You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
qmk_firmware/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h

155 lines
5.1 KiB

/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for XPROGTarget.c.
*/
#ifndef _XPROG_TARGET_
#define _XPROG_TARGET_
/* Includes: */
#include <avr/io.h>
#include <avr/interrupt.h>
#include <stdbool.h>
#include <LUFA/Common/Common.h>
#include "../V2Protocol.h"
#include "XPROGProtocol.h"
/* Preprocessor Checks: */
#if ((BOARD == BOARD_XPLAIN) || (BOARD == BOARD_XPLAIN_REV1))
#undef ENABLE_ISP_PROTOCOL
#if !defined(ENABLE_XPROG_PROTOCOL)
#define ENABLE_XPROG_PROTOCOL
#endif
#endif
/* Defines: */
#if ((BOARD == BOARD_XPLAIN) || (BOARD == BOARD_XPLAIN_REV1))
#define XPROG_VIA_HARDWARE_USART
#else
#define BITBANG_PDIDATA_PORT PORTB
#define BITBANG_PDIDATA_DDR DDRB
#define BITBANG_PDIDATA_PIN PINB
#define BITBANG_PDIDATA_MASK (1 << 3)
#define BITBANG_PDICLOCK_PORT AUX_LINE_PORT
#define BITBANG_PDICLOCK_DDR AUX_LINE_DDR
#define BITBANG_PDICLOCK_PIN AUX_LINE_PIN
#define BITBANG_PDICLOCK_MASK AUX_LINE_MASK
#define BITBANG_TPIDATA_PORT PORTB
#define BITBANG_TPIDATA_DDR DDRB
#define BITBANG_TPIDATA_PIN PINB
#define BITBANG_TPIDATA_MASK (1 << 3)
#define BITBANG_TPICLOCK_PORT PORTB
#define BITBANG_TPICLOCK_DDR DDRB
#define BITBANG_TPICLOCK_PIN PINB
#define BITBANG_TPICLOCK_MASK (1 << 1)
#endif
/** Serial carrier TPI/PDI speed when hardware TPI/PDI mode is used */
#define XPROG_HARDWARE_SPEED 500000
/** Number of cycles between each clock when software USART mode is used */
#define BITS_BETWEEN_USART_CLOCKS 100
/** Total number of bits in a single USART frame */
#define BITS_IN_USART_FRAME 12
#define PDI_CMD_LDS 0x00
#define PDI_CMD_LD 0x20
#define PDI_CMD_STS 0x40
#define PDI_CMD_ST 0x60
#define PDI_CMD_LDCS 0x80
#define PDI_CMD_REPEAT 0xA0
#define PDI_CMD_STCS 0xC0
#define PDI_CMD_KEY 0xE0
#define PDI_STATUS_REG 0
#define PDI_RESET_REG 1
#define PDI_CTRL_REG 2
#define PDI_STATUS_NVM (1 << 1)
#define PDI_RESET_KEY 0x59
#define PDI_NVMENABLE_KEY (uint8_t[]){0x12, 0x89, 0xAB, 0x45, 0xCD, 0xD8, 0x88, 0xFF}
#define PDI_DATSIZE_1BYTE 0
#define PDI_DATSIZE_2BYTES 1
#define PDI_DATSIZE_3BYTES 2
#define PDI_DATSIZE_4BYTES 3
#define PDI_POINTER_INDIRECT 0
#define PDI_POINTER_INDIRECT_PI 1
#define PDI_POINTER_DIRECT 2
#define TPI_CMD_SLD 0x20
#define TPI_CMD_SST 0x60
#define TPI_CMD_SSTPR 0x68
#define TPI_CMD_SIN 0x10
#define TPI_CMD_SOUT 0x90
#define TPI_CMD_SLDCS 0x80
#define TPI_CMD_SSTCS 0xC0
#define TPI_CMD_SKEY 0xE0
#define TPI_STATUS_REG 0x00
#define TPI_CTRL_REG 0x02
#define TPI_ID_REG 0x0F
#define TPI_STATUS_NVM (1 << 1)
#define TPI_NVMENABLE_KEY (uint8_t[]){0x12, 0x89, 0xAB, 0x45, 0xCD, 0xD8, 0x88, 0xFF}
#define TPI_POINTER_INDIRECT 0
#define TPI_POINTER_INDIRECT_PI 4
/* Function Prototypes: */
void XPROGTarget_EnableTargetPDI(void);
void XPROGTarget_EnableTargetTPI(void);
void XPROGTarget_DisableTargetPDI(void);
void XPROGTarget_DisableTargetTPI(void);
void XPROGTarget_SendByte(const uint8_t Byte);
uint8_t XPROGTarget_ReceiveByte(void);
void XPROGTarget_SendBreak(void);
bool XPROGTarget_WaitWhileNVMBusBusy(void);
#if defined(INCLUDE_FROM_XPROGTARGET_C)
static void XPROGTarget_SetTxMode(void);
static void XPROGTarget_SetRxMode(void);
#endif
#endif