You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
94 lines
2.1 KiB
94 lines
2.1 KiB
#include "satan.h"
|
|
|
|
#ifdef BACKLIGHT_ENABLE
|
|
#include "backlight.h"
|
|
#endif
|
|
|
|
__attribute__ ((weak))
|
|
void matrix_init_user(void) {
|
|
// leave these blank
|
|
};
|
|
|
|
__attribute__ ((weak))
|
|
void matrix_scan_user(void) {
|
|
// leave these blank
|
|
};
|
|
|
|
|
|
#ifdef BACKLIGHT_ENABLE
|
|
|
|
void backlight_init_ports()
|
|
{
|
|
|
|
// Setup PB6 as output and output low.
|
|
DDRB |= (1<<6);
|
|
PORTB &= ~(1<<6);
|
|
|
|
// Use full 16-bit resolution.
|
|
ICR1 = 0xFFFF;
|
|
|
|
// I could write a wall of text here to explain... but TL;DW
|
|
// Go read the ATmega32u4 datasheet.
|
|
// And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
|
|
|
|
// Pin PB6 = OCR1B (Timer 1, Channel C)
|
|
// Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0
|
|
// (i.e. start high, go low when counter matches.)
|
|
// WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
|
|
// Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
|
|
|
|
TCCR1A = _BV(COM1B1) | _BV(WGM11); // = 0b00001010;
|
|
TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
|
|
|
|
backlight_init();
|
|
}
|
|
|
|
void backlight_set(uint8_t level)
|
|
{
|
|
// Prevent backlight blink on lowest level
|
|
PORTB &= ~(_BV(PORTB6));
|
|
|
|
if ( level == 0 )
|
|
{
|
|
// Turn off PWM control on PB6, revert to output low.
|
|
TCCR1A &= ~(_BV(COM1B1));
|
|
OCR1B = 0x0;
|
|
}
|
|
else if ( level == BACKLIGHT_LEVELS )
|
|
{
|
|
// Turn on PWM control of PB6
|
|
TCCR1A |= _BV(COM1B1);
|
|
// Set the brightness
|
|
OCR1B = 0xFFFF;
|
|
}
|
|
else
|
|
{
|
|
// Turn on PWM control of PB6
|
|
TCCR1A |= _BV(COM1B1);
|
|
// Set the brightness
|
|
OCR1B = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
|
|
}
|
|
}
|
|
|
|
#endif
|
|
|
|
void matrix_init_kb(void) {
|
|
// put your keyboard start-up code here
|
|
// runs once when the firmware starts up
|
|
if (matrix_init_user) {
|
|
(*matrix_init_user)();
|
|
}
|
|
led_init_ports();
|
|
|
|
#ifdef BACKLIGHT_ENABLE
|
|
backlight_init_ports();
|
|
#endif
|
|
};
|
|
|
|
void matrix_scan_kb(void) {
|
|
// put your looping keyboard code here
|
|
// runs every cycle (a lot)
|
|
if (matrix_scan_user) {
|
|
(*matrix_scan_user)();
|
|
}
|
|
}; |