forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

smaller changes

Browse Source
master
Christian Thalhammer 13 years ago
parent 4cc8e37bf1
commit 0e3631ff4b
3 changed files with 304 additions and 88 deletions
Show Stats Download Patch File Download Diff File

45
Marlin/Configuration.h
Unescape View File

@ -4,8 +4,8 @@
// This determines the communication speed of the printer
#define BAUDRATE 250000
//#define BAUDRATE 115200
//#define BAUDRATE 250000
#define BAUDRATE 115200
//#define BAUDRATE 230400
#define EXTRUDERS 1
@ -26,11 +26,11 @@
// MEGA/RAMPS up to 1.2 = 3,
// RAMPS 1.3 = 33
// Gen6 = 5,
// Sanguinololu 1.2 and above = 62,
// Ultimaker = 7,
// Sanguinololu 1.2 and above = 62
// Gen7 = 77,
// Ultimaker = 7,
// Teensylu = 8
#define MOTHERBOARD 7
#define MOTHERBOARD 77
//===========================================================================
//=============================Thermal Settings ============================
@ -45,20 +45,20 @@
// 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01
//#define THERMISTORHEATER_0 3
#define THERMISTORHEATER_0 1
//#define THERMISTORHEATER_1 1
//#define THERMISTORHEATER_2 1
//#define HEATER_0_USES_THERMISTOR
#define HEATER_0_USES_THERMISTOR
//#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_0_USES_AD595
//#define HEATER_0_USES_AD595
//#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
// Select one of these only to define how the bed temp is read.
//#define THERMISTORBED 1
//#define BED_USES_THERMISTOR
#define THERMISTORBED 1
#define BED_USES_THERMISTOR
//#define BED_LIMIT_SWITCHING
#ifdef BED_LIMIT_SWITCHING
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
@ -75,10 +75,10 @@
// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30 // (seconds)
#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled
#define HEATER_0_MINTEMP 5
//#define HEATER_0_MINTEMP 5
//#define HEATER_1_MINTEMP 5
//#define HEATER_2_MINTEMP 5
//#define BED_MINTEMP 5
@ -184,9 +184,9 @@
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
@ -209,9 +209,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
//#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
//#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
@ -256,7 +256,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
#define DEFAULT_MINTRAVELFEEDRATE 0.0
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while
//printing high speed & high detail. It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
#define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
@ -321,9 +322,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
//#define ULTIPANEL
#define ULTIPANEL
#ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel
#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
@ -359,7 +360,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
#define PREVENT_DANGEROUS_EXTRUDE
#define EXTRUDE_MINTEMP 190
#define EXTRUDE_MINTEMP 0
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
@ -392,3 +393,5 @@ const int dropsegments=5; //everything with less than this number of steps will
#include "thermistortables.h"
#endif //__CONFIGURATION_H

2
Marlin/Marlin.pde
Unescape View File

@ -237,9 +237,11 @@ void setup_photpin()
void setup_powerhold()
{
#ifdef SUICIDE_PIN
#if (SUICIDE_PIN> -1)
SET_OUTPUT(SUICIDE_PIN);
WRITE(SUICIDE_PIN, HIGH);
#endif
#endif
}
void suicide()

223
Marlin/ultralcd.pde
Unescape View File

@ -527,23 +527,119 @@ void MainMenu::showAxisMove()
MENUITEM( lcdprintPGM(" Main \003") , BLOCK;status=Main_Menu;beepshort(); ) ;
break;
case ItemAM_X:
MENUITEM( lcdprintPGM(" X+") , BLOCK;enquecommand("G92 X0");enquecommand("G1 F700 X10");beepshort(); ) ;
// MENUITEM( lcdprintPGM(" X+") , BLOCK;enquecommand("G92 X0");enquecommand("G1 F700 X10");beepshort(); ) ;
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" X:");
lcd.setCursor(13,line);lcd.print(ftostr3(current_position[X_AXIS]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=current_position[X_AXIS];
}
else
{
enquecommand("G1 F700 X"+encoderpos);
encoderpos=activeline*lcdslow;
beepshort();
}
BLOCK;
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>200) encoderpos=200;
lcd.setCursor(13,line);lcd.print(current_position[X_AXIS]);
}
}
break;
case ItemAM_Y:
MENUITEM( lcdprintPGM(" Y+") , BLOCK;enquecommand("G92 Y0");enquecommand("G1 F700 Y10");beepshort(); ) ;
//MENUITEM( lcdprintPGM(" Y+") , BLOCK;enquecommand("G92 Y0");enquecommand("G1 F700 Y10");beepshort(); ) ;
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" Y:");
lcd.setCursor(13,line);lcd.print(ftostr3(current_position[Y_AXIS]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=current_position[Y_AXIS];
}
else
{
enquecommand("G1 F700 Y"+encoderpos);
encoderpos=activeline*lcdslow;
beepshort();
}
BLOCK;
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>200) encoderpos=200;
lcd.setCursor(13,line);lcd.print(current_position[Y_AXIS]);
}
}
break;
case ItemAM_Z:
MENUITEM( lcdprintPGM(" Z+") , BLOCK;enquecommand("G92 Z0");enquecommand("G1 F700 Z10");beepshort(); ) ;
//MENUITEM( lcdprintPGM(" Z+") , BLOCK;enquecommand("G92 Z0");enquecommand("G1 F700 Z10");beepshort(); ) ;
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" Z:");
lcd.setCursor(13,line);lcd.print(ftostr3(current_position[Z_AXIS]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=current_position[Z_AXIS];
}
else
{
enquecommand("G1 F700 Z"+encoderpos);
encoderpos=activeline*lcdslow;
beepshort();
}
BLOCK;
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>170) encoderpos=170;
lcd.setCursor(13,line);lcd.print(current_position[Z_AXIS]);
}
}
break;
case ItemAM_E:
MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E50");beepshort(); ) ;
MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E10");beepshort(); ) ;
break;
default:
break;
}
line++;
}
updateActiveLines(ItemAM_Z,encoderpos);
updateActiveLines(ItemAM_E,encoderpos);
}
enum {ItemT_exit,ItemT_speed,ItemT_flow,ItemT_nozzle,
@ -1189,7 +1285,7 @@ enum {
ItemCM_vmaxx, ItemCM_vmaxy, ItemCM_vmaxz, ItemCM_vmaxe,
ItemCM_vtravmin,ItemCM_vmin,
ItemCM_amaxx, ItemCM_amaxy, ItemCM_amaxz, ItemCM_amaxe,
ItemCM_aret,ItemCM_esteps
ItemCM_aret, ItemCM_xsteps,ItemCM_ysteps, ItemCM_zsteps, ItemCM_esteps
};
@ -1465,6 +1561,121 @@ void MainMenu::showControlMotion()
}
}break;
case ItemCM_xsteps://axis_steps_per_unit[i] = code_value();
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" X steps/mm:");
lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[0]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(int)axis_steps_per_unit[0];
}
else
{
float factor=float(encoderpos)/float(axis_steps_per_unit[0]);
position[X_AXIS]=lround(position[X_AXIS]*factor);
//current_position[3]*=factor;
axis_steps_per_unit[X_AXIS]= encoderpos;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<5) encoderpos=5;
if(encoderpos>9999) encoderpos=9999;
lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
}
}break;
case ItemCM_ysteps://axis_steps_per_unit[i] = code_value();
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" Y steps/mm:");
lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[1]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(int)axis_steps_per_unit[1];
}
else
{
float factor=float(encoderpos)/float(axis_steps_per_unit[1]);
position[Y_AXIS]=lround(position[Y_AXIS]*factor);
//current_position[3]*=factor;
axis_steps_per_unit[Y_AXIS]= encoderpos;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<5) encoderpos=5;
if(encoderpos>9999) encoderpos=9999;
lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
}
}break;
case ItemCM_zsteps://axis_steps_per_unit[i] = code_value();
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(" Z steps/mm:");
lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[2]));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(int)axis_steps_per_unit[2];
}
else
{
float factor=float(encoderpos)/float(axis_steps_per_unit[2]);
position[Z_AXIS]=lround(position[Z_AXIS]*factor);
//current_position[3]*=factor;
axis_steps_per_unit[Z_AXIS]= encoderpos;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<5) encoderpos=5;
if(encoderpos>9999) encoderpos=9999;
lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
}
}break;
case ItemCM_esteps://axis_steps_per_unit[i] = code_value();
{
if(force_lcd_update)

Write Preview
Loading…
Cancel
Save