You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
226 lines
11 KiB
226 lines
11 KiB
/** \file
|
|
*
|
|
* This file contains special DoxyGen information for the generation of the main page and other special
|
|
* documentation pages. It is not a project source file.
|
|
*/
|
|
|
|
/** \mainpage Mass Storage Class USB AVR Bootloader
|
|
*
|
|
* \section Sec_Compat Demo Compatibility:
|
|
*
|
|
* The following list indicates what microcontrollers are compatible with this demo.
|
|
*
|
|
* \li Series 7 USB AVRs (AT90USBxxx7)
|
|
* \li Series 6 USB AVRs (AT90USBxxx6)
|
|
* \li Series 4 USB AVRs (ATMEGAxxU4) - <i>See \ref SSec_Aux_Space</i>
|
|
* \li ATMEGA32U2 - <i>See \ref SSec_Aux_Space</i>
|
|
*
|
|
* \section Sec_Info USB Information:
|
|
*
|
|
* The following table gives a rundown of the USB utilization of this demo.
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <td><b>USB Mode:</b></td>
|
|
* <td>Device</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>USB Class:</b></td>
|
|
* <td>Mass Storage Device</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>USB Subclass:</b></td>
|
|
* <td>Bulk-Only Transport</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>Relevant Standards:</b></td>
|
|
* <td>USBIF Mass Storage Standard \n
|
|
* USB Bulk-Only Transport Standard \n
|
|
* SCSI Primary Commands Specification \n
|
|
* SCSI Block Commands Specification</td>
|
|
* </tr>
|
|
* <tr>
|
|
* <td><b>Supported USB Speeds:</b></td>
|
|
* <td>Full Speed Mode</td>
|
|
* </tr>
|
|
* </table>
|
|
*
|
|
* \section Sec_Description Project Description:
|
|
*
|
|
* This bootloader enumerates to the host as a Mass Storage device, capable of reading and writing a new binary
|
|
* firmware image file, to load firmware onto the AVR.
|
|
*
|
|
* Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
|
|
* into 6KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to
|
|
* edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
|
|
*
|
|
* When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
|
|
* bootloader from the normal user application.
|
|
*
|
|
* \warning <b>THIS BOOTLOADER IS NOT SECURE.</b> Malicious entities can recover written data, even if the device
|
|
* lockbits are set.
|
|
*
|
|
* \section Sec_Running Running the Bootloader
|
|
*
|
|
* This bootloader is designed to be started via the HWB mechanism of the USB AVRs; ground the HWB pin (see device
|
|
* datasheet) then momentarily ground /RESET to start the bootloader. This assumes the HWBE fuse is set and the BOOTRST
|
|
* fuse is cleared.
|
|
*
|
|
* For board specific exceptions to the above, see below.
|
|
*
|
|
* \subsection SSec_XPLAIN Atmel Xplain Board
|
|
* Ground the USB AVR JTAG's \c TCK pin to ground when powering on the board to start the bootloader. This assumes the
|
|
* \c HWBE fuse is cleared and the \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board.
|
|
*
|
|
* \subsection SSec_Leonardo Arduino Leonardo Board
|
|
* Ground \c IO13 when powering the board to start the bootloader. This assumes the \c HWBE fuse is cleared and the
|
|
* \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board.
|
|
*
|
|
* \section Sec_Installation Driver Installation
|
|
*
|
|
* This bootloader uses the Mass Storage drivers inbuilt into all modern operating systems, thus no additional
|
|
* drivers need to be supplied for correct operation.
|
|
*
|
|
* \section Sec_HostApp Host Controller Application
|
|
*
|
|
* This bootloader is compatible with all operating systems that support the FAT12 file system format. To reprogram the
|
|
* device, overwrite a file stored on the virtual FAT filesystem with a new binary (BIN format) image. Remember to safely
|
|
* remove your device from the host using the host OS's ejection APIs, to ensure all data is correctly flushed to the
|
|
* bootloader's virtual filesystem and not cached in the OS's file system driver.
|
|
*
|
|
* The current device firmware can be read from the device by reading a file from the virtual FAT filesystem.
|
|
*
|
|
* \warning This bootloader is currently <b>incompatible with the Apple MacOS X OS Finder GUI</b>, due to the
|
|
* large amount of meta files this OS attempts to write to the disk along with the new binaries. On
|
|
* this platform, firmwares must be copied to the disk via the Terminal application only to prevent
|
|
* firmware corruption.
|
|
*
|
|
* \section Sec_API User Application API
|
|
*
|
|
* Several user application functions for FLASH and other special memory area manipulations are exposed by the bootloader,
|
|
* allowing the user application to call into the bootloader at runtime to read and write FLASH data.
|
|
*
|
|
* By default, the bootloader API jump table is located 32 bytes from the end of the device's FLASH memory, and follows the
|
|
* following layout:
|
|
*
|
|
* \code
|
|
* #define BOOTLOADER_API_TABLE_SIZE 32
|
|
* #define BOOTLOADER_API_TABLE_START ((FLASHEND + 1UL) - BOOTLOADER_API_TABLE_SIZE)
|
|
* #define BOOTLOADER_API_CALL(Index) (void*)((BOOTLOADER_API_TABLE_START + (Index * 2)) / 2)
|
|
*
|
|
* void (*BootloaderAPI_ErasePage)(uint32_t Address) = BOOTLOADER_API_CALL(0);
|
|
* void (*BootloaderAPI_WritePage)(uint32_t Address) = BOOTLOADER_API_CALL(1);
|
|
* void (*BootloaderAPI_FillWord)(uint32_t Address, uint16_t Word) = BOOTLOADER_API_CALL(2);
|
|
* uint8_t (*BootloaderAPI_ReadSignature)(uint16_t Address) = BOOTLOADER_API_CALL(3);
|
|
* uint8_t (*BootloaderAPI_ReadFuse)(uint16_t Address) = BOOTLOADER_API_CALL(4);
|
|
* uint8_t (*BootloaderAPI_ReadLock)(void) = BOOTLOADER_API_CALL(5);
|
|
* void (*BootloaderAPI_WriteLock)(uint8_t LockBits) = BOOTLOADER_API_CALL(6);
|
|
*
|
|
* #define BOOTLOADER_MAGIC_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 2))
|
|
* #define BOOTLOADER_MAGIC_SIGNATURE 0xDCFB
|
|
*
|
|
* #define BOOTLOADER_CLASS_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 4))
|
|
* #define BOOTLOADER_MASS_STORAGE_SIGNATURE 0xDF30
|
|
*
|
|
* #define BOOTLOADER_ADDRESS_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 8))
|
|
* #define BOOTLOADER_ADDRESS_LENGTH 4
|
|
* \endcode
|
|
*
|
|
* From the application the API support of the bootloader can be detected by reading the FLASH memory bytes located at address
|
|
* \c BOOTLOADER_MAGIC_SIGNATURE_START and comparing them to the value \c BOOTLOADER_MAGIC_SIGNATURE. The class of bootloader
|
|
* can be determined by reading the FLASH memory bytes located at address \c BOOTLOADER_CLASS_SIGNATURE_START and comparing them
|
|
* to the value \c BOOTLOADER_MASS_STORAGE_SIGNATURE. The start address of the bootloader can be retrieved by reading the bytes
|
|
* of FLASH memory starting from address \c BOOTLOADER_ADDRESS_START.
|
|
*
|
|
* \subsection SSec_Aux_Space Auxiliary Bootloader Section
|
|
* To make the bootloader function on smaller devices (those with a physical bootloader section of smaller than 6KB) a second
|
|
* section of memory (called the <i>Auxiliary Bootloader Section</i>) is added before the start of the real bootloader section,
|
|
* and is filled with a portion of the bootloader code. This allows smaller devices to run the bootloader, at the cost of an
|
|
* additional portion of the device's FLASH (the bootloader section size in KB subtracted from the 6KB total size). A small
|
|
* trampoline is inserted at the start of the auxiliary section so that the bootloader will run normally in the case of a blank
|
|
* application section.
|
|
*
|
|
* On devices supporting a 8KB bootloader section size, the AUX section is not created in the final binary.
|
|
*
|
|
* \subsection SSec_API_MemLayout Device Memory Map
|
|
* The following illustration indicates the final memory map of the device when loaded with the bootloader.
|
|
*
|
|
* \verbatim
|
|
* +----------------------------+ 0x0000
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | User Application |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* | |
|
|
* +----------------------------+ FLASHEND - BOOT_SECTION_SIZE - BOOT_AUX_SECTION_SIZE
|
|
* | Booloader Start Trampoline |
|
|
* | (Not User App. Accessible) |
|
|
* +----------------------------+ FLASHEND - BOOT_SECTION_SIZE - BOOT_AUX_SECTION_SIZE + 4
|
|
* | |
|
|
* | Auxiliary Bootloader |
|
|
* | Space for Smaller Devices |
|
|
* | (Not User App. Accessible) |
|
|
* | |
|
|
* +----------------------------+ FLASHEND - BOOT_SECTION_SIZE
|
|
* | |
|
|
* | Bootloader Application |
|
|
* | (Not User App. Accessible) |
|
|
* | |
|
|
* +----------------------------+ FLASHEND - 96
|
|
* | API Table Trampolines |
|
|
* | (Not User App. Accessible) |
|
|
* +----------------------------+ FLASHEND - 32
|
|
* | Bootloader API Table |
|
|
* | (User App. Accessible) |
|
|
* +----------------------------+ FLASHEND - 8
|
|
* | Bootloader ID Constants |
|
|
* | (User App. Accessible) |
|
|
* +----------------------------+ FLASHEND
|
|
* \endverbatim
|
|
*
|
|
* \section Sec_KnownIssues Known Issues:
|
|
*
|
|
* \par In some cases, the application is not fully loaded into the device.
|
|
* Write-caching on some operating systems may interfere with the normal
|
|
* operation of the bootloader. Write caching should be disabled when using the
|
|
* Mass Storage bootloader, or the file system synced via an appropriate command
|
|
* (such as the OS's normal disk ejection command) before disconnecting the device.
|
|
*
|
|
* \par After loading an application, it is not run automatically on startup.
|
|
* Some USB AVR boards ship with the BOOTRST fuse set, causing the bootloader
|
|
* to run automatically when the device is reset. In most cases, the BOOTRST
|
|
* fuse should be disabled and the HWBE fuse used instead to run the bootloader
|
|
* when needed.
|
|
*
|
|
* \section Sec_Options Project Options
|
|
*
|
|
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
|
|
*
|
|
* <table>
|
|
* <tr>
|
|
* <th><b>Define Name:</b></th>
|
|
* <th><b>Location:</b></th>
|
|
* <th><b>Description:</b></th>
|
|
* </tr>
|
|
* <tr>
|
|
* <td>NO_APP_START_ON_EJECT</td>
|
|
* <td>AppConfig.h</td>
|
|
* <td>Define to disable automatic start of the loaded application when the virtual
|
|
* Mass Storage disk is ejected on the host.</td>
|
|
* </tr>
|
|
* </table>
|
|
*/
|
|
|