several limitations:
|
|
* - Minimum ISP target clock speed of 500KHz due to hardware SPI used
|
|
* - No reversed/shorted target connector detection and notification
|
|
*
|
|
* On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
|
|
* set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
|
|
* without an ADC converter, VTARGET will report at a fixed 5V level.
|
|
*
|
|
* When compiled for the XPLAIN board target, this will automatically configure itself for the correct connections to the
|
|
* XPLAIN's XMEGA AVR, and will enable only PDI programming support.
|
|
*
|
|
*
|
|
* Connections to the device for SPI programming (when enabled):
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <td><b>Programmer Pin:</b></td>
|
|
* <td><b>Target Device Pin:</b></td>
|
|
* <td><b>ISP 6 Pin Layout:</b></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>MISO</td>
|
|
* <td>PDO</td>
|
|
* <td>1</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>ADCx <b><sup>1</sup></b></td>
|
|
* <td>VTARGET</td>
|
|
* <td>2</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>SCLK</td>
|
|
* <td>SCLK</td>
|
|
* <td>3</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>MOSI</td>
|
|
* <td>PDI</td>
|
|
* <td>4</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>PORTx.y <b><sup>2</sup></b></td>
|
|
* <td>/RESET</td>
|
|
* <td>5</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>GND</td>
|
|
* <td>GND</td>
|
|
* <td>6</td>
|
|
* </tr>
|
|
* </table>
|
|
*
|
|
* <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
|
|
* <b><sup>2</sup></b> <i>See \ref SSec_Options section</i>
|
|
*
|
|
*
|
|
* Connections to the device for PDI programming<b><sup>1</sup></b> (when enabled):
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <td><b>Programmer Pin:</b></td>
|
|
* <td><b>Target Device Pin:</b></td>
|
|
* <td><b>PDI 6 Pin Layout:</b></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>MISO</td>
|
|
* <td>DATA</td>
|
|
* <td>1</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>ADCx <b><sup>1</sup></b></td>
|
|
* <td>VTARGET</td>
|
|
* <td>2</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>N/A</td>
|
|
* <td>N/A</td>
|
|
* <td>3</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>N/A</td>
|
|
* <td>N/A</td>
|
|
* <td>4</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>PORTx.y <b><sup>2</sup></b></td>
|
|
* <td>CLOCK</td>
|
|
* <td>5</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>GND</td>
|
|
* <td>GND</td>
|
|
* <td>6</td>
|
|
* </tr>
|
|
* </table>
|
|
*
|
|
* <b><sup>1</sup></b> When PDI_VIA_HARDWARE_USART is set, the AVR's Tx and Rx become the DATA line when connected together
|
|
* via a pair of 300 ohm resistors, and the AVR's XCK pin becomes CLOCK.
|
|
*
|
|
* \section SSec_Options Project Options
|
|
*
|
|
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <td><b>Define Name:</b></td>
|
|
* <td><b>Location:</b></td>
|
|
* <td><b>Description:</b></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>RESET_LINE_PORT</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>PORT register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>RESET_LINE_PIN</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>PIN register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>RESET_LINE_DDR</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>DDR register for the programmer's target RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>RESET_LINE_MASK</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>Mask for the programmer's target RESET line on the chosen port. <b>Must not be the AVR's /SS pin</b>, as the
|
|
* target pins are tri-stated when not in use, and low signals on the /SS pin will force SPI slave mode when the
|
|
* pin is configured as an input. When in PDI programming mode, this is the target clock pin.
|
|
* <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>VTARGET_ADC_CHANNEL</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection.</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>ENABLE_ISP_PROTOCOL</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>ENABLE_PDI_PROTOCOL</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>Define to enable XMEGA PDI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>PDI_VIA_HARDWARE_USART</td>
|
|
* <td>Makefile CDEFS</td>
|
|
* <td>Define to force the PDI protocol (when enabled) to use the hardware USART instead of bit-banging to match the official
|
|
* AVRISP pinout. <i>Automatically set when compiled for the XPLAIN board.</i></td>
|
|
* </tr>
|
|
* </table>
|
|
*/
|