Update ENSURE_SMOOTH_MOVES in all configs

Marlin/Configuration_adv.h

@@ -496,24 +496,33 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
-// Enabling ENSURE_SMOOTH_MOVES ensures your printer will never stutter (for example in circles with a short segments). That's done in two steps:
-// --1--
-// During short segments like in circles, the update of the LCD Display can take so long that the block buffer gets completely drained.
-// If that happens, the movement of the printer gets very jerky until a longer segment like a longer straight line allows the buffer
-// to be filled again. This small stops also effects print quality in a bad way.
-// Enable ENSURE_SMOOTH_MOVES to update the LCD only when there is enough time during a move to do so.
-// Note that this means the display will not show actual values during this time and your printer will also not react to buttons
-// pressed immediately, except ALWAYS_ALLOW_MENU is also enabled.
-// --2--
-// No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main loop to add a new block to the buffer, checking temps,
-// including all interruptions due to interrupts, but without LCD update. If we would allow shorter moves, the buffer would start continously draining.
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
 //#define ENSURE_SMOOTH_MOVES
 #if ENABLED(ENSURE_SMOOTH_MOVES)
-  //#define ALWAYS_ALLOW_MENU // If enabled, the menu will be always accessible.
-                              // WARNING: If the menu is entered or navigated during short moves, the printer will stutter like without ENSURE_SMOOTH_MOVES!
-  #define LCD_UPDATE_THRESHOLD 170 // Minimum duration in ms of the current segment to allow a LCD update.
-                                   // Default value is valid for graphical LCDs like the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER.
-  #define MIN_BLOCK_TIME 6 // Minimum duration in ms a single block has to take. You shouldn't need to modify this.
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
 #endif
 
 // @section extruder

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -509,6 +509,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/K8400/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -504,6 +504,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/delta/biv2.5/Configuration_adv.h

@@ -498,6 +498,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -498,6 +498,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -498,6 +498,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -503,6 +503,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -498,6 +498,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -496,6 +496,35 @@
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
 
+//
+// Ensure Smooth Moves
+//
+// Enable this option to prevent the machine from stuttering when printing multiple short segments.
+// This feature uses two strategies to eliminate stuttering:
+//
+// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets
+//    completely drained. When this happens pauses are introduced between short segments, and print moves
+//    will become jerky until a longer segment provides enough time for the buffer to be filled again.
+//    This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue
+//    by pausing the LCD until there's enough time to safely update.
+//
+//    NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive.
+//          Enable ALWAYS_ALLOW_MENU to keep the controller responsive.
+//
+// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main
+//    loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to
+//    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
+//    draining.
+//
+//#define ENSURE_SMOOTH_MOVES
+#if ENABLED(ENSURE_SMOOTH_MOVES)
+  //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
+                                   // WARNING: Menu navigation during short moves may cause stuttering!
+  #define LCD_UPDATE_THRESHOLD 170 // (ms) Minimum duration for the current segment to allow an LCD update.
+                                   // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER).
+  #define MIN_BLOCK_TIME 6         // (ms) Minimum duration of a single block. You shouldn't need to modify this.
+#endif
+
 // @section extruder
 
 // extruder advance constant (s2/mm3)