6228263ac6
schematics: additional diode R23 to make shutdown more reliable
...
reduce hold resistor, use schottky for nSLEEP
7 years ago
b41c200d79
schematics: cosmetics, hidign some button datasheet URL for schematics
7 years ago
6cc027aed0
schematics: update inductor PN, swap L2 <-> L3
7 years ago
3915779e0c
schematics: part numbers and URLs of datasheets and manufacturers
...
of most chips and connectors. Small parts not done yet.
7 years ago
3336b63a5b
small schematics notes about WiFi
7 years ago
52814d6ae0
WIFI LED (blue) on schematics
7 years ago
4a35c95132
GPDI CEC add protection resistor R61 470 ohm
7 years ago
a5a51a8f28
connected missing SD card pins to esp-32
7 years ago
cca17d282d
open-close to check that everything loads fine
7 years ago
35b3a8b3dd
changing to 45F which is production device now
...
schem symbol 45F fixed typo T8->T7 (GND) and SERDES
7 years ago
6d74bb29fc
PCB v1.7 fix wrong audio jack connection
7 years ago
1ffed1dea1
comment at "usb" sheet about reasons for the JTAG pinout
...
different than ULX2s
7 years ago
ba4c8e8d22
PCB v1.6 SDRAM fully reworked
7 years ago
1ea88bda53
Adding pins to schematic symbols for all chips in unit "H" (SERDES)
...
Non-serdes chips need GND connection on unit "H".
"power" sheet now connects GND's at unit "H".
7 years ago
e4fc99887e
moving GND and VCC on schematics symbols to
...
common locations for planned PCB which
supports upgrade path for example
12F->25F->45F->85F and if possible ECP5U->ECP5UM
7 years ago
07de158d38
R56 for FT231X rev A,B,C workaround from TN140_FT231X Errata
7 years ago
1cdad1e4d0
all diodes SOD-323 and SOD-323F packages changed to handsoldering
...
(bigger pads, more reworkable)
silkscreen moving references GPDI1 and SW1 for readability
7 years ago
bc4b88ee58
Micro SD: using SCHD3A0100
7 years ago
f3d84dbfdc
LED D19 was oriented wrong, now correct
7 years ago
f8b5dc97eb
update SD card power supply and gerbers
7 years ago
bab7ee607e
placeholder for 1.5k pullup for usb 1.0
7 years ago
9cc436ce8c
Additional VCC 2.2uF blocking capacitors near the switching
...
power supply to form PI-filter with another 2.2uF near BGA
7 years ago
91ac1cc478
D8,D9,D51,D52: SMA package 2A low drop low profile
7 years ago
68a23c127c
set package SOD323 to all small diodes
7 years ago
eaf4c2402a
Fab layer, moving values to avoid overlap writings
...
GPDI footprint edited to remove some unneeded lines
Gerbers update
7 years ago
f120d212d9
433 MHz onboard antenna (need to uncover copper infill layers)
7 years ago
9f6eae914c
connecting almost all free pins from ESP32 to FPGA
...
(only 4 left unconnected)
7 years ago
600c4478fd
esp32: avoid connection to NC pin for JTAG_TDO
7 years ago
0229a768ad
FPGA direct-to-pin Hackish USB transciver 27 ohm + 3.6 V zener
7 years ago
fdf38ad9a1
DIP switch moved to the right, near RAM.
...
Maybe should be moved more to the right not to overlap with OLED
7 years ago
5f589c33f4
USB directly to FPGA for possible USB1.1 core
7 years ago
236f63488a
DIP SWITCH routed
7 years ago
2153a220a0
schematic symbol for ADC MAX11123
...
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
7 years ago
be09416928
Add 27 ohm resistors in series with FTDI USB and readme update
8 years ago
81b3ea5da0
adding minimal set of 3 2.2uF capacitor for 1.2V, 2.5V and 3.3V
8 years ago
ee7d266543
Resistors for LEDs
8 years ago
18aef04f2c
JTAG header
8 years ago
238ad770ce
moving USB LEDs on TOP layer
8 years ago
dcbf46dff2
optimizing PCB
8 years ago
b7500cc477
increasing thickness of power traces, moving clock
...
to a bank which is always at 3.3V
8 years ago
2a60828a99
schem. pullup 1.5k for USB 1.1 full speed mode
8 years ago
1a122bfc67
fully routed
8 years ago
dbf4b92a22
audio DAC routed
8 years ago
23b588ff16
Routing... 4 routes remaining
8 years ago
0f9d00f602
Buffer capacitor for SDRAM
8 years ago
dcbfda0556
Run DRC to update cupper fill zones
8 years ago
9d6f8bf493
improving SD card power supply and replacing with
...
suitable schematic symbol for micro SD card (was normal SD card)
8 years ago
5590ba802d
optimizing routing for SD and FTDI
8 years ago
1e5e0b01a6
connecting JTAG lines to FTDI serial lines RI DCD CTS DSR
...
as those pins are by default inputs and can be reconfigured as outputs
similar but not identical pinout as the one that works from ujprog
CBUS used to force-wakeup of the board from sleep state
2 LEDs to CBUS pins to display usb enumeration and activity status
8 years ago
5e953da6b9
connecting required pins for WiFi programming
8 years ago
davor