davor
|
853497d403
|
schematics: replace 45F chip with 85F
|
7 years ago |
|
davor
|
3daf764426
|
schematics: new SMD resistor footprints for LEDs on top side
|
7 years ago |
|
davor
|
5d79943b9d
|
schematics: GPDI1 connector part number set to FCI 10029449-111RLF
|
7 years ago |
|
davor
|
1e7fd6f719
|
schematics: add molex part number for HDMI connector alternative
|
7 years ago |
|
davor
|
1f1ed2a72d
|
schematics: HDMI connector part number changed to match PCB layout
|
7 years ago |
|
davor
|
17ee1e3a07
|
schematics: diodes new footprints
|
7 years ago |
|
davor
|
b006a34b71
|
schematics: C54 22uF for 3V RTC battery
|
7 years ago |
|
davor
|
7b88b3baf1
|
schematics: v1.8 adding capacitor for 2.5/3.3V
|
7 years ago |
|
davor
|
1911c0afe2
|
schematics: add capacitor near SDRAM
|
7 years ago |
|
davor
|
ec8c012ebb
|
schematics: jumper for selectable 2.5V/3.3V J1 voltage
|
7 years ago |
|
davor
|
54dcca20fa
|
schematics: usb pull pins moved from gpio to gpdi bank
gpio is planned to become be voltage changeable 2.5/3.3V
while pulls should go to 3.3V
|
7 years ago |
|
davor
|
ea96ac0d18
|
schematics: use non-handsoldering footprints for all 22nF and 100nF capacitors
|
7 years ago |
|
davor
|
4ae602347e
|
schematics: power decoupling capactor near OLED
|
7 years ago |
|
davor
|
2ed35bea1a
|
schematics: AC coupling all GPDI differential lines
|
7 years ago |
|
davor
|
4a9b8c372b
|
schematics: HEAC capacitors to protect return of 5V from monitor to FPGA
|
7 years ago |
|
davor
|
8ff6e0e20e
|
schematics update, setting L1,L2,L3 all the same PN
|
7 years ago |
|
davor
|
42e3255b7a
|
schematics: US2 diodes pull up/down 1.5k/15k
|
7 years ago |
|
davor
|
b535b7ccee
|
schematics: references for buttons on previous PCB v1.7
|
7 years ago |
|
Emard
|
16fedcac96
|
schematics: additional 2 lines for US2 (GP,GN 22,25 moved)
|
7 years ago |
|
davor
|
2f3cc59274
|
schematics: adding mouser P/N
|
7 years ago |
|
davor
|
b205d52f4f
|
schematics: sprinkling 22nF decoupling capacitors under FPGA
|
7 years ago |
|
davor
|
a04b74cc61
|
schematics, footprints: micro usb cleanup
|
7 years ago |
|
davor
|
c1053dd7bd
|
schematics: cleanup of MFG_PN to simplify BOM
|
7 years ago |
|
davor
|
6b50f65544
|
footprints: FPGA renaming Quad SPI lines D2,D3
schematics: reference FPGA footprint directly (not from rescue file)
|
7 years ago |
|
davor
|
e81d05b68d
|
schematics: renaming pins J..+- to GP,GN..
|
7 years ago |
|
davor
|
0990aa8ac2
|
schematics: fix shutdown and i2c pullup to 5V D11=LED R4,R25,R26=4.7k
|
7 years ago |
|
davor
|
9ab20cb840
|
specific comments about RC shutdown constant on "power" sheet
|
7 years ago |
|
davor
|
766f96a80a
|
schematics: comments about i2c sharing
|
7 years ago |
|
davor
|
b41c200d79
|
schematics: cosmetics, hidign some button datasheet URL for schematics
|
7 years ago |
|
Emard
|
ea88fb4ceb
|
schematics: changed I2C and SPI FLASH part numbers to provide
150-mil SOIC-8 packages to fit one board.
FLASH increased 16->32Mb
|
7 years ago |
|
Emard
|
7aa1854030
|
schematics: use SOA008 footprint for the SPI flash chip
|
7 years ago |
|
Emard
|
3915779e0c
|
schematics: part numbers and URLs of datasheets and manufacturers
of most chips and connectors. Small parts not done yet.
|
7 years ago |
|
Emard
|
52814d6ae0
|
WIFI LED (blue) on schematics
|
7 years ago |
|
Emard
|
4a35c95132
|
GPDI CEC add protection resistor R61 470 ohm
|
7 years ago |
|
Emard
|
a5a51a8f28
|
connected missing SD card pins to esp-32
|
7 years ago |
|
Emard
|
cca17d282d
|
open-close to check that everything loads fine
|
7 years ago |
|
Emard
|
35b3a8b3dd
|
changing to 45F which is production device now
schem symbol 45F fixed typo T8->T7 (GND) and SERDES
|
7 years ago |
|
davor
|
0d71e508ae
|
analog: audio ring2 resistor DAC network connected to FPGA
copper infill is getting thin, so minimal-thickness traces
are used 0.127 mm
|
7 years ago |
|
davor
|
f843d3169a
|
gpdi sheet, i2c voltage shifter, VREF filtering with C18 100nF->470nF
|
7 years ago |
|
Emard
|
ba4c8e8d22
|
PCB v1.6 SDRAM fully reworked
|
7 years ago |
|
Emard
|
eca6978391
|
HDMI fixed wrong wiring PCB v1.5
and improving copper fill areas
|
7 years ago |
|
davor
|
bc41b3052d
|
move WIFI disable jumper closer to BTN1
|
7 years ago |
|
davor
|
1ea88bda53
|
Adding pins to schematic symbols for all chips in unit "H" (SERDES)
Non-serdes chips need GND connection on unit "H".
"power" sheet now connects GND's at unit "H".
|
7 years ago |
|
davor
|
bc4b88ee58
|
Micro SD: using SCHD3A0100
|
7 years ago |
|
davor
|
f3d84dbfdc
|
LED D19 was oriented wrong, now correct
|
7 years ago |
|
Emard
|
bab7ee607e
|
placeholder for 1.5k pullup for usb 1.0
|
7 years ago |
|
Emard
|
9cc436ce8c
|
Additional VCC 2.2uF blocking capacitors near the switching
power supply to form PI-filter with another 2.2uF near BGA
|
7 years ago |
|
Emard
|
bcf94bafab
|
buttons footprints correct now
|
7 years ago |
|
davor
|
236f63488a
|
DIP SWITCH routed
|
8 years ago |
|
davor
|
2153a220a0
|
schematic symbol for ADC MAX11123
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
|
8 years ago |
