You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
341 lines
12 KiB
341 lines
12 KiB
/*
|
|
LUFA Library
|
|
Copyright (C) Dean Camera, 2009.
|
|
|
|
dean [at] fourwalledcubicle [dot] com
|
|
www.fourwalledcubicle.com
|
|
*/
|
|
|
|
/*
|
|
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
|
|
|
Permission to use, copy, modify, and distribute this software
|
|
and its documentation for any purpose and without fee is hereby
|
|
granted, provided that the above copyright notice appear in all
|
|
copies and that both that the copyright notice and this
|
|
permission notice and warranty disclaimer appear in supporting
|
|
documentation, and that the name of the author not be used in
|
|
advertising or publicity pertaining to distribution of the
|
|
software without specific, written prior permission.
|
|
|
|
The author disclaim all warranties with regard to this
|
|
software, including all implied warranties of merchantability
|
|
and fitness. In no event shall the author be liable for any
|
|
special, indirect or consequential damages or any damages
|
|
whatsoever resulting from loss of use, data or profits, whether
|
|
in an action of contract, negligence or other tortious action,
|
|
arising out of or in connection with the use or performance of
|
|
this software.
|
|
*/
|
|
|
|
#include "USBtoSerial.h"
|
|
|
|
/** Contains the current baud rate and other settings of the virtual serial port.
|
|
*
|
|
* These values are set by the host via a class-specific request, and the physical USART should be reconfigured to match the
|
|
* new settings each time they are changed by the host.
|
|
*/
|
|
CDC_Line_Coding_t LineEncoding = { .BaudRateBPS = 0,
|
|
.CharFormat = OneStopBit,
|
|
.ParityType = Parity_None,
|
|
.DataBits = 8 };
|
|
|
|
/** Ring (circular) buffer to hold the RX data - data from the host to the attached device on the serial port. */
|
|
RingBuff_t Rx_Buffer;
|
|
|
|
/** Ring (circular) buffer to hold the TX data - data from the attached device on the serial port to the host. */
|
|
RingBuff_t Tx_Buffer;
|
|
|
|
/** Flag to indicate if the USART is currently transmitting data from the Rx_Buffer circular buffer. */
|
|
volatile bool Transmitting = false;
|
|
|
|
|
|
/** Main program entry point. This routine configures the hardware required by the application, then
|
|
* enters a loop to run the application tasks in sequence.
|
|
*/
|
|
int main(void)
|
|
{
|
|
SetupHardware();
|
|
|
|
/* Ring buffer Initialization */
|
|
Buffer_Initialize(&Rx_Buffer);
|
|
Buffer_Initialize(&Tx_Buffer);
|
|
|
|
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
|
|
|
for (;;)
|
|
{
|
|
CDC_Task();
|
|
USB_USBTask();
|
|
}
|
|
}
|
|
|
|
/** Configures the board hardware and chip peripherals for the demo's functionality. */
|
|
void SetupHardware(void)
|
|
{
|
|
/* Disable watchdog if enabled by bootloader/fuses */
|
|
MCUSR &= ~(1 << WDRF);
|
|
wdt_disable();
|
|
|
|
/* Disable clock division */
|
|
clock_prescale_set(clock_div_1);
|
|
|
|
/* Hardware Initialization */
|
|
Serial_Init(9600, false);
|
|
LEDs_Init();
|
|
USB_Init();
|
|
}
|
|
|
|
/** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
|
|
* starts the library USB task to begin the enumeration and USB management process.
|
|
*/
|
|
void EVENT_USB_Device_Connect(void)
|
|
{
|
|
/* Indicate USB enumerating */
|
|
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
|
|
}
|
|
|
|
/** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
|
|
* the status LEDs and stops the USB management and CDC management tasks.
|
|
*/
|
|
void EVENT_USB_Device_Disconnect(void)
|
|
{
|
|
/* Reset Tx and Rx buffers, device disconnected */
|
|
Buffer_Initialize(&Rx_Buffer);
|
|
Buffer_Initialize(&Tx_Buffer);
|
|
|
|
/* Indicate USB not ready */
|
|
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
|
}
|
|
|
|
/** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration
|
|
* of the USB device after enumeration - the device endpoints are configured and the CDC management task started.
|
|
*/
|
|
void EVENT_USB_Device_ConfigurationChanged(void)
|
|
{
|
|
/* Indicate USB connected and ready */
|
|
LEDs_SetAllLEDs(LEDMASK_USB_READY);
|
|
|
|
/* Setup CDC Notification, Rx and Tx Endpoints */
|
|
if (!(Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,
|
|
ENDPOINT_DIR_IN, CDC_NOTIFICATION_EPSIZE,
|
|
ENDPOINT_BANK_SINGLE)))
|
|
{
|
|
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
|
}
|
|
|
|
if (!(Endpoint_ConfigureEndpoint(CDC_TX_EPNUM, EP_TYPE_BULK,
|
|
ENDPOINT_DIR_IN, CDC_TXRX_EPSIZE,
|
|
ENDPOINT_BANK_SINGLE)))
|
|
{
|
|
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
|
}
|
|
|
|
if (!(Endpoint_ConfigureEndpoint(CDC_RX_EPNUM, EP_TYPE_BULK,
|
|
ENDPOINT_DIR_OUT, CDC_TXRX_EPSIZE,
|
|
ENDPOINT_BANK_SINGLE)))
|
|
{
|
|
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
|
}
|
|
|
|
/* Reset line encoding baud rate so that the host knows to send new values */
|
|
LineEncoding.BaudRateBPS = 0;
|
|
}
|
|
|
|
/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
|
|
* control requests that are not handled internally by the USB library (including the CDC control commands,
|
|
* which are all issued via the control endpoint), so that they can be handled appropriately for the application.
|
|
*/
|
|
void EVENT_USB_Device_UnhandledControlRequest(void)
|
|
{
|
|
/* Process CDC specific control requests */
|
|
switch (USB_ControlRequest.bRequest)
|
|
{
|
|
case REQ_GetLineEncoding:
|
|
if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
|
|
{
|
|
/* Acknowledge the SETUP packet, ready for data transfer */
|
|
Endpoint_ClearSETUP();
|
|
|
|
/* Write the line coding data to the control endpoint */
|
|
Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(LineEncoding));
|
|
|
|
/* Finalize the stream transfer to send the last packet or clear the host abort */
|
|
Endpoint_ClearOUT();
|
|
}
|
|
|
|
break;
|
|
case REQ_SetLineEncoding:
|
|
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
|
|
{
|
|
/* Acknowledge the SETUP packet, ready for data transfer */
|
|
Endpoint_ClearSETUP();
|
|
|
|
/* Read the line coding data in from the host into the global struct */
|
|
Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(LineEncoding));
|
|
|
|
/* Finalize the stream transfer to clear the last packet from the host */
|
|
Endpoint_ClearIN();
|
|
|
|
/* Reconfigure the USART with the new settings */
|
|
ReconfigureUSART();
|
|
}
|
|
|
|
break;
|
|
case REQ_SetControlLineState:
|
|
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
|
|
{
|
|
/* Acknowledge the SETUP packet, ready for data transfer */
|
|
Endpoint_ClearSETUP();
|
|
|
|
/* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake
|
|
lines. The mask is read in from the wValue parameter in USB_ControlRequest, and can be masked against the
|
|
CONTROL_LINE_OUT_* masks to determine the RTS and DTR line states using the following code:
|
|
*/
|
|
|
|
Endpoint_ClearStatusStage();
|
|
}
|
|
|
|
break;
|
|
}
|
|
}
|
|
|
|
/** Task to manage CDC data transmission and reception to and from the host, from and to the physical USART. */
|
|
void CDC_Task(void)
|
|
{
|
|
/* Device must be connected and configured for the task to run */
|
|
if (USB_DeviceState != DEVICE_STATE_Configured)
|
|
return;
|
|
|
|
#if 0
|
|
/* NOTE: Here you can use the notification endpoint to send back line state changes to the host, for the special RS-232
|
|
handshake signal lines (and some error states), via the CONTROL_LINE_IN_* masks and the following code:
|
|
*/
|
|
|
|
USB_Notification_Header_t Notification = (USB_Notification_Header_t)
|
|
{
|
|
.NotificationType = (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE),
|
|
.Notification = NOTIF_SerialState,
|
|
.wValue = 0,
|
|
.wIndex = 0,
|
|
.wLength = sizeof(uint16_t),
|
|
};
|
|
|
|
uint16_t LineStateMask;
|
|
|
|
// Set LineStateMask here to a mask of CONTROL_LINE_IN_* masks to set the input handshake line states to send to the host
|
|
|
|
Endpoint_SelectEndpoint(CDC_NOTIFICATION_EPNUM);
|
|
Endpoint_Write_Stream_LE(&Notification, sizeof(Notification));
|
|
Endpoint_Write_Stream_LE(&LineStateMask, sizeof(LineStateMask));
|
|
Endpoint_ClearIN();
|
|
#endif
|
|
|
|
/* Select the Serial Rx Endpoint */
|
|
Endpoint_SelectEndpoint(CDC_RX_EPNUM);
|
|
|
|
/* Check to see if a packet has been received from the host */
|
|
if (Endpoint_IsOUTReceived())
|
|
{
|
|
/* Read the bytes in from the endpoint into the buffer while space is available */
|
|
while (Endpoint_BytesInEndpoint() && (Rx_Buffer.Elements != BUFF_STATICSIZE))
|
|
{
|
|
/* Store each character from the endpoint */
|
|
Buffer_StoreElement(&Rx_Buffer, Endpoint_Read_Byte());
|
|
}
|
|
|
|
/* Check to see if all bytes in the current packet have been read */
|
|
if (!(Endpoint_BytesInEndpoint()))
|
|
{
|
|
/* Clear the endpoint buffer */
|
|
Endpoint_ClearOUT();
|
|
}
|
|
}
|
|
|
|
/* Check if Rx buffer contains data - if so, send it */
|
|
if (Rx_Buffer.Elements)
|
|
Serial_TxByte(Buffer_GetElement(&Rx_Buffer));
|
|
|
|
/* Select the Serial Tx Endpoint */
|
|
Endpoint_SelectEndpoint(CDC_TX_EPNUM);
|
|
|
|
/* Check if the Tx buffer contains anything to be sent to the host */
|
|
if ((Tx_Buffer.Elements) && LineEncoding.BaudRateBPS)
|
|
{
|
|
/* Wait until Serial Tx Endpoint Ready for Read/Write */
|
|
Endpoint_WaitUntilReady();
|
|
|
|
/* Write the bytes from the buffer to the endpoint while space is available */
|
|
while (Tx_Buffer.Elements && Endpoint_IsReadWriteAllowed())
|
|
{
|
|
/* Write each byte retreived from the buffer to the endpoint */
|
|
Endpoint_Write_Byte(Buffer_GetElement(&Tx_Buffer));
|
|
}
|
|
|
|
/* Remember if the packet to send completely fills the endpoint */
|
|
bool IsFull = (Endpoint_BytesInEndpoint() == CDC_TXRX_EPSIZE);
|
|
|
|
/* Send the data */
|
|
Endpoint_ClearIN();
|
|
|
|
/* If no more data to send and the last packet filled the endpoint, send an empty packet to release
|
|
* the buffer on the receiver (otherwise all data will be cached until a non-full packet is received) */
|
|
if (IsFull && !(Tx_Buffer.Elements))
|
|
{
|
|
/* Wait until Serial Tx Endpoint Ready for Read/Write */
|
|
Endpoint_WaitUntilReady();
|
|
|
|
/* Send an empty packet to terminate the transfer */
|
|
Endpoint_ClearIN();
|
|
}
|
|
}
|
|
}
|
|
|
|
/** ISR to handle the USART receive complete interrupt, fired each time the USART has received a character. This stores the received
|
|
* character into the Tx_Buffer circular buffer for later transmission to the host.
|
|
*/
|
|
ISR(USART1_RX_vect, ISR_BLOCK)
|
|
{
|
|
uint8_t ReceivedByte = UDR1;
|
|
|
|
/* Only store received characters if the USB interface is connected */
|
|
if ((USB_DeviceState == DEVICE_STATE_Configured) && LineEncoding.BaudRateBPS)
|
|
Buffer_StoreElement(&Tx_Buffer, ReceivedByte);
|
|
}
|
|
|
|
/** Reconfigures the USART to match the current serial port settings issued by the host as closely as possible. */
|
|
void ReconfigureUSART(void)
|
|
{
|
|
uint8_t ConfigMask = 0;
|
|
|
|
/* Determine parity - non odd/even parity mode defaults to no parity */
|
|
if (LineEncoding.ParityType == Parity_Odd)
|
|
ConfigMask = ((1 << UPM11) | (1 << UPM10));
|
|
else if (LineEncoding.ParityType == Parity_Even)
|
|
ConfigMask = (1 << UPM11);
|
|
|
|
/* Determine stop bits - 1.5 stop bits is set as 1 stop bit due to hardware limitations */
|
|
if (LineEncoding.CharFormat == TwoStopBits)
|
|
ConfigMask |= (1 << USBS1);
|
|
|
|
/* Determine data size - 5, 6, 7, or 8 bits are supported */
|
|
if (LineEncoding.DataBits == 6)
|
|
ConfigMask |= (1 << UCSZ10);
|
|
else if (LineEncoding.DataBits == 7)
|
|
ConfigMask |= (1 << UCSZ11);
|
|
else if (LineEncoding.DataBits == 8)
|
|
ConfigMask |= ((1 << UCSZ11) | (1 << UCSZ10));
|
|
|
|
/* Enable double speed, gives better error percentages at 8MHz */
|
|
UCSR1A = (1 << U2X1);
|
|
|
|
/* Enable transmit and receive modules and interrupts */
|
|
UCSR1B = ((1 << RXCIE1) | (1 << TXEN1) | (1 << RXEN1));
|
|
|
|
/* Set the USART mode to the mask generated by the Line Coding options */
|
|
UCSR1C = ConfigMask;
|
|
|
|
/* Set the USART baud rate register to the desired baud rate value */
|
|
UBRR1 = SERIAL_2X_UBBRVAL((uint16_t)LineEncoding.BaudRateBPS);
|
|
}
|