19ebc2bfe1
PCB: trac cosmetix around SDRAM
7 years ago
85c17afe89
PCB: new inductors footprint and trac cosmetix around them
7 years ago
ea933eefe7
PCB: remove 3D models from resistors which should not be soldered
7 years ago
8f751545b2
PCB: reloaded with new U11 i2c schematic symbol
7 years ago
f3701f7f3e
PCB: J2 silkscreen labels
7 years ago
40e7ad7400
PCB: v1.8.3
7 years ago
a6d1e66dea
PCB: unclutter silkscreen and trac cosmetix
7 years ago
cd2c041273
PCB: resistor footprints changed, unclutter silkscreen again
7 years ago
7592c8a448
PCB: unclutter silkscreen (mostly done)
7 years ago
81e30ee0f2
PCB: unclutter silkscreen (partially done)
7 years ago
e51217fa05
PCB: audio DAC resistors moved closer to each other
7 years ago
a3cbf3e2cc
PCB: re-run DRC
7 years ago
4dae36d912
PCB: silkscreen clean up battery markings
7 years ago
97010a4d39
PCB: add PIN1 dot to usbserial chip U6 FT231X
7 years ago
0e0680c05f
PCB: change voltage and wifi pin headers to vertical and
...
their respective 3D models keep horizontal
7 years ago
4c907b1887
PCB: update footprints for fixed voltage selector jumpers
7 years ago
369fc1976e
PCB: oled LED 3D model purged from bak file
7 years ago
427ed638f0
PCB: cleanup LED silkscreen reference
7 years ago
712a05e534
PCB: Using 3D model of GPDI connector
7 years ago
294edf5956
PCB v1.8.2
7 years ago
01cc27ac43
PCB: updating resistor footprints
7 years ago
d3b1eb567c
PCB: antenna as test point
7 years ago
31c7fb7ded
PCB: diode symbols updated
7 years ago
0c8b571e22
PCB: changed L1,2,3 footprints to fit DFE252012P-2R2M=P2
7 years ago
0c1053921f
PCB: 3D models for pin headers
7 years ago
28bf25f446
PCB: 3D models for L1,2,3
7 years ago
df56b52931
PCB: DRC re-run
7 years ago
ec7088698c
PCB: generic DC-DC converter replaced
7 years ago
16a0caaeca
PCB: New SMD resistor footprints for LEDs on top side
7 years ago
2b65c61596
PCB: Align text reference BTN2 to same Y as BTN1
7 years ago
b519aefd09
PCB v1.8.1: change GPDI1 to FCI
7 years ago
7c9aca2381
PCB: moving resistors and vias under HDMI to make space for new FCI connector
7 years ago
8374131289
PCB: RP4,5 factory default jumper placeholders for 2.5/3.3V voltage setting
7 years ago
7f0df8c201
PCB: diodes new footprints, 3D models for diodes, pushbuttons, ICs, USB connectors
7 years ago
51d9149ec7
PCB: capacitors rerouted with clearance
7 years ago
4dbc97961f
PCB: re-run DRC
7 years ago
49bdc24d97
PCB: C54 22uF for 3V RTC battery and battery pad clearance
7 years ago
197b1166a2
PCB: removing obsolete traces from US2 connector
7 years ago
10b285212c
PCB: kicad 5 load and save
7 years ago
67d91dda07
PCB: export paste layer
7 years ago
adb7e6eef1
PCB: v1.8 capacitor for 2.5/3.3V
7 years ago
4cd2f833d7
PCB: v1.7.16 capacitor near SDRAM and trac cosmetix
7 years ago
5775212c8c
PCB: trac cosmetix++
...
Numerous small route optimizations,
Reducing inductive loops at copper fill areas on
board power distribution.
preparation to send for production of v1.8
7 years ago
3606470a5c
PCB: v1.7.15 J1,2 22nF capacitors
7 years ago
066d71f2fb
PCB: 2V5_3V3 on J1
7 years ago
68eed4b791
PCB: silkscreen writing 2.5V/3.3V under the jumper
7 years ago
1f6e8b240d
PCB: Voltage selection header moved deeper inside PCB
7 years ago
5216447da2
PCB: remove micro hdmi connector from library paths and change
...
3D footprint of 2.5/3.3V jumper to angled 2.54 mm header.
As shown, angled connector will occupy space required for
plugging HDMI connector.
The header should be placed deeper inside if possible.
7 years ago
4ef3866cea
PCB: join power supply copper fill areas under BGA and track clenaup
7 years ago
ff4f1ee73e
PCB: C47 for 2.5/3.3V
7 years ago
davor