Cleanup formatting of some M codes

master
Scott Lahteine 10 years ago
parent 907e8e98e5
commit 01654bdec1

@ -73,7 +73,7 @@ M140 - Set bed target temp
M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work. M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work.
M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters). M200 - set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).: D<millimeters>-
M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
@ -84,9 +84,9 @@ M207 - Set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/h
M208 - Set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] M208 - Set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
M218 - Set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y> M218 - Set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
M220 S<factor in percent>- set speed factor override percentage M220 - Set speed factor override percentage: S<factor in percent>
M221 S<factor in percent>- set extrude factor override percentage M221 - Set extrude factor override percentage: S<factor in percent>
M226 P<pin number> S<pin state>- Wait until the specified pin reaches the state required M226 - Wait until the specified pin reaches the state required: P<pin number> S<pin state>
M240 - Trigger a camera to take a photograph M240 - Trigger a camera to take a photograph
M250 - Set LCD contrast C<contrast value> (value 0..63) M250 - Set LCD contrast C<contrast value> (value 0..63)
M280 - Set servo position absolute. P: servo index, S: angle or microseconds M280 - Set servo position absolute. P: servo index, S: angle or microseconds
@ -117,9 +117,6 @@ M907 - Set digital trimpot motor current using axis codes.
M908 - Control digital trimpot directly. M908 - Control digital trimpot directly.
M350 - Set microstepping mode. M350 - Set microstepping mode.
M351 - Toggle MS1 MS2 pins directly. M351 - Toggle MS1 MS2 pins directly.
M928 - Start SD logging (M928 filename.g) - ended by M29
M999 - Restart after being stopped by error
``` ```
## SCARA-specific M-Codes - May change to suit future G-code standards ## SCARA-specific M-Codes - May change to suit future G-code standards
``` ```

Loading…
Cancel
Save