You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

191 lines
4.3 KiB

/**
* Rambo pin assignments
*/
#ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
#endif
#define LARGE_FLASH true
// Servo support
#if HAS_SERVOS
#define SERVO0_PIN 22 //motor header MX1
#if NUM_SERVOS > 1
#define SERVO1_PIN 23 //Motor header MX2
#if NUM_SERVOS > 2
#define SERVO2_PIN 24 //Motor header MX3
#if NUM_SERVOS > 3
#define SERVO2_PIN 5 //pwm header pin 5
#endif
#endif
#endif
#endif
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
#undef X_MS1_PIN
#undef X_MS2_PIN
#undef Y_MS1_PIN
#undef Y_MS2_PIN
#undef Z_MS1_PIN
#undef Z_MS2_PIN
#undef E0_MS1_PIN
#undef E0_MS2_PIN
#undef E1_MS1_PIN
#undef E1_MS2_PIN
#define X_STEP_PIN 37
#define X_DIR_PIN 48
#define X_MIN_PIN 12
#define X_MAX_PIN 24
#define X_ENABLE_PIN 29
#define X_MS1_PIN 40
#define X_MS2_PIN 41
#define Y_STEP_PIN 36
#define Y_DIR_PIN 49
#define Y_MIN_PIN 11
#define Y_MAX_PIN 23
#define Y_ENABLE_PIN 28
#define Y_MS1_PIN 69
#define Y_MS2_PIN 39
#define Z_STEP_PIN 35
#define Z_DIR_PIN 47
#define Z_MIN_PIN 10
#define Z_MAX_PIN 30
#define Z_ENABLE_PIN 27
#define Z_MS1_PIN 68
#define Z_MS2_PIN 67
#define HEATER_BED_PIN 3
#define TEMP_BED_PIN 2
#define HEATER_0_PIN 9
#define TEMP_0_PIN 0
#define HEATER_1_PIN 7
#define TEMP_1_PIN 1
#if ENABLED(BARICUDA)
#define HEATER_2_PIN 6
#else
#define HEATER_2_PIN -1
#endif
#define TEMP_2_PIN -1
#define E0_STEP_PIN 34
#define E0_DIR_PIN 43
#define E0_ENABLE_PIN 26
#define E0_MS1_PIN 65
#define E0_MS2_PIN 66
#define E1_STEP_PIN 33
#define E1_DIR_PIN 42
#define E1_ENABLE_PIN 25
#define E1_MS1_PIN 63
#define E1_MS2_PIN 64
#undef DIGIPOTSS_PIN
#define DIGIPOTSS_PIN 38
#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 8
/**********************************************************
Fan Pins
Fan_0 8
Fan_1 6
Fan_2 2
***********************************************************/
#define PS_ON_PIN 4
#define KILL_PIN -1 //80 with Smart Controller LCD
#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing.
#if ENABLED(ULTRA_LCD)
#define KILL_PIN 80
#if ENABLED(NEWPANEL)
//arduino pin which triggers an piezzo beeper
#define BEEPER 79 // Beeper on AUX-4
#define LCD_PINS_RS 70
#define LCD_PINS_ENABLE 71
#define LCD_PINS_D4 72
#define LCD_PINS_D5 73
#define LCD_PINS_D6 74
#define LCD_PINS_D7 75
//buttons are directly attached using AUX-2
#define BTN_EN1 76
#define BTN_EN2 77
#define BTN_ENC 78 //the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT 81 // Ramps does not use this port
#else //!NEWPANEL - old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 33 No Beeper added
//buttons are attached to a shift register
// Not wired this yet
// #define SHIFT_CLK 38
// #define SHIFT_LD 42
// #define SHIFT_OUT 40
// #define SHIFT_EN 17
#define LCD_PINS_RS 75
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
#endif // !NEWPANEL
#endif // ULTRA_LCD
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 44
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 70
#define DOGLCD_CS 71
#define LCD_SCREEN_ROT_180
//The encoder and click button
#define BTN_EN1 85
#define BTN_EN2 84
#define BTN_ENC 83 //the click switch
#define SDCARDDETECT -1 // Pin 72 if using easy adapter board
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 22
#define STAT_LED_BLUE 32
#endif
#endif // VIKI2/miniVIKI
#if ENABLED(FILAMENT_SENSOR)
//Filip added pin for Filament sensor analog input
#define FILWIDTH_PIN 3
#endif