You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
148 lines
4.7 KiB
148 lines
4.7 KiB
/*
|
|
LUFA Library
|
|
Copyright (C) Dean Camera, 2010.
|
|
|
|
dean [at] fourwalledcubicle [dot] com
|
|
www.fourwalledcubicle.com
|
|
*/
|
|
|
|
/*
|
|
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
|
|
|
Permission to use, copy, modify, distribute, and sell this
|
|
software and its documentation for any purpose is hereby granted
|
|
without fee, provided that the above copyright notice appear in
|
|
all copies and that both that the copyright notice and this
|
|
permission notice and warranty disclaimer appear in supporting
|
|
documentation, and that the name of the author not be used in
|
|
advertising or publicity pertaining to distribution of the
|
|
software without specific, written prior permission.
|
|
|
|
The author disclaim all warranties with regard to this
|
|
software, including all implied warranties of merchantability
|
|
and fitness. In no event shall the author be liable for any
|
|
special, indirect or consequential damages or any damages
|
|
whatsoever resulting from loss of use, data or profits, whether
|
|
in an action of contract, negligence or other tortious action,
|
|
arising out of or in connection with the use or performance of
|
|
this software.
|
|
*/
|
|
|
|
/** \file
|
|
*
|
|
* Main source file for the TeensyHID bootloader. This file contains the complete bootloader logic.
|
|
*/
|
|
|
|
#include "TeensyHID.h"
|
|
|
|
/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
|
|
* via a soft reset. When cleared, the bootloader will abort, the USB interface will shut down and the application
|
|
* started via a forced watchdog reset.
|
|
*/
|
|
bool RunBootloader = true;
|
|
|
|
/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
|
|
* runs the bootloader processing routine until instructed to soft-exit.
|
|
*/
|
|
int main(void)
|
|
{
|
|
/* Setup hardware required for the bootloader */
|
|
SetupHardware();
|
|
|
|
while (RunBootloader)
|
|
USB_USBTask();
|
|
|
|
/* Disconnect from the host - USB interface will be reset later along with the AVR */
|
|
USB_Detach();
|
|
|
|
/* Enable the watchdog and force a timeout to reset the AVR */
|
|
wdt_enable(WDTO_250MS);
|
|
|
|
for (;;);
|
|
}
|
|
|
|
/** Configures all hardware required for the bootloader. */
|
|
void SetupHardware(void)
|
|
{
|
|
/* Disable watchdog if enabled by bootloader/fuses */
|
|
MCUSR &= ~(1 << WDRF);
|
|
wdt_disable();
|
|
|
|
/* Relocate the interrupt vector table to the bootloader section */
|
|
MCUCR = (1 << IVCE);
|
|
MCUCR = (1 << IVSEL);
|
|
|
|
/* Initialize USB subsystem */
|
|
USB_Init();
|
|
}
|
|
|
|
/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
|
|
* to relay data to and from the attached USB host.
|
|
*/
|
|
void EVENT_USB_Device_ConfigurationChanged(void)
|
|
{
|
|
/* Setup HID Report Endpoint */
|
|
Endpoint_ConfigureEndpoint(HID_EPNUM, EP_TYPE_INTERRUPT,
|
|
ENDPOINT_DIR_IN, HID_EPSIZE,
|
|
ENDPOINT_BANK_SINGLE);
|
|
}
|
|
|
|
/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
|
|
* control requests that are not handled internally by the USB library (including the HID commands, which are
|
|
* all issued via the control endpoint), so that they can be handled appropriately for the application.
|
|
*/
|
|
void EVENT_USB_Device_UnhandledControlRequest(void)
|
|
{
|
|
/* Handle HID Class specific requests */
|
|
switch (USB_ControlRequest.bRequest)
|
|
{
|
|
case REQ_SetReport:
|
|
Endpoint_ClearSETUP();
|
|
|
|
/* Wait until the command has been sent by the host */
|
|
while (!(Endpoint_IsOUTReceived()));
|
|
|
|
/* Read in the write destination address */
|
|
uint16_t PageAddress = Endpoint_Read_Word_LE();
|
|
|
|
/* Check if the command is a program page command, or a start application command */
|
|
if (PageAddress == TEENSY_STARTAPPLICATION)
|
|
{
|
|
RunBootloader = false;
|
|
}
|
|
else
|
|
{
|
|
/* Erase the given FLASH page, ready to be programmed */
|
|
boot_page_erase(PageAddress);
|
|
boot_spm_busy_wait();
|
|
|
|
/* Write each of the FLASH page's bytes in sequence */
|
|
for (uint8_t PageByte = 0; PageByte < SPM_PAGESIZE; PageByte += 2)
|
|
{
|
|
/* Check if endpoint is empty - if so clear it and wait until ready for next packet */
|
|
if (!(Endpoint_BytesInEndpoint()))
|
|
{
|
|
Endpoint_ClearOUT();
|
|
while (!(Endpoint_IsOUTReceived()));
|
|
}
|
|
|
|
/* Write the next data word to the FLASH page */
|
|
boot_page_fill(PageAddress + PageByte, Endpoint_Read_Word_LE());
|
|
}
|
|
|
|
/* Write the filled FLASH page to memory */
|
|
boot_page_write(PageAddress);
|
|
boot_spm_busy_wait();
|
|
|
|
/* Re-enable RWW section */
|
|
boot_rww_enable();
|
|
}
|
|
|
|
Endpoint_ClearOUT();
|
|
|
|
Endpoint_ClearStatusStage();
|
|
|
|
break;
|
|
}
|
|
}
|