|
|
@ -88,7 +88,7 @@
|
|
|
|
// M29 - Stop SD write
|
|
|
|
// M29 - Stop SD write
|
|
|
|
// M30 - Delete file from SD (M30 filename.g)
|
|
|
|
// M30 - Delete file from SD (M30 filename.g)
|
|
|
|
// M31 - Output time since last M109 or SD card start to serial
|
|
|
|
// M31 - Output time since last M109 or SD card start to serial
|
|
|
|
// M42 - Change pin status via gcode. Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
|
|
|
|
// M42 - Change pin status via gcode
|
|
|
|
// M80 - Turn on Power Supply
|
|
|
|
// M80 - Turn on Power Supply
|
|
|
|
// M81 - Turn off Power Supply
|
|
|
|
// M81 - Turn off Power Supply
|
|
|
|
// M82 - Set E codes absolute (default)
|
|
|
|
// M82 - Set E codes absolute (default)
|
|
|
@ -125,7 +125,6 @@
|
|
|
|
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
|
|
|
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
|
|
|
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
|
|
|
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
|
|
|
// M503 - print the current settings (from memory not from eeprom)
|
|
|
|
// M503 - print the current settings (from memory not from eeprom)
|
|
|
|
|
|
|
|
|
|
|
|
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
|
|
|
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
|
|
|
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
|
|
|
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
|
|
|
// M907 - Set digital trimpot motor current using axis codes.
|
|
|
|
// M907 - Set digital trimpot motor current using axis codes.
|
|
|
@ -1501,19 +1500,12 @@ void process_commands()
|
|
|
|
Config_PrintSettings();
|
|
|
|
Config_PrintSettings();
|
|
|
|
}
|
|
|
|
}
|
|
|
|
break;
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
|
|
#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
|
|
|
#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
|
|
|
|
|
|
|
|
|
|
|
case 540:
|
|
|
|
case 540:
|
|
|
|
|
|
|
|
|
|
|
|
{
|
|
|
|
{
|
|
|
|
|
|
|
|
|
|
|
|
if(code_seen('S')) abort_on_endstop_hit = code_value() > 0;
|
|
|
|
if(code_seen('S')) abort_on_endstop_hit = code_value() > 0;
|
|
|
|
|
|
|
|
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
break;
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#ifdef FILAMENTCHANGEENABLE
|
|
|
|
#ifdef FILAMENTCHANGEENABLE
|
|
|
|
case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
|
|
|
case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
|
|
|