marlin-lulzbot-laser/Marlin/pins.h

#ifndef PINS_H
#define PINS_H

#if MOTHERBOARD == 99
#define	KNOWN_BOARD 1

#define X_STEP_PIN          2
#define X_DIR_PIN           3
#define X_ENABLE_PIN        -1
#define X_MIN_PIN           -1
#define X_MAX_PIN           16

#define Y_STEP_PIN          5
#define Y_DIR_PIN           6
#define Y_ENABLE_PIN       -1
#define Y_MIN_PIN           67
#define Y_MAX_PIN          -1

#define Z_STEP_PIN          62
#define Z_DIR_PIN           63
#define Z_ENABLE_PIN       -1
#define Z_MIN_PIN           59
#define Z_MAX_PIN          -1

#define E0_STEP_PIN         65
#define E0_DIR_PIN          66
#define E0_ENABLE_PIN      -1

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            -1
#define FAN_PIN            -1
#define PS_ON_PIN           9
#define KILL_PIN           -1

#define HEATER_0_PIN        13
#define HEATER_1_PIN       -1
#define HEATER_2_PIN       -1
#define TEMP_0_PIN          6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN         -1   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_2_PIN         -1   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_BED_PIN      4
#define TEMP_BED_PIN       10

#endif /* 99 */

/****************************************************************************************
* Gen7 v1.1, v1.2, v1.3, v1.4 pin assignment
*
****************************************************************************************/


#if MOTHERBOARD == 13
#define MOTHERBOARD 11
#define GEN7_VERSION 14 // v1.4
#endif

#if MOTHERBOARD == 12
#define MOTHERBOARD 11
#define GEN7_VERSION 13 // v1.3
#endif

#if MOTHERBOARD == 11
#define KNOWN_BOARD

#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.

#endif

#ifndef GEN7_VERSION
#define GEN7_VERSION 12 // v1.x
#endif

//x axis pins
#define X_STEP_PIN 19
#define X_DIR_PIN 18
#define X_ENABLE_PIN 24
#define X_MIN_PIN 7
#define X_MAX_PIN -1

//y axis pins
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_MIN_PIN 5
#define Y_MAX_PIN -1

//z axis pins
#define Z_STEP_PIN 26
#define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24
#define Z_MIN_PIN 1
#define Z_MAX_PIN 0

//extruder pins
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24

#define TEMP_0_PIN 1
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 2

#define HEATER_0_PIN 4
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 3


#define SDPOWER -1
#define SDSS -1 // SCL pin of I2C header
#define LED_PIN -1

#if (GEN7_VERSION >= 13)
// Gen7 v1.3 removed the fan pin
#define FAN_PIN -1
#else
#define FAN_PIN 31
#endif
#define PS_ON_PIN 15

#if (GEN7_VERSION < 14)
// Gen 1.3 and earlier supplied thermistor power via PS_ON
// Need to ignore the bad thermistor readings on those units
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
#endif

//our pin for debugging.
#define DEBUG_PIN 0

//our RS485 pins
#define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13

#endif

/*******************************************************************************
*********
* Gen7 Alfons3  pin assignment
*
********************************************************************************
********/
/* These Pins are assigned for the modified GEN7 Board from Alfons3 Please review the pins and adjust it for your needs*/

#if MOTHERBOARD == 10
#define KNOWN_BOARD

#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
    #error Oops!  Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.

#endif

//x axis pins
    #define X_STEP_PIN      21                  //different from stanard GEN7
    #define X_DIR_PIN       20				    //different from stanard GEN7
    #define X_ENABLE_PIN    24
    #define X_MIN_PIN       0
    #define X_MAX_PIN       -1

    //y axis pins
    #define Y_STEP_PIN      23
    #define Y_DIR_PIN       22
    #define Y_ENABLE_PIN    24
    #define Y_MIN_PIN       1
    #define Y_MAX_PIN       -1

    //z axis pins
    #define Z_STEP_PIN      26
    #define Z_DIR_PIN       25
    #define Z_ENABLE_PIN    24
    #define Z_MIN_PIN       2
    #define Z_MAX_PIN       -1

    //extruder pins
    #define E0_STEP_PIN      28
    #define E0_DIR_PIN       27
    #define E0_ENABLE_PIN    24
    
    #define TEMP_0_PIN      2
    #define TEMP_1_PIN      -1
    #define TEMP_2_PIN      -1
    #define TEMP_BED_PIN        1   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
     
    #define HEATER_0_PIN    4
    #define HEATER_1_PIN    -1   
    #define HEATER_2_PIN    -1
    #define HEATER_BED_PIN      3  // (bed)

    #define SDPOWER         -1
    #define SDSS            31                  // SCL pin of I2C header || CS Pin for SD Card support
    #define LED_PIN         -1

    #define FAN_PIN         -1
    #define PS_ON_PIN       19
    //our pin for debugging.

    #define DEBUG_PIN        -1

    //our RS485 pins
    //#define TX_ENABLE_PIN       12
    //#define RX_ENABLE_PIN       13
    
    #define BEEPER -1	
	#define SDCARDDETECT -1 		
    #define SUICIDE_PIN -1						//has to be defined; otherwise Power_off doesn't work
	
	//Pins for 4bit LCD Support 
    #define LCD_PINS_RS 18 
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 16
    #define LCD_PINS_D5 15 
    #define LCD_PINS_D6 13
    #define LCD_PINS_D7 14
    
     //buttons are directly attached
    #define BTN_EN1 11
    #define BTN_EN2 10
    #define BTN_ENC 12  //the click
    
    #define BLEN_C 2
    #define BLEN_B 1
    #define BLEN_A 0

    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1
#endif

/****************************************************************************************
* Arduino Mega pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34
#define KNOWN_BOARD 1

//////////////////FIX THIS//////////////
#ifndef __AVR_ATmega1280__
 #ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
#endif

// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1
// #define RAMPS_V_1_3
// #define RAMPS_V_1_0

#ifdef MOTHERBOARD == 33 || MOTHERBOARD == 34

#define X_STEP_PIN         54
#define X_DIR_PIN          55
#define X_ENABLE_PIN       38
#define X_MIN_PIN           3
#define X_MAX_PIN           2   //2 //Max endstops default to disabled "-1", set to commented value to enable.

#define Y_STEP_PIN         60
#define Y_DIR_PIN          61
#define Y_ENABLE_PIN       56
#define Y_MIN_PIN          14
#define Y_MAX_PIN          15   //15

#define Z_STEP_PIN         46
#define Z_DIR_PIN          48
#define Z_ENABLE_PIN       62
#define Z_MIN_PIN          18
#define Z_MAX_PIN          19

#define E0_STEP_PIN        26
#define E0_DIR_PIN         28
#define E0_ENABLE_PIN      24

#define E1_STEP_PIN        36
#define E1_DIR_PIN         34
#define E1_ENABLE_PIN      30

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13

#if MOTHERBOARD == 33
#define FAN_PIN            9 // (Sprinter config)
#else
#define FAN_PIN            4 // IO pin. Buffer needed
#endif
#define PS_ON_PIN          12
#define KILL_PIN           -1

#define HEATER_0_PIN       10   // EXTRUDER 1
#if MOTHERBOARD == 33
#define HEATER_1_PIN       -1
#else
#define HEATER_1_PIN       9    // EXTRUDER 2 (FAN On Sprinter)
#endif
#define HEATER_2_PIN       -1   
#define TEMP_0_PIN         13   // ANALOG NUMBERING
#define TEMP_1_PIN         15   // ANALOG NUMBERING
#define TEMP_2_PIN         -1   // ANALOG NUMBERING
#define HEATER_BED_PIN     8    // BED
#define TEMP_BED_PIN       14   // ANALOG NUMBERING

#ifdef ULTRA_LCD

  #ifdef NEWPANEL
  //arduino pin which triggers an piezzo beeper
    #define BEEPER 33			// Beeper on AUX-4

    #define LCD_PINS_RS 16 
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25 
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
    
    //buttons are directly attached using AUX-2
    #define BTN_EN1 44
    #define BTN_EN2 42
    #define BTN_ENC 64  //the click
    
    #define BLEN_C 2
    #define BLEN_B 1
    #define BLEN_A 0
    
    #define SDCARDDETECT 31		// Ramps does not use this port
    
      //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1

  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 33		No Beeper added

    //buttons are attached to a shift register
	// Not wired this yet
    //#define SHIFT_CLK 38
    //#define SHIFT_LD 42
    //#define SHIFT_OUT 40
    //#define SHIFT_EN 17
    
    #define LCD_PINS_RS 16 
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25 
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
    
    //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1

    
    //bits in the shift register that carry the buttons for:
    // left up center down right red
    #define BL_LE 7
    #define BL_UP 6
    #define BL_MI 5
    #define BL_DW 4
    #define BL_RI 3
    #define BL_ST 2

    #define BLEN_B 1
    #define BLEN_A 0
  #endif 
#endif //ULTRA_LCD

#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default

#define X_STEP_PIN         26
#define X_DIR_PIN          28
#define X_ENABLE_PIN       24
#define X_MIN_PIN           3
#define X_MAX_PIN          -1    //2

#define Y_STEP_PIN         38
#define Y_DIR_PIN          40
#define Y_ENABLE_PIN       36
#define Y_MIN_PIN          16
#define Y_MAX_PIN          -1    //17

#define Z_STEP_PIN         44
#define Z_DIR_PIN          46
#define Z_ENABLE_PIN       42
#define Z_MIN_PIN          18
#define Z_MAX_PIN          -1    //19

#define E0_STEP_PIN         32
#define E0_DIR_PIN          34
#define E0_ENABLE_PIN       30

#define SDPOWER            48
#define SDSS               53
#define LED_PIN            13
#define PS_ON_PIN          -1
#define KILL_PIN           -1



#ifdef RAMPS_V_1_0 // RAMPS_V_1_0
  #define HEATER_0_PIN     12    // RAMPS 1.0
  #define HEATER_BED_PIN   -1    // RAMPS 1.0
  #define FAN_PIN          11    // RAMPS 1.0
#else // RAMPS_V_1_1 or RAMPS_V_1_2
  #define HEATER_0_PIN     10    // RAMPS 1.1
  #define HEATER_BED_PIN    8    // RAMPS 1.1
  #define FAN_PIN           9    // RAMPS 1.1
#endif
#define HEATER_1_PIN        -1
#define HEATER_2_PIN        -1
#define TEMP_0_PIN          2    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN          -1   
#define TEMP_2_PIN          -1   
#define TEMP_BED_PIN        1    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#endif

// SPI for Max6675 Thermocouple 

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support  
  #define MAX_SCK_PIN          52
  #define MAX_MISO_PIN         50
  #define MAX_MOSI_PIN         51
  #define MAX6675_SS       53
#else
  #define MAX6675_SS       49
#endif

#endif

/****************************************************************************************
* Duemilanove w/ ATMega328P pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 4
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega328P__
#error Oops!  Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
#endif

#define X_STEP_PIN         19
#define X_DIR_PIN          18
#define X_ENABLE_PIN       -1
#define X_MIN_PIN          17
#define X_MAX_PIN          -1

#define Y_STEP_PIN         10
#define Y_DIR_PIN           7
#define Y_ENABLE_PIN       -1
#define Y_MIN_PIN           8
#define Y_MAX_PIN          -1

#define Z_STEP_PIN         13
#define Z_DIR_PIN           3
#define Z_ENABLE_PIN        2
#define Z_MIN_PIN           4
#define Z_MAX_PIN          -1

#define E0_STEP_PIN         11
#define E0_DIR_PIN          12
#define E0_ENABLE_PIN       -1

#define SDPOWER          -1
#define SDSS          -1
#define LED_PIN            -1
#define FAN_PIN             5
#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define HEATER_0_PIN        6
#define HEATER_1_PIN        -1
#define HEATER_2_PIN        -1
#define TEMP_0_PIN          0    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN          -1    
#define TEMP_2_PIN          -1    
#define HEATER_BED_PIN      -1
#define TEMP_BED_PIN        -1

#endif

/****************************************************************************************
* Gen6 pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 5 || MOTHERBOARD == 51
#define KNOWN_BOARD 1

#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

//x axis pins
    #define X_STEP_PIN      15
    #define X_DIR_PIN       18
    #define X_ENABLE_PIN    19
    #define X_MIN_PIN       20
    #define X_MAX_PIN       -1
    
    //y axis pins
    #define Y_STEP_PIN      23
    #define Y_DIR_PIN       22
    #define Y_ENABLE_PIN    24
    #define Y_MIN_PIN       25
    #define Y_MAX_PIN       -1
    
    //z axis pins
    #define Z_STEP_PIN      27
    #define Z_DIR_PIN       28
    #define Z_ENABLE_PIN    29
    #define Z_MIN_PIN       30
    #define Z_MAX_PIN       -1
    
    //extruder pins
    #define E0_STEP_PIN      4    //Edited @ EJE Electronics 20100715
    #define E0_DIR_PIN       2    //Edited @ EJE Electronics 20100715
    #define E0_ENABLE_PIN    3    //Added @ EJE Electronics 20100715
    #define TEMP_0_PIN      5     //changed @ rkoeppl 20110410
    #define TEMP_1_PIN      -1    //changed @ rkoeppl 20110410


    #define TEMP_2_PIN      -1    //changed @ rkoeppl 20110410
    #define HEATER_0_PIN    14    //changed @ rkoeppl 20110410
    #define HEATER_1_PIN    -1
    #define HEATER_2_PIN    -1
    #if MOTHERBOARD == 5
    #define HEATER_BED_PIN  -1    //changed @ rkoeppl 20110410
    #define TEMP_BED_PIN    -1    //changed @ rkoeppl 20110410
    #else
    #define HEATER_BED_PIN   1    //changed @ rkoeppl 20110410
    #define TEMP_BED_PIN     0    //changed @ rkoeppl 20110410
    #endif
    #define SDPOWER          -1
    #define SDSS          17
    #define LED_PIN         -1    //changed @ rkoeppl 20110410
    #define FAN_PIN         -1    //changed @ rkoeppl 20110410
    #define PS_ON_PIN       -1    //changed @ rkoeppl 20110410
    //our pin for debugging.
    
    #define DEBUG_PIN        0
    
    //our RS485 pins
    #define TX_ENABLE_PIN	12
    #define RX_ENABLE_PIN	13

    
#endif

/****************************************************************************************
* Sanguinololu pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 62
#undef MOTHERBOARD
#define MOTHERBOARD 6
#define SANGUINOLOLU_V_1_2 
#endif
#if MOTHERBOARD == 6
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

#define X_STEP_PIN         15
#define X_DIR_PIN          21
#define X_MIN_PIN          18
#define X_MAX_PIN           -1

#define Y_STEP_PIN         22
#define Y_DIR_PIN          23
#define Y_MIN_PIN          19
#define Y_MAX_PIN          -1

#define Z_STEP_PIN         3
#define Z_DIR_PIN          2
#define Z_MIN_PIN          20
#define Z_MAX_PIN          -1

#define E0_STEP_PIN         1
#define E0_DIR_PIN          0

#define LED_PIN            -1

#define FAN_PIN            -1 

#define PS_ON_PIN          -1
#define KILL_PIN           -1

#define HEATER_0_PIN       13 // (extruder)
#define HEATER_1_PIN       -1
#define HEATER_2_PIN       -1

#ifdef SANGUINOLOLU_V_1_2

#define HEATER_BED_PIN     12 // (bed)
#define X_ENABLE_PIN       14
#define Y_ENABLE_PIN       14
#define Z_ENABLE_PIN       26
#define E0_ENABLE_PIN       14

#else

#define HEATER_BED_PIN       14  // (bed)
#define X_ENABLE_PIN       -1
#define Y_ENABLE_PIN       -1
#define Z_ENABLE_PIN       -1
#define E0_ENABLE_PIN       -1

#endif

#define TEMP_0_PIN          7   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define TEMP_1_PIN         -1
#define TEMP_2_PIN         -1
#define TEMP_BED_PIN        6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define SDPOWER            -1
#define SDSS               31

#endif


#if MOTHERBOARD == 7
#define KNOWN_BOARD
/*****************************************************************
* Ultimaker pin assignment
******************************************************************/

#ifndef __AVR_ATmega1280__
 #ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
#endif

#define X_STEP_PIN 25
#define X_DIR_PIN 23
#define X_MIN_PIN 22
#define X_MAX_PIN 24
#define X_ENABLE_PIN 27

#define Y_STEP_PIN 31
#define Y_DIR_PIN 33
#define Y_MIN_PIN 26
#define Y_MAX_PIN 28
#define Y_ENABLE_PIN 29

#define Z_STEP_PIN 37 
#define Z_DIR_PIN 39
#define Z_MIN_PIN 30
#define Z_MAX_PIN 32
#define Z_ENABLE_PIN 35

#define HEATER_BED_PIN 4 
#define TEMP_BED_PIN 10  

#define HEATER_0_PIN  2
#define TEMP_0_PIN 8   

#define HEATER_1_PIN 3
#define TEMP_1_PIN 9

#define HEATER_2_PIN -1
#define TEMP_2_PIN -1

#define E0_STEP_PIN         43
#define E0_DIR_PIN          45
#define E0_ENABLE_PIN       41

#define E1_STEP_PIN         49
#define E1_DIR_PIN          47
#define E1_ENABLE_PIN       51

#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13
#define FAN_PIN            7
#define PS_ON_PIN          12
#define KILL_PIN           -1
#define SUICIDE_PIN        54  //PIN that has to be turned on right after start, to keep power flowing.

#ifdef ULTRA_LCD

  #ifdef NEWPANEL
  //arduino pin witch triggers an piezzo beeper
    #define BEEPER 18

    #define LCD_PINS_RS 20 
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 16
    #define LCD_PINS_D5 21 
    #define LCD_PINS_D6 5
    #define LCD_PINS_D7 6
    
    //buttons are directly attached
    #define BTN_EN1 40
    #define BTN_EN2 42
    #define BTN_ENC 19  //the click
    
    #define BLEN_C 2
    #define BLEN_B 1
    #define BLEN_A 0
    
    #define SDCARDDETECT 38
    
      //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1
  #else //old style panel with shift register
    //arduino pin witch triggers an piezzo beeper
    #define BEEPER 18

    //buttons are attached to a shift register
    #define SHIFT_CLK 38
    #define SHIFT_LD 42
    #define SHIFT_OUT 40
    #define SHIFT_EN 17
    
    #define LCD_PINS_RS 16 
    #define LCD_PINS_ENABLE 5
    #define LCD_PINS_D4 6
    #define LCD_PINS_D5 21 
    #define LCD_PINS_D6 20
    #define LCD_PINS_D7 19
    
    //encoder rotation values
    #define encrot0 0
    #define encrot1 2
    #define encrot2 3
    #define encrot3 1

    
    //bits in the shift register that carry the buttons for:
    // left up center down right red
    #define BL_LE 7
    #define BL_UP 6
    #define BL_MI 5
    #define BL_DW 4
    #define BL_RI 3
    #define BL_ST 2

    #define BLEN_B 1
    #define BLEN_A 0
  #endif 
#endif //ULTRA_LCD

#endif

#if MOTHERBOARD == 71
#define KNOWN_BOARD
/*****************************************************************
* Ultimaker pin assignment (Old electronics)
******************************************************************/

#ifndef __AVR_ATmega1280__
 #ifndef __AVR_ATmega2560__
 #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
#endif

#define X_STEP_PIN 25
#define X_DIR_PIN 23
#define X_MIN_PIN 15
#define X_MAX_PIN 14
#define X_ENABLE_PIN 27

#define Y_STEP_PIN 31
#define Y_DIR_PIN 33
#define Y_MIN_PIN 17
#define Y_MAX_PIN 16
#define Y_ENABLE_PIN 29

#define Z_STEP_PIN 37 
#define Z_DIR_PIN 39
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
#define Z_ENABLE_PIN 35

#define HEATER_BED_PIN -1 
#define TEMP_BED_PIN -1  

#define HEATER_0_PIN  2
#define TEMP_0_PIN 8   

#define HEATER_1_PIN 1
#define TEMP_1_PIN 1

#define HEATER_2_PIN -1
#define TEMP_2_PIN -1

#define E0_STEP_PIN         43
#define E0_DIR_PIN          45
#define E0_ENABLE_PIN       41

#define E1_STEP_PIN         -1
#define E1_DIR_PIN          -1
#define E1_ENABLE_PIN       -1

#define SDPOWER            -1
#define SDSS               -1
#define LED_PIN            -1
#define FAN_PIN            -1
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.

#define LCD_PINS_RS 24 
#define LCD_PINS_ENABLE 22
#define LCD_PINS_D4 36
#define LCD_PINS_D5 34 
#define LCD_PINS_D6 32
#define LCD_PINS_D7 30

#endif

/****************************************************************************************
* Teensylu 0.7 pin assingments (ATMEGA90USB)
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
****************************************************************************************/
#if MOTHERBOARD == 8
#define MOTHERBOARD 8
#define KNOWN_BOARD 1


#define X_STEP_PIN          0  
#define X_DIR_PIN           1  
#define X_ENABLE_PIN       39 
#define X_MIN_PIN          13 
#define X_MAX_PIN          -1    

#define Y_STEP_PIN          2  
#define Y_DIR_PIN           3 
#define Y_ENABLE_PIN       38 
#define Y_MIN_PIN          14 
#define Y_MAX_PIN          -1    

#define Z_STEP_PIN          4
#define Z_DIR_PIN           5 
#define Z_ENABLE_PIN       23 
#define Z_MIN_PIN          15 
#define Z_MAX_PIN          -1    

#define E0_STEP_PIN         6  
#define E0_DIR_PIN          7 
#define E0_ENABLE_PIN       19 



#define HEATER_0_PIN       21  // Extruder
#define HEATER_1_PIN       -1
#define HEATER_2_PIN       -1
#define HEATER_BED_PIN     20  // Bed
#define FAN_PIN            22  // Fan   

#define TEMP_0_PIN          7  // Extruder
#define TEMP_1_PIN         -1
#define TEMP_2_PIN         -1
#define TEMP_BED_PIN        6  // Bed

#define SDPOWER            -1
#define SDSS                8
#define LED_PIN            -1
#define PS_ON_PIN          -1
#define KILL_PIN           -1 
#define ALARM_PIN          -1

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support  
  #define SCK_PIN           9 
  #define MISO_PIN         11 
  #define MOSI_PIN         10 
#endif
#endif

/****************************************************************************************
* Gen3+ pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 9
#define MOTHERBOARD 6
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#ifndef __AVR_ATmega1284P__
#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#endif

#define X_STEP_PIN         15
#define X_DIR_PIN          18
#define X_MIN_PIN          20
#define X_MAX_PIN           -1

#define Y_STEP_PIN         23
#define Y_DIR_PIN          22
#define Y_MIN_PIN          25
#define Y_MAX_PIN          -1

#define Z_STEP_PIN         27
#define Z_DIR_PIN          28
#define Z_MIN_PIN          30
#define Z_MAX_PIN          -1

#define E_STEP_PIN         17
#define E_DIR_PIN          21

#define LED_PIN            -1

#define FAN_PIN            -1 

#define PS_ON_PIN         14
#define KILL_PIN           -1

#define HEATER_0_PIN       12 // (extruder)

#define HEATER_1_PIN       16 // (bed)
#define X_ENABLE_PIN       19
#define Y_ENABLE_PIN       24
#define Z_ENABLE_PIN       29
#define E_ENABLE_PIN       13

#define TEMP_0_PIN          0   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define TEMP_1_PIN          5   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define TEMP_2_PIN         -1
#define SDPOWER            -1
#define SDSS               4
#define HEATER_2_PIN       -1

#endif




#ifndef KNOWN_BOARD
#error Unknown MOTHERBOARD value in configuration.h
#endif

//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN
#if EXTRUDERS == 3
  #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN
  #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN
#elif EXTRUDERS == 2
  #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN
  #define _E2_PINS -1
#elif EXTRUDERS == 1
  #define _E1_PINS -1 
  #define _E2_PINS -1
#else
  #error Unsupported number of extruders
#endif
#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, LED_PIN, PS_ON_PIN, \
                        HEATER_0_PIN, HEATER_1_PIN, HEATER_2_PIN, \
                        HEATER_BED_PIN, FAN_PIN,                  \
                        _E0_PINS, _E1_PINS, _E2_PINS,             \
                        TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN, TEMP_BED_PIN }
#endif