forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Add 4th extruder

Browse Source
master
MagoKimbra 10 years ago
parent 54d5b52a2e
commit 0ebf896070
16 changed files with 611 additions and 216 deletions
Show Stats Download Patch File Download Diff File

30
Marlin/Configuration.h
Unescape View File

@ -44,7 +44,7 @@
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_ULTIMAKER
#define MOTHERBOARD BOARD_AZTEEG_X3_PRO
#endif
// Define this to set a custom name for your generic Mendel,
@ -104,9 +104,10 @@
// 147 is Pt100 with 4k7 pullup
// 110 is Pt100 with 1k pullup (non standard)
#define TEMP_SENSOR_0 -1
#define TEMP_SENSOR_1 -1
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_BED 0
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
@ -121,20 +122,22 @@
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5
#define HEATER_1_MINTEMP 5
#define HEATER_2_MINTEMP 5
#define BED_MINTEMP 5
#define HEATER_0_MINTEMP 5 // degC
#define HEATER_1_MINTEMP 5 // degC
#define HEATER_2_MINTEMP 5 // degC
#define HEATER_3_MINTEMP 5 // degC
#define BED_MINTEMP 5 // degC
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
#define HEATER_0_MAXTEMP 275 // degC
#define HEATER_1_MAXTEMP 275 // degC
#define HEATER_2_MAXTEMP 275 // degC
#define HEATER_3_MAXTEMP 275 // degC
#define BED_MAXTEMP 150 // degC
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
// If your bed has low resistance e.g. 0.6 ohm and throws the fuse you can duty cycle it to reduce the
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
@ -221,7 +224,7 @@
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MINTEMP 170
#define EXTRUDE_MINTEMP 170 // degC
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
/*================== Thermal Runaway Protection ==============================
@ -325,6 +328,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN

18
Marlin/ConfigurationStore.cpp
Unescape View File

@ -77,7 +77,7 @@ void Config_StoreSettings()
EEPROM_WRITE_VAR(i,zprobe_zoffset);
#ifdef PIDTEMP
float dummy = 0.0f;
for (int e = 0; e < 3; e++)
for (int e = 0; e < 4; e++)
{
if (e < EXTRUDERS)
{
@ -136,6 +136,9 @@ void Config_StoreSettings()
EEPROM_WRITE_VAR(i, filament_size[1]);
#if EXTRUDERS > 2
EEPROM_WRITE_VAR(i, filament_size[2]);
#if EXTRUDERS > 3
EEPROM_WRITE_VAR(i, filament_size[3]);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
@ -280,6 +283,11 @@ SERIAL_ECHOLNPGM("Scaling factors:");
SERIAL_ECHO_START;
SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]);
SERIAL_ECHOLN("");
#if EXTRUDERS > 3
SERIAL_ECHO_START;
SERIAL_ECHOPAIR(" M200 T3 D", filament_size[3]);
SERIAL_ECHOLN("");
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
} else {
@ -336,7 +344,7 @@ void Config_RetrieveSettings()
EEPROM_READ_VAR(i,zprobe_zoffset);
#ifdef PIDTEMP
float dummy = 0.0f;
for (int e = 0; e < 3; e++) // 3 = max extruders supported by marlin
for (int e = 0; e < 4; e++) // 4 = max extruders supported by marlin
{
if (e < EXTRUDERS)
{
@ -403,6 +411,9 @@ void Config_RetrieveSettings()
EEPROM_READ_VAR(i, filament_size[1]);
#if EXTRUDERS > 2
EEPROM_READ_VAR(i, filament_size[2]);
#if EXTRUDERS > 3
EEPROM_READ_VAR(i, filament_size[3]);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
calculate_volumetric_multipliers();
@ -508,6 +519,9 @@ void Config_ResetDefault()
filament_size[1] = DEFAULT_NOMINAL_FILAMENT_DIA;
#if EXTRUDERS > 2
filament_size[2] = DEFAULT_NOMINAL_FILAMENT_DIA;
#if EXTRUDERS > 3
filament_size[3] = DEFAULT_NOMINAL_FILAMENT_DIA;
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
calculate_volumetric_multipliers();

12
Marlin/Configuration_adv.h
Unescape View File

@ -78,6 +78,7 @@
#define EXTRUDER_0_AUTO_FAN_PIN -1
#define EXTRUDER_1_AUTO_FAN_PIN -1
#define EXTRUDER_2_AUTO_FAN_PIN -1
#define EXTRUDER_3_AUTO_FAN_PIN -1
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
@ -486,6 +487,10 @@ const unsigned int dropsegments=5; //everything with less than this number of st
#define THERMISTORHEATER_2 TEMP_SENSOR_2
#define HEATER_2_USES_THERMISTOR
#endif
#if TEMP_SENSOR_3 > 0
#define THERMISTORHEATER_3 TEMP_SENSOR_3
#define HEATER_3_USES_THERMISTOR
#endif
#if TEMP_SENSOR_BED > 0
#define THERMISTORBED TEMP_SENSOR_BED
#define BED_USES_THERMISTOR
@ -499,6 +504,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
#if TEMP_SENSOR_2 == -1
#define HEATER_2_USES_AD595
#endif
#if TEMP_SENSOR_3 == -1
#define HEATER_3_USES_AD595
#endif
#if TEMP_SENSOR_BED == -1
#define BED_USES_AD595
#endif
@ -517,6 +525,10 @@ const unsigned int dropsegments=5; //everything with less than this number of st
#undef HEATER_2_MINTEMP
#undef HEATER_2_MAXTEMP
#endif
#if TEMP_SENSOR_3 == 0
#undef HEATER_3_MINTEMP
#undef HEATER_3_MAXTEMP
#endif
#if TEMP_SENSOR_BED == 0
#undef BED_MINTEMP
#undef BED_MAXTEMP

7
Marlin/Marlin.h
Unescape View File

@ -170,6 +170,13 @@ void manage_inactivity(bool ignore_stepper_queue=false);
#define disable_e2() /* nothing */
#endif
#if (EXTRUDERS > 3) && defined(E3_ENABLE_PIN) && (E3_ENABLE_PIN > -1)
#define enable_e3() WRITE(E3_ENABLE_PIN, E_ENABLE_ON)
#define disable_e3() WRITE(E3_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e3() /* nothing */
#define disable_e3() /* nothing */
#endif
enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3, X_HEAD=4, Y_HEAD=5};

41
Marlin/Marlin_main.cpp
Unescape View File

@ -212,6 +212,9 @@ int extruder_multiply[EXTRUDERS] = {100
, 100
#if EXTRUDERS > 2
, 100
#if EXTRUDERS > 3
, 100
#endif
#endif
#endif
};
@ -221,6 +224,9 @@ float filament_size[EXTRUDERS] = { DEFAULT_NOMINAL_FILAMENT_DIA
, DEFAULT_NOMINAL_FILAMENT_DIA
#if EXTRUDERS > 2
, DEFAULT_NOMINAL_FILAMENT_DIA
#if EXTRUDERS > 3
, DEFAULT_NOMINAL_FILAMENT_DIA
#endif
#endif
#endif
};
@ -229,6 +235,9 @@ float volumetric_multiplier[EXTRUDERS] = {1.0
, 1.0
#if EXTRUDERS > 2
, 1.0
#if EXTRUDERS > 3
, 1.0
#endif
#endif
#endif
};
@ -274,6 +283,9 @@ int EtoPPressure=0;
, false
#if EXTRUDERS > 2
, false
#if EXTRUDERS > 3
, false
#endif
#endif
#endif
};
@ -282,6 +294,9 @@ int EtoPPressure=0;
, false
#if EXTRUDERS > 2
, false
#if EXTRUDERS > 3
, false
#endif
#endif
#endif
};
@ -293,7 +308,7 @@ int EtoPPressure=0;
float retract_recover_length = RETRACT_RECOVER_LENGTH;
float retract_recover_length_swap = RETRACT_RECOVER_LENGTH_SWAP;
float retract_recover_feedrate = RETRACT_RECOVER_FEEDRATE;
#endif
#endif // FWRETRACT
#ifdef ULTIPANEL
#ifdef PS_DEFAULT_OFF
@ -582,8 +597,8 @@ void setup()
SERIAL_ECHOLNPGM(STRING_CONFIG_H_AUTHOR);
SERIAL_ECHOPGM("Compiled: ");
SERIAL_ECHOLNPGM(__DATE__);
#endif
#endif
#endif // STRING_CONFIG_H_AUTHOR
#endif // STRING_VERSION_CONFIG_H
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_FREE_MEMORY);
SERIAL_ECHO(freeMemory());
@ -2895,8 +2910,11 @@ Sigma_Exit:
filament_size[1] = (filament_size[1] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[1]);
#if EXTRUDERS > 2
filament_size[2] = (filament_size[2] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[2]);
#endif
#endif
#if EXTRUDERS > 3
filament_size[3] = (filament_size[3] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[3]);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
volumetric_enabled = true;
}
} else {
@ -3025,6 +3043,9 @@ Sigma_Exit:
#endif
#if EXTRUDERS > 2
retracted[2]=false;
#endif
#if EXTRUDERS > 3
retracted[3]=false;
#endif
}break;
case 1:
@ -3036,6 +3057,9 @@ Sigma_Exit:
#endif
#if EXTRUDERS > 2
retracted[2]=false;
#endif
#if EXTRUDERS > 3
retracted[3]=false;
#endif
}break;
default:
@ -4680,7 +4704,10 @@ void calculate_volumetric_multipliers() {
volumetric_multiplier[1] = calculate_volumetric_multiplier(filament_size[1]);
#if EXTRUDERS > 2
volumetric_multiplier[2] = calculate_volumetric_multiplier(filament_size[2]);
#endif
#endif
#if EXTRUDERS > 3
volumetric_multiplier[3] = calculate_volumetric_multiplier(filament_size[3]);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
}

14
Marlin/language_en.h
Unescape View File

@ -21,14 +21,16 @@
#define MSG_PREHEAT_PLA0 "Preheat PLA 1"
#define MSG_PREHEAT_PLA1 "Preheat PLA 2"
#define MSG_PREHEAT_PLA2 "Preheat PLA 3"
#define MSG_PREHEAT_PLA012 "Preheat PLA All"
#define MSG_PREHEAT_PLA3 "Preheat PLA 4"
#define MSG_PREHEAT_PLA0123 "Preheat PLA All"
#define MSG_PREHEAT_PLA_BEDONLY "Preheat PLA Bed"
#define MSG_PREHEAT_PLA_SETTINGS "Preheat PLA conf"
#define MSG_PREHEAT_ABS "Preheat ABS"
#define MSG_PREHEAT_ABS0 "Preheat ABS 1"
#define MSG_PREHEAT_ABS1 "Preheat ABS 2"
#define MSG_PREHEAT_ABS2 "Preheat ABS 3"
#define MSG_PREHEAT_ABS012 "Preheat ABS All"
#define MSG_PREHEAT_ABS3 "Preheat ABS 4"
#define MSG_PREHEAT_ABS0123 "Preheat ABS All"
#define MSG_PREHEAT_ABS_BEDONLY "Preheat ABS Bed"
#define MSG_PREHEAT_ABS_SETTINGS "Preheat ABS conf"
#define MSG_COOLDOWN "Cooldown"
@ -43,6 +45,7 @@
#define MSG_MOVE_E "Extruder"
#define MSG_MOVE_E1 "Extruder2"
#define MSG_MOVE_E2 "Extruder3"
#define MSG_MOVE_E3 "Extruder4"
#define MSG_MOVE_01MM "Move 0.1mm"
#define MSG_MOVE_1MM "Move 1mm"
#define MSG_MOVE_10MM "Move 10mm"
@ -50,12 +53,14 @@
#define MSG_NOZZLE "Nozzle"
#define MSG_NOZZLE1 "Nozzle2"
#define MSG_NOZZLE2 "Nozzle3"
#define MSG_NOZZLE3 "Nozzle4"
#define MSG_BED "Bed"
#define MSG_FAN_SPEED "Fan speed"
#define MSG_FLOW "Flow"
#define MSG_FLOW0 "Flow 0"
#define MSG_FLOW1 "Flow 1"
#define MSG_FLOW2 "Flow 2"
#define MSG_FLOW3 "Flow 3"
#define MSG_CONTROL "Control"
#define MSG_MIN " \002 Min"
#define MSG_MAX " \002 Max"
@ -75,6 +80,10 @@
#define MSG_PID_I2 "PID-I E3"
#define MSG_PID_D2 "PID-D E3"
#define MSG_PID_C2 "PID-C E3"
#define MSG_PID_P3 "PID-P E4"
#define MSG_PID_I3 "PID-I E4"
#define MSG_PID_D3 "PID-D E4"
#define MSG_PID_C3 "PID-C E4"
#define MSG_ACC "Accel"
#define MSG_VXY_JERK "Vxy-jerk"
#define MSG_VZ_JERK "Vz-jerk"
@ -99,6 +108,7 @@
#define MSG_FILAMENT_SIZE_EXTRUDER_0 "Fil. Dia. 1"
#define MSG_FILAMENT_SIZE_EXTRUDER_1 "Fil. Dia. 2"
#define MSG_FILAMENT_SIZE_EXTRUDER_2 "Fil. Dia. 3"
#define MSG_FILAMENT_SIZE_EXTRUDER_3 "Fil. Dia. 4"
#define MSG_CONTRAST "LCD contrast"
#define MSG_STORE_EPROM "Store memory"
#define MSG_LOAD_EPROM "Load memory"

14
Marlin/language_it.h
Unescape View File

@ -21,14 +21,16 @@
#define MSG_PREHEAT_PLA0 "Preriscalda PLA 1"
#define MSG_PREHEAT_PLA1 "Preriscalda PLA 2"
#define MSG_PREHEAT_PLA2 "Preriscalda PLA 3"
#define MSG_PREHEAT_PLA012 "Prer. PLA Tutto"
#define MSG_PREHEAT_PLA3 "Preriscalda PLA 4"
#define MSG_PREHEAT_PLA0123 "Prer. PLA Tutto"
#define MSG_PREHEAT_PLA_BEDONLY "Prer. PLA Piatto"
#define MSG_PREHEAT_PLA_SETTINGS "Config. prer. PLA"
#define MSG_PREHEAT_ABS "Preriscalda ABS"
#define MSG_PREHEAT_ABS0 "Preriscalda ABS 1"
#define MSG_PREHEAT_ABS1 "Preriscalda ABS 2"
#define MSG_PREHEAT_ABS2 "Preriscalda ABS 3"
#define MSG_PREHEAT_ABS012 "Prer. ABS Tutto"
#define MSG_PREHEAT_ABS3 "Preriscalda ABS 4"
#define MSG_PREHEAT_ABS0123 "Prer. ABS Tutto"
#define MSG_PREHEAT_ABS_BEDONLY "Prer. ABS Piatto"
#define MSG_PREHEAT_ABS_SETTINGS "Config. prer. ABS"
#define MSG_COOLDOWN "Raffredda"
@ -43,6 +45,7 @@
#define MSG_MOVE_E "Estrusore"
#define MSG_MOVE_E1 "Estrusore 2"
#define MSG_MOVE_E2 "Estrusore 3"
#define MSG_MOVE_E3 "Estrusore 4"
#define MSG_MOVE_01MM "Muovi di 0.1mm"
#define MSG_MOVE_1MM "Muovi di 1mm"
#define MSG_MOVE_10MM "Muovi di 10mm"
@ -50,12 +53,14 @@
#define MSG_NOZZLE "Ugello"
#define MSG_NOZZLE1 "Ugello2"
#define MSG_NOZZLE2 "Ugello3"
#define MSG_NOZZLE3 "Ugello4"
#define MSG_BED "Piatto"
#define MSG_FAN_SPEED "Ventola"
#define MSG_FLOW "Flusso"
#define MSG_FLOW0 "Flusso 0"
#define MSG_FLOW1 "Flusso 1"
#define MSG_FLOW2 "Flusso 2"
#define MSG_FLOW3 "Flusso 3"
#define MSG_CONTROL "Controllo"
#define MSG_MIN " \002 Min:"
#define MSG_MAX " \002 Max:"
@ -75,6 +80,10 @@
#define MSG_PID_I2 "PID-I E3"
#define MSG_PID_D2 "PID-D E3"
#define MSG_PID_C2 "PID-C E3"
#define MSG_PID_P3 "PID-P E4"
#define MSG_PID_I3 "PID-I E4"
#define MSG_PID_D3 "PID-D E4"
#define MSG_PID_C3 "PID-C E4"
#define MSG_ACC "Accel."
#define MSG_VXY_JERK "Vxy-jerk"
#define MSG_VZ_JERK "Vz-jerk"
@ -99,6 +108,7 @@
#define MSG_FILAMENT_SIZE_EXTRUDER_0 "Diam. filo 1"
#define MSG_FILAMENT_SIZE_EXTRUDER_1 "Diam. filo 2"
#define MSG_FILAMENT_SIZE_EXTRUDER_2 "Diam. filo 3"
#define MSG_FILAMENT_SIZE_EXTRUDER_3 "Diam. filo 4"
#define MSG_CONTRAST "Contrasto LCD"
#define MSG_STORE_EPROM "Salva in EEPROM"
#define MSG_LOAD_EPROM "Carica da EEPROM"

16
Marlin/pins.h
Unescape View File

@ -2933,6 +2933,12 @@ Fan_2 2
#endif // CHEAPTRONIC
#ifndef HEATER_3_PIN
#define HEATER_3_PIN -1
#endif
#ifndef TEMP_3_PIN
#define TEMP_3_PIN -1
#endif
#ifndef KNOWN_BOARD
#error Unknown MOTHERBOARD value in configuration.h
@ -2950,6 +2956,11 @@ Fan_2 2
#else
#define _E2_PINS
#endif
#if EXTRUDERS > 3
#define _E3_PINS E3_STEP_PIN, E3_DIR_PIN, E3_ENABLE_PIN, HEATER_3_PIN,
#else
#define _E3_PINS
#endif
#ifdef X_STOP_PIN
#if X_HOME_DIR < 0
@ -2995,7 +3006,6 @@ Fan_2 2
#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, PS_ON_PIN, \
HEATER_BED_PIN, FAN_PIN, \
_E0_PINS _E1_PINS _E2_PINS \
analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
_E0_PINS _E1_PINS _E2_PINS _E3_PINS \
analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_3_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
#endif //__PINS_H

20
Marlin/planner.cpp
Unescape View File

@ -80,7 +80,7 @@ unsigned long axis_steps_per_sqr_second[NUM_AXIS];
matrix_3x3 plan_bed_level_matrix = {
1.0, 0.0, 0.0,
0.0, 1.0, 0.0,
0.0, 0.0, 1.0,
0.0, 0.0, 1.0
};
#endif // #ifdef ENABLE_AUTO_BED_LEVELING
@ -96,7 +96,7 @@ float autotemp_factor=0.1;
bool autotemp_enabled=false;
#endif
unsigned char g_uc_extruder_last_move[3] = {0,0,0};
unsigned char g_uc_extruder_last_move[4] = {0,0,0,0};
//===========================================================================
//=================semi-private variables, used in inline functions =====
@ -486,6 +486,7 @@ void check_axes_activity()
disable_e0();
disable_e1();
disable_e2();
disable_e3();
}
#if defined(FAN_PIN) && FAN_PIN > -1
#ifdef FAN_KICKSTART_TIME
@ -672,6 +673,7 @@ block->steps_y = labs((target[X_AXIS]-position[X_AXIS]) - (target[Y_AXIS]-positi
if(g_uc_extruder_last_move[0] > 0) g_uc_extruder_last_move[0]--;
if(g_uc_extruder_last_move[1] > 0) g_uc_extruder_last_move[1]--;
if(g_uc_extruder_last_move[2] > 0) g_uc_extruder_last_move[2]--;
if(g_uc_extruder_last_move[3] > 0) g_uc_extruder_last_move[3]--;
switch(extruder)
{
@ -681,6 +683,7 @@ block->steps_y = labs((target[X_AXIS]-position[X_AXIS]) - (target[Y_AXIS]-positi
if(g_uc_extruder_last_move[1] == 0) disable_e1();
if(g_uc_extruder_last_move[2] == 0) disable_e2();
if(g_uc_extruder_last_move[3] == 0) disable_e3();
break;
case 1:
enable_e1();
@ -688,6 +691,7 @@ block->steps_y = labs((target[X_AXIS]-position[X_AXIS]) - (target[Y_AXIS]-positi
if(g_uc_extruder_last_move[0] == 0) disable_e0();
if(g_uc_extruder_last_move[2] == 0) disable_e2();
if(g_uc_extruder_last_move[3] == 0) disable_e3();
break;
case 2:
enable_e2();
@ -695,6 +699,15 @@ block->steps_y = labs((target[X_AXIS]-position[X_AXIS]) - (target[Y_AXIS]-positi
if(g_uc_extruder_last_move[0] == 0) disable_e0();
if(g_uc_extruder_last_move[1] == 0) disable_e1();
if(g_uc_extruder_last_move[3] == 0) disable_e3();
break;
case 3:
enable_e3();
g_uc_extruder_last_move[3] = BLOCK_BUFFER_SIZE*2;
if(g_uc_extruder_last_move[0] == 0) disable_e0();
if(g_uc_extruder_last_move[1] == 0) disable_e1();
if(g_uc_extruder_last_move[2] == 0) disable_e2();
break;
}
}
@ -703,6 +716,7 @@ block->steps_y = labs((target[X_AXIS]-position[X_AXIS]) - (target[Y_AXIS]-positi
enable_e0();
enable_e1();
enable_e2();
enable_e3();
}
}
@ -866,7 +880,7 @@ Having the real displacement of the head, we can calculate the total movement le
long min_xy_segment_time =min(max_x_segment_time, max_y_segment_time);
if(min_xy_segment_time < MAX_FREQ_TIME)
speed_factor = min(speed_factor, speed_factor * (float)min_xy_segment_time / (float)MAX_FREQ_TIME);
#endif
#endif // XY_FREQUENCY_LIMIT
// Correct the speed
if( speed_factor < 1.0)

36
Marlin/stepper.cpp
Unescape View File

@ -55,7 +55,7 @@ volatile static unsigned long step_events_completed; // The number of step event
#ifdef ADVANCE
static long advance_rate, advance, final_advance = 0;
static long old_advance = 0;
static long e_steps[3];
static long e_steps[4];
#endif
static long acceleration_time, deceleration_time;
//static unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate;
@ -200,6 +200,8 @@ void checkHitEndstops()
setTargetHotend0(0);
setTargetHotend1(0);
setTargetHotend2(0);
setTargetHotend3(0);
setTargetBed(0);
}
#endif
}
@ -681,7 +683,7 @@ ISR(TIMER1_COMPA_vect)
WRITE_E_STEP(INVERT_E_STEP_PIN);
}
#endif //!ADVANCE
#endif
#endif // CONFIG_STEPPERS_TOSHIBA
step_events_completed += 1;
if(step_events_completed >= current_block->step_event_count) break;
}
@ -807,6 +809,22 @@ ISR(TIMER1_COMPA_vect)
}
}
#endif
#if EXTRUDERS > 3
if (e_steps[3] != 0) {
WRITE(E3_STEP_PIN, INVERT_E_STEP_PIN);
if (e_steps[3] < 0) {
WRITE(E3_DIR_PIN, INVERT_E3_DIR);
e_steps[3]++;
WRITE(E3_STEP_PIN, !INVERT_E_STEP_PIN);
}
else if (e_steps[3] > 0) {
WRITE(E3_DIR_PIN, !INVERT_E3_DIR);
e_steps[3]--;
WRITE(E3_STEP_PIN, !INVERT_E_STEP_PIN);
}
}
#endif
}
}
#endif // ADVANCE
@ -846,6 +864,9 @@ void st_init()
#if defined(E2_DIR_PIN) && (E2_DIR_PIN > -1)
SET_OUTPUT(E2_DIR_PIN);
#endif
#if defined(E3_DIR_PIN) && (E3_DIR_PIN > -1)
SET_OUTPUT(E3_DIR_PIN);
#endif
//Initialize Enable Pins - steppers default to disabled.
@ -887,6 +908,10 @@ void st_init()
SET_OUTPUT(E2_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E2_ENABLE_PIN,HIGH);
#endif
#if defined(E3_ENABLE_PIN) && (E3_ENABLE_PIN > -1)
SET_OUTPUT(E3_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E3_ENABLE_PIN,HIGH);
#endif
//endstops and pullups
@ -977,6 +1002,11 @@ void st_init()
WRITE(E2_STEP_PIN,INVERT_E_STEP_PIN);
disable_e2();
#endif
#if defined(E3_STEP_PIN) && (E3_STEP_PIN > -1)
SET_OUTPUT(E3_STEP_PIN);
WRITE(E3_STEP_PIN,INVERT_E_STEP_PIN);
disable_e3();
#endif
// waveform generation = 0100 = CTC
TCCR1B &= ~(1<<WGM13);
@ -1007,6 +1037,7 @@ void st_init()
e_steps[0] = 0;
e_steps[1] = 0;
e_steps[2] = 0;
e_steps[3] = 0;
TIMSK0 |= (1<<OCIE0A);
#endif //ADVANCE
@ -1068,6 +1099,7 @@ void finishAndDisableSteppers()
disable_e0();
disable_e1();
disable_e2();
disable_e3();
}
void quickStop()

6
Marlin/stepper.h
Unescape View File

@ -23,7 +23,11 @@
#include "planner.h"
#if EXTRUDERS > 2
#if EXTRUDERS > 3
#define WRITE_E_STEP(v) { if(current_block->active_extruder == 3) { WRITE(E3_STEP_PIN, v); } else { if(current_block->active_extruder == 2) { WRITE(E2_STEP_PIN, v); } else { if(current_block->active_extruder == 1) { WRITE(E1_STEP_PIN, v); } else { WRITE(E0_STEP_PIN, v); }}}}
#define NORM_E_DIR() { if(current_block->active_extruder == 3) { WRITE(E3_DIR_PIN, !INVERT_E3_DIR); } else { if(current_block->active_extruder == 2) { WRITE(E2_DIR_PIN, !INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, !INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, !INVERT_E0_DIR); }}}}
#define REV_E_DIR() { if(current_block->active_extruder == 3) { WRITE(E3_DIR_PIN, INVERT_E3_DIR); } else { if(current_block->active_extruder == 2) { WRITE(E2_DIR_PIN, INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, INVERT_E0_DIR); }}}}
#elif EXTRUDERS > 2
#define WRITE_E_STEP(v) { if(current_block->active_extruder == 2) { WRITE(E2_STEP_PIN, v); } else { if(current_block->active_extruder == 1) { WRITE(E1_STEP_PIN, v); } else { WRITE(E0_STEP_PIN, v); }}}
#define NORM_E_DIR() { if(current_block->active_extruder == 2) { WRITE(E2_DIR_PIN, !INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, !INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, !INVERT_E0_DIR); }}}
#define REV_E_DIR() { if(current_block->active_extruder == 2) { WRITE(E2_DIR_PIN, INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, INVERT_E0_DIR); }}}

218
Marlin/temperature.cpp
Unescape View File

@ -115,14 +115,16 @@ static volatile bool temp_meas_ready = false;
static unsigned long extruder_autofan_last_check;
#endif
#if EXTRUDERS > 3
#if EXTRUDERS > 4
# error Unsupported number of extruders
#elif EXTRUDERS > 3
# define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 }
#elif EXTRUDERS > 2
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2, v3 }
# define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 }
#elif EXTRUDERS > 1
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2 }
# define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 }
#else
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1 }
# define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 }
#endif
#ifdef PIDTEMP
@ -144,10 +146,10 @@ static volatile bool temp_meas_ready = false;
#endif //PIDTEMP
// Init min and max temp with extreme values to prevent false errors during startup
static int minttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP );
static int maxttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP );
static int minttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 0, 0, 0 );
static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 16383, 16383, 16383 );
static int minttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP, HEATER_3_RAW_LO_TEMP);
static int maxttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP, HEATER_3_RAW_HI_TEMP);
static int minttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 0, 0, 0, 0 );
static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 16383, 16383, 16383, 16383 );
//static int bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP; /* No bed mintemp error implemented?!? */
#ifdef BED_MAXTEMP
static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
@ -157,8 +159,8 @@ static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
static void *heater_ttbl_map[2] = {(void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE };
static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN };
#else
static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE );
static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN );
static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE, (void *)HEATER_3_TEMPTABLE );
static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN, HEATER_3_TEMPTABLE_LEN );
#endif
static float analog2temp(int raw, uint8_t e);
@ -166,8 +168,8 @@ static float analog2tempBed(int raw);
static void updateTemperaturesFromRawValues();
#ifdef WATCH_TEMP_PERIOD
int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0);
unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0);
#endif //WATCH_TEMP_PERIOD
#ifndef SOFT_PWM_SCALE
@ -200,7 +202,8 @@ void PID_autotune(float temp, int extruder, int ncycles)
#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1)
(defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1)
unsigned long extruder_autofan_last_check = millis();
#endif
@ -243,7 +246,8 @@ void PID_autotune(float temp, int extruder, int ncycles)
#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1)
(defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) || \
(defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1)
if(millis() - extruder_autofan_last_check > 2500) {
checkExtruderAutoFans();
extruder_autofan_last_check = millis();
@ -420,6 +424,19 @@ void checkExtruderAutoFans()
fanState |= 4;
}
#endif
#if defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1
if (current_temperature[3] > EXTRUDER_AUTO_FAN_TEMPERATURE)
{
if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN)
fanState |= 1;
else if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN)
fanState |= 2;
else if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_2_AUTO_FAN_PIN)
fanState |= 4;
else
fanState |= 8;
}
#endif
// update extruder auto fan states
#if defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1
@ -434,6 +451,12 @@ void checkExtruderAutoFans()
&& EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN)
setExtruderAutoFanState(EXTRUDER_2_AUTO_FAN_PIN, (fanState & 4) != 0);
#endif
#if defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1
if (EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN
&& EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN)
&& EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN)
setExtruderAutoFanState(EXTRUDER_3_AUTO_FAN_PIN, (fanState & 8) != 0);
#endif
}
#endif // any extruder auto fan pins set
@ -837,6 +860,9 @@ void tp_init()
#if defined(HEATER_2_PIN) && (HEATER_2_PIN > -1)
SET_OUTPUT(HEATER_2_PIN);
#endif
#if defined(HEATER_3_PIN) && (HEATER_3_PIN > -1)
SET_OUTPUT(HEATER_3_PIN);
#endif
#if defined(HEATER_BED_PIN) && (HEATER_BED_PIN > -1)
SET_OUTPUT(HEATER_BED_PIN);
#endif
@ -897,6 +923,13 @@ void tp_init()
DIDR2 |= 1<<(TEMP_2_PIN - 8);
#endif
#endif
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
#if TEMP_3_PIN < 8
DIDR0 |= 1 << TEMP_3_PIN;
#else
DIDR2 |= 1<<(TEMP_3_PIN - 8);
#endif
#endif
#if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1)
#if TEMP_BED_PIN < 8
DIDR0 |= 1<<TEMP_BED_PIN;
@ -987,6 +1020,28 @@ void tp_init()
}
#endif //MAXTEMP 2
#if (EXTRUDERS > 3) && defined(HEATER_3_MINTEMP)
minttemp[3] = HEATER_3_MINTEMP;
while(analog2temp(minttemp_raw[3], 3) < HEATER_3_MINTEMP) {
#if HEATER_3_RAW_LO_TEMP < HEATER_3_RAW_HI_TEMP
minttemp_raw[3] += OVERSAMPLENR;
#else
minttemp_raw[3] -= OVERSAMPLENR;
#endif
}
#endif //MINTEMP 3
#if (EXTRUDERS > 3) && defined(HEATER_3_MAXTEMP)
maxttemp[3] = HEATER_3_MAXTEMP;
while(analog2temp(maxttemp_raw[3], 3) > HEATER_3_MAXTEMP) {
#if HEATER_3_RAW_LO_TEMP < HEATER_3_RAW_HI_TEMP
maxttemp_raw[3] -= OVERSAMPLENR;
#else
maxttemp_raw[3] += OVERSAMPLENR;
#endif
}
#endif // MAXTEMP 3
#ifdef BED_MINTEMP
/* No bed MINTEMP error implemented?!? */ /*
while(analog2tempBed(bed_minttemp_raw) < BED_MINTEMP) {
@ -1075,6 +1130,7 @@ void thermal_runaway_protection(int *state, unsigned long *timer, float temperat
disable_e0();
disable_e1();
disable_e2();
disable_e3();
manage_heater();
lcd_update();
}
@ -1113,6 +1169,15 @@ void disable_heater()
#endif
#endif
#if defined(TEMP_3_PIN) && TEMP_3_PIN > -1 && EXTRUDERS > 3
target_temperature[3]=0;
soft_pwm[3]=0;
#if defined(HEATER_3_PIN) && HEATER_3_PIN > -1
WRITE(HEATER_3_PIN,LOW);
#endif
#endif
#if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1
target_temperature_bed=0;
soft_pwm_bed=0;
@ -1227,8 +1292,9 @@ ISR(TIMER0_COMPB_vect)
static unsigned long raw_temp_0_value = 0;
static unsigned long raw_temp_1_value = 0;
static unsigned long raw_temp_2_value = 0;
static unsigned long raw_temp_3_value = 0;
static unsigned long raw_temp_bed_value = 0;
static unsigned char temp_state = 10;
static unsigned char temp_state = 12;
static unsigned char pwm_count = (1 << SOFT_PWM_SCALE);
static unsigned char soft_pwm_0;
#ifdef SLOW_PWM_HEATERS
@ -1236,6 +1302,7 @@ ISR(TIMER0_COMPB_vect)
static unsigned char state_heater_0 = 0;
static unsigned char state_timer_heater_0 = 0;
#endif
#if (EXTRUDERS > 1) || defined(HEATERS_PARALLEL)
static unsigned char soft_pwm_1;
#ifdef SLOW_PWM_HEATERS
@ -1250,6 +1317,14 @@ ISR(TIMER0_COMPB_vect)
static unsigned char state_timer_heater_2 = 0;
#endif
#endif
#if EXTRUDERS > 3
static unsigned char soft_pwm_3;
#ifdef SLOW_PWM_HEATERS
static unsigned char state_heater_3 = 0;
static unsigned char state_timer_heater_3 = 0;
#endif
#endif
#if HEATER_BED_PIN > -1
static unsigned char soft_pwm_b;
#ifdef SLOW_PWM_HEATERS
@ -1283,6 +1358,12 @@ ISR(TIMER0_COMPB_vect)
soft_pwm_2 = soft_pwm[2];
if(soft_pwm_2 > 0) WRITE(HEATER_2_PIN,1); else WRITE(HEATER_2_PIN,0);
#endif
#if EXTRUDERS > 3
soft_pwm_3 = soft_pwm[3];
if(soft_pwm_3 > 0) WRITE(HEATER_3_PIN,1); else WRITE(HEATER_3_PIN,0);
#endif
#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1
soft_pwm_b = soft_pwm_bed;
if(soft_pwm_b > 0) WRITE(HEATER_BED_PIN,1); else WRITE(HEATER_BED_PIN,0);
@ -1298,12 +1379,17 @@ ISR(TIMER0_COMPB_vect)
WRITE(HEATER_1_PIN,0);
#endif
}
#if EXTRUDERS > 1
if(soft_pwm_1 < pwm_count) WRITE(HEATER_1_PIN,0);
#endif
#if EXTRUDERS > 2
if(soft_pwm_2 < pwm_count) WRITE(HEATER_2_PIN,0);
#endif
#if EXTRUDERS > 3
if(soft_pwm_3 < pwm_count) WRITE(HEATER_3_PIN,0);
#endif
#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1
if(soft_pwm_b < pwm_count) WRITE(HEATER_BED_PIN,0);
#endif
@ -1406,6 +1492,32 @@ ISR(TIMER0_COMPB_vect)
}
#endif
#if EXTRUDERS > 3
// EXTRUDER 3
soft_pwm_3 = soft_pwm[3];
if (soft_pwm_3 > 0) {
// turn ON heather only if the minimum time is up
if (state_timer_heater_3 == 0) {
// if change state set timer
if (state_heater_3 == 0) {
state_timer_heater_3 = MIN_STATE_TIME;
}
state_heater_3 = 1;
WRITE(HEATER_3_PIN, 1);
}
} else {
// turn OFF heather only if the minimum time is up
if (state_timer_heater_3 == 0) {
// if change state set timer
if (state_heater_3 == 1) {
state_timer_heater_3 = MIN_STATE_TIME;
}
state_heater_3 = 0;
WRITE(HEATER_3_PIN, 0);
}
}
#endif
#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1
// BED
soft_pwm_b = soft_pwm_bed;
@ -1479,6 +1591,21 @@ ISR(TIMER0_COMPB_vect)
}
#endif
#if EXTRUDERS > 3
// EXTRUDER 3
if (soft_pwm_3 < slow_pwm_count) {
// turn OFF heather only if the minimum time is up
if (state_timer_heater_3 == 0) {
// if change state set timer
if (state_heater_3 == 1) {
state_timer_heater_3 = MIN_STATE_TIME;
}
state_heater_3 = 0;
WRITE(HEATER_3_PIN, 0);
}
}
#endif
#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1
// BED
if (soft_pwm_b < slow_pwm_count) {
@ -1527,6 +1654,12 @@ ISR(TIMER0_COMPB_vect)
state_timer_heater_2--;
#endif
#if EXTRUDERS > 3
// Extruder 3
if (state_timer_heater_3 > 0)
state_timer_heater_3--;
#endif
#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1
// Bed
if (state_timer_heater_b > 0)
@ -1614,10 +1747,28 @@ ISR(TIMER0_COMPB_vect)
#if defined(TEMP_2_PIN) && (TEMP_2_PIN > -1)
raw_temp_2_value += ADC;
#endif
temp_state = 8;//change so that Filament Width is also measured
temp_state = 8;
break;
case 8: // Prepare TEMP_3
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
#if TEMP_3_PIN > 7
ADCSRB = 1<<MUX5;
#else
ADCSRB = 0;
#endif
ADMUX = ((1 << REFS0) | (TEMP_3_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
lcd_buttons_update();
temp_state = 9;
break;
case 9: // Measure TEMP_3
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
raw_temp_3_value += ADC;
#endif
temp_state = 10; //change so that Filament Width is also measured
break;
case 8: //Prepare FILWIDTH
case 10: //Prepare FILWIDTH
#if defined(FILWIDTH_PIN) && (FILWIDTH_PIN> -1)
#if FILWIDTH_PIN>7
ADCSRB = 1<<MUX5;
@ -1628,9 +1779,9 @@ ISR(TIMER0_COMPB_vect)
ADCSRA |= 1<<ADSC; // Start conversion
#endif
lcd_buttons_update();
temp_state = 9;
temp_state = 11;
break;
case 9: //Measure FILWIDTH
case 11: //Measure FILWIDTH
#if defined(FILWIDTH_PIN) &&(FILWIDTH_PIN > -1)
//raw_filwidth_value += ADC; //remove to use an IIR filter approach
if(ADC>102) //check that ADC is reading a voltage > 0.5 volts, otherwise don't take in the data.
@ -1646,7 +1797,7 @@ ISR(TIMER0_COMPB_vect)
break;
case 10: //Startup, delay initial temp reading a tiny bit so the hardware can settle.
case 12: //Startup, delay initial temp reading a tiny bit so the hardware can settle.
temp_state = 0;
break;
// default:
@ -1668,6 +1819,9 @@ ISR(TIMER0_COMPB_vect)
#endif
#if EXTRUDERS > 2
current_temperature_raw[2] = raw_temp_2_value;
#endif
#if EXTRUDERS > 3
current_temperature_raw[3] = raw_temp_3_value;
#endif
current_temperature_bed_raw = raw_temp_bed_value;
}
@ -1683,6 +1837,7 @@ ISR(TIMER0_COMPB_vect)
raw_temp_0_value = 0;
raw_temp_1_value = 0;
raw_temp_2_value = 0;
raw_temp_3_value = 0;
raw_temp_bed_value = 0;
#if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP
@ -1699,6 +1854,8 @@ ISR(TIMER0_COMPB_vect)
#endif
min_temp_error(0);
}
#if EXTRUDERS > 1
#if HEATER_1_RAW_LO_TEMP > HEATER_1_RAW_HI_TEMP
if(current_temperature_raw[1] <= maxttemp_raw[1]) {
@ -1731,6 +1888,23 @@ ISR(TIMER0_COMPB_vect)
min_temp_error(2);
}
#endif
#if EXTRUDERS > 3
#if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP
if(current_temperature_raw[3] <= maxttemp_raw[3]) {
#else
if(current_temperature_raw[3] >= maxttemp_raw[3]) {
#endif
max_temp_error(3);
}
#if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP
if(current_temperature_raw[3] >= minttemp_raw[3]) {
#else
if(current_temperature_raw[3] <= minttemp_raw[3]) {
#endif
min_temp_error(3);
}
#endif
/* No bed MINTEMP error? */
#if defined(BED_MAXTEMP) && (TEMP_SENSOR_BED != 0)
@ -1790,5 +1964,3 @@ float unscalePID_d(float d)
}
#endif //PIDTEMP

14
Marlin/temperature.h
Unescape View File

@ -159,6 +159,15 @@ FORCE_INLINE bool isCoolingBed() {
#define setTargetHotend2(_celsius) do{}while(0)
#endif
#if EXTRUDERS > 3
#define degHotend3() degHotend(3)
#define degTargetHotend3() degTargetHotend(3)
#define setTargetHotend3(_celsius) setTargetHotend((_celsius), 3)
#define isHeatingHotend3() isHeatingHotend(3)
#define isCoolingHotend3() isCoolingHotend(3)
#else
#define setTargetHotend3(_celsius) do{}while(0)
#endif
#if EXTRUDERS > 4
#error Invalid number of extruders
#endif
@ -171,8 +180,8 @@ void updatePID();
#if defined (THERMAL_RUNAWAY_PROTECTION_PERIOD) && THERMAL_RUNAWAY_PROTECTION_PERIOD > 0
void thermal_runaway_protection(int *state, unsigned long *timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc);
static int thermal_runaway_state_machine[3]; // = {0,0,0};
static unsigned long thermal_runaway_timer[3]; // = {0,0,0};
static int thermal_runaway_state_machine[4]; // = {0,0,0,0};
static unsigned long thermal_runaway_timer[4]; // = {0,0,0,0};
static bool thermal_runaway = false;
#if TEMP_SENSOR_BED != 0
static int thermal_runaway_bed_state_machine;
@ -197,4 +206,3 @@ void setExtruderAutoFanState(int pin, bool state);
void checkExtruderAutoFans();
#endif

69
Marlin/thermistortables.h
Unescape View File

@ -5,7 +5,7 @@
#define OVERSAMPLENR 16
#if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORHEATER_2 == 1) || (THERMISTORBED == 1) //100k bed thermistor
#if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORHEATER_2 == 1) || (THERMISTORHEATER_3 == 1) || (THERMISTORBED == 1) //100k bed thermistor
const short temptable_1[][2] PROGMEM = {
{ 23*OVERSAMPLENR , 300 },
@ -71,7 +71,7 @@ const short temptable_1[][2] PROGMEM = {
{ 1008*OVERSAMPLENR , 0 } //safety
};
#endif
#if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORBED == 2) //200k bed thermistor
#if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORHEATER_3 == 2) || (THERMISTORBED == 2) //200k bed thermistor
const short temptable_2[][2] PROGMEM = {
//200k ATC Semitec 204GT-2
//Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
@ -111,7 +111,7 @@ const short temptable_2[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORBED == 3) //mendel-parts
#if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORHEATER_3 == 3) || (THERMISTORBED == 3) //mendel-parts
const short temptable_3[][2] PROGMEM = {
{1*OVERSAMPLENR,864},
{21*OVERSAMPLENR,300},
@ -144,7 +144,7 @@ const short temptable_3[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORBED == 4) //10k thermistor
#if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORHEATER_3 == 4) || (THERMISTORBED == 4) //10k thermistor
const short temptable_4[][2] PROGMEM = {
{1*OVERSAMPLENR, 430},
{54*OVERSAMPLENR, 137},
@ -169,7 +169,7 @@ const short temptable_4[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORHEATER_2 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2)
#if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORHEATER_2 == 5) || (THERMISTORHEATER_3 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2)
const short temptable_5[][2] PROGMEM = {
// ATC Semitec 104GT-2 (Used in ParCan)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
@ -209,7 +209,7 @@ const short temptable_5[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORHEATER_2 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor
#if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORHEATER_2 == 6) || (THERMISTORHEATER_3 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor
const short temptable_6[][2] PROGMEM = {
{1*OVERSAMPLENR, 350},
{28*OVERSAMPLENR, 250}, //top rating 250C
@ -252,7 +252,7 @@ const short temptable_6[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01
#if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORHEATER_3 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01
const short temptable_7[][2] PROGMEM = {
{1*OVERSAMPLENR, 941},
{19*OVERSAMPLENR, 362},
@ -315,7 +315,7 @@ const short temptable_7[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 71) || (THERMISTORHEATER_1 == 71) || (THERMISTORHEATER_2 == 71) || (THERMISTORBED == 71) // 100k Honeywell 135-104LAF-J01
#if (THERMISTORHEATER_0 == 71) || (THERMISTORHEATER_1 == 71) || (THERMISTORHEATER_2 == 71) || (THERMISTORHEATER_3 == 71) || (THERMISTORBED == 71) // 100k Honeywell 135-104LAF-J01
// R0 = 100000 Ohm
// T0 = 25 °C
// Beta = 3974
@ -466,7 +466,7 @@ const short temptable_71[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 8) || (THERMISTORHEATER_1 == 8) || (THERMISTORHEATER_2 == 8) || (THERMISTORBED == 8)
#if (THERMISTORHEATER_0 == 8) || (THERMISTORHEATER_1 == 8) || (THERMISTORHEATER_2 == 8) || (THERMISTORHEATER_3 == 8) || (THERMISTORBED == 8)
// 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
const short temptable_8[][2] PROGMEM = {
{1*OVERSAMPLENR, 704},
@ -491,7 +491,7 @@ const short temptable_8[][2] PROGMEM = {
{1008*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 9) || (THERMISTORHEATER_1 == 9) || (THERMISTORHEATER_2 == 9) || (THERMISTORBED == 9)
#if (THERMISTORHEATER_0 == 9) || (THERMISTORHEATER_1 == 9) || (THERMISTORHEATER_2 == 9) || (THERMISTORHEATER_3 == 9) || (THERMISTORBED == 9)
// 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
const short temptable_9[][2] PROGMEM = {
{1*OVERSAMPLENR, 936},
@ -527,7 +527,7 @@ const short temptable_9[][2] PROGMEM = {
{1016*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 10) || (THERMISTORHEATER_1 == 10) || (THERMISTORHEATER_2 == 10) || (THERMISTORBED == 10)
#if (THERMISTORHEATER_0 == 10) || (THERMISTORHEATER_1 == 10) || (THERMISTORHEATER_2 == 10) || (THERMISTORHEATER_3 == 10) || (THERMISTORBED == 10)
// 100k RS thermistor 198-961 (4.7k pullup)
const short temptable_10[][2] PROGMEM = {
{1*OVERSAMPLENR, 929},
@ -564,7 +564,7 @@ const short temptable_10[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 11) || (THERMISTORHEATER_1 == 11) || (THERMISTORHEATER_2 == 11) || (THERMISTORBED == 11)
#if (THERMISTORHEATER_0 == 11) || (THERMISTORHEATER_1 == 11) || (THERMISTORHEATER_2 == 11) || (THERMISTORHEATER_3 == 11) || (THERMISTORBED == 11)
// QU-BD silicone bed QWG-104F-3950 thermistor
const short temptable_11[][2] PROGMEM = {
@ -621,7 +621,7 @@ const short temptable_11[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 13) || (THERMISTORHEATER_1 == 13) || (THERMISTORHEATER_2 == 13) || (THERMISTORBED == 13)
#if (THERMISTORHEATER_0 == 13) || (THERMISTORHEATER_1 == 13) || (THERMISTORHEATER_2 == 13) || (THERMISTORHEATER_3 == 13) || (THERMISTORBED == 13)
// Hisens thermistor B25/50 =3950 +/-1%
const short temptable_13[][2] PROGMEM = {
@ -705,6 +705,10 @@ This does not match the normal thermistor behaviour so we need to set the follow
# define HEATER_2_RAW_HI_TEMP 16383
# define HEATER_2_RAW_LO_TEMP 0
#endif
#if (THERMISTORHEATER_3 == 20)
# define HEATER_3_RAW_HI_TEMP 16383
# define HEATER_3_RAW_LO_TEMP 0
#endif
#if (THERMISTORBED == 20)
# define HEATER_BED_RAW_HI_TEMP 16383
# define HEATER_BED_RAW_LO_TEMP 0
@ -762,7 +766,7 @@ const short temptable_20[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 51) || (THERMISTORHEATER_1 == 51) || (THERMISTORHEATER_2 == 51) || (THERMISTORBED == 51)
#if (THERMISTORHEATER_0 == 51) || (THERMISTORHEATER_1 == 51) || (THERMISTORHEATER_2 == 51) || (THERMISTORHEATER_3 == 51) || (THERMISTORBED == 51)
// 100k EPCOS (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee.
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
@ -824,7 +828,7 @@ const short temptable_51[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 52) || (THERMISTORHEATER_1 == 52) || (THERMISTORHEATER_2 == 52) || (THERMISTORBED == 52)
#if (THERMISTORHEATER_0 == 52) || (THERMISTORHEATER_1 == 52) || (THERMISTORHEATER_2 == 52) || (THERMISTORHEATER_3 == 52) || (THERMISTORBED == 52)
// 200k ATC Semitec 204GT-2 (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
@ -865,7 +869,7 @@ const short temptable_52[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 55) || (THERMISTORHEATER_1 == 55) || (THERMISTORHEATER_2 == 55) || (THERMISTORBED == 55)
#if (THERMISTORHEATER_0 == 55) || (THERMISTORHEATER_1 == 55) || (THERMISTORHEATER_2 == 55) || (THERMISTORHEATER_3 == 55) || (THERMISTORBED == 55)
// 100k ATC Semitec 104GT-2 (Used on ParCan) (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
@ -906,7 +910,7 @@ const short temptable_55[][2] PROGMEM = {
};
#endif
#if (THERMISTORHEATER_0 == 60) || (THERMISTORHEATER_1 == 60) || (THERMISTORHEATER_2 == 60) || (THERMISTORBED == 60) // Maker's Tool Works Kapton Bed Thermister
#if (THERMISTORHEATER_0 == 60) || (THERMISTORHEATER_1 == 60) || (THERMISTORHEATER_2 == 60) || (THERMISTORHEATER_3 == 60) || (THERMISTORBED == 60) // Maker's Tool Works Kapton Bed Thermister
// ./createTemperatureLookup.py --r0=100000 --t0=25 --r1=0 --r2=4700 --beta=3950
// r0: 100000
// t0: 25
@ -1037,7 +1041,7 @@ const short temptable_12[][2] PROGMEM = {
#define PtAdVal(T,R0,Rup) (short)(1024/(Rup/PtRt(T,R0)+1))
#define PtLine(T,R0,Rup) { PtAdVal(T,R0,Rup)*OVERSAMPLENR, T },
#if (THERMISTORHEATER_0 == 110) || (THERMISTORHEATER_1 == 110) || (THERMISTORHEATER_2 == 110) || (THERMISTORBED == 110) // Pt100 with 1k0 pullup
#if (THERMISTORHEATER_0 == 110) || (THERMISTORHEATER_1 == 110) || (THERMISTORHEATER_2 == 110) || (THERMISTORHEATER_3 == 110) || (THERMISTORBED == 110) // Pt100 with 1k0 pullup
const short temptable_110[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,100,1000)
@ -1049,7 +1053,7 @@ const short temptable_110[][2] PROGMEM = {
PtLine(300,100,1000)
};
#endif
#if (THERMISTORHEATER_0 == 147) || (THERMISTORHEATER_1 == 147) || (THERMISTORHEATER_2 == 147) || (THERMISTORBED == 147) // Pt100 with 4k7 pullup
#if (THERMISTORHEATER_0 == 147) || (THERMISTORHEATER_1 == 147) || (THERMISTORHEATER_2 == 147) || (THERMISTORHEATER_3 == 147) || (THERMISTORBED == 147) // Pt100 with 4k7 pullup
const short temptable_147[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,100,4700)
@ -1061,7 +1065,7 @@ const short temptable_147[][2] PROGMEM = {
PtLine(300,100,4700)
};
#endif
#if (THERMISTORHEATER_0 == 1010) || (THERMISTORHEATER_1 == 1010) || (THERMISTORHEATER_2 == 1010) || (THERMISTORBED == 1010) // Pt1000 with 1k0 pullup
#if (THERMISTORHEATER_0 == 1010) || (THERMISTORHEATER_1 == 1010) || (THERMISTORHEATER_2 == 1010) || (THERMISTORHEATER_3 == 1010) || (THERMISTORBED == 1010) // Pt1000 with 1k0 pullup
const short temptable_1010[][2] PROGMEM = {
PtLine(0,1000,1000)
PtLine(25,1000,1000)
@ -1078,7 +1082,7 @@ const short temptable_1010[][2] PROGMEM = {
PtLine(300,1000,1000)
};
#endif
#if (THERMISTORHEATER_0 == 1047) || (THERMISTORHEATER_1 == 1047) || (THERMISTORHEATER_2 == 1047) || (THERMISTORBED == 1047) // Pt1000 with 4k7 pullup
#if (THERMISTORHEATER_0 == 1047) || (THERMISTORHEATER_1 == 1047) || (THERMISTORHEATER_2 == 1047) || (THERMISTORHEATER_3 == 1047) || (THERMISTORBED == 1047) // Pt1000 with 4k7 pullup
const short temptable_1047[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,1000,4700)
@ -1163,6 +1167,29 @@ const short temptable_1047[][2] PROGMEM = {
# endif
#endif
#ifdef THERMISTORHEATER_3
# define HEATER_3_TEMPTABLE TT_NAME(THERMISTORHEATER_3)
# define HEATER_3_TEMPTABLE_LEN (sizeof(HEATER_3_TEMPTABLE)/sizeof(*HEATER_3_TEMPTABLE))
#else
# ifdef HEATER_3_USES_THERMISTOR
# error No heater 3 thermistor table specified
# else // HEATER_3_USES_THERMISTOR
# define HEATER_3_TEMPTABLE NULL
# define HEATER_3_TEMPTABLE_LEN 0
# endif // HEATER_3_USES_THERMISTOR
#endif
//Set the high and low raw values for the heater, this indicates which raw value is a high or low temperature
#ifndef HEATER_3_RAW_HI_TEMP
# ifdef HEATER_3_USES_THERMISTOR //In case of a thermistor the highest temperature results in the lowest ADC value
# define HEATER_3_RAW_HI_TEMP 0
# define HEATER_3_RAW_LO_TEMP 16383
# else //In case of an thermocouple the highest temperature results in the highest ADC value
# define HEATER_3_RAW_HI_TEMP 16383
# define HEATER_3_RAW_LO_TEMP 0
# endif
#endif
#ifdef THERMISTORBED
# define BEDTEMPTABLE TT_NAME(THERMISTORBED)
# define BEDTEMPTABLE_LEN (sizeof(BEDTEMPTABLE)/sizeof(*BEDTEMPTABLE))

70
Marlin/ultralcd.cpp
Unescape View File

@ -431,6 +431,11 @@ static void lcd_tune_menu()
#if TEMP_SENSOR_2 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE2, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_3 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE3, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM_EDIT(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15);
#endif
@ -443,6 +448,10 @@ static void lcd_tune_menu()
#if TEMP_SENSOR_2 != 0
MENU_ITEM_EDIT(int3, MSG_FLOW2, &extruder_multiply[2], 10, 999);
#endif
#if TEMP_SENSOR_3 != 0
MENU_ITEM_EDIT(int3, MSG_FLOW3, &extruder_multiply[3], 10, 999);
#endif
#ifdef BABYSTEPPING
#ifdef BABYSTEP_XY
@ -515,23 +524,46 @@ void lcd_preheat_abs2()
}
#endif //3 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //more than one extruder present
void lcd_preheat_pla012()
#if TEMP_SENSOR_3 != 0 //4 extruder preheat
void lcd_preheat_pla3()
{
setTargetHotend3(plaPreheatHotendTemp);
setTargetBed(plaPreheatHPBTemp);
fanSpeed = plaPreheatFanSpeed;
lcd_return_to_status();
setWatch(); // heater sanity check timer
}
void lcd_preheat_abs3()
{
setTargetHotend3(absPreheatHotendTemp);
setTargetBed(absPreheatHPBTemp);
fanSpeed = absPreheatFanSpeed;
lcd_return_to_status();
setWatch(); // heater sanity check timer
}
#endif //4 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 //more than one extruder present
void lcd_preheat_pla0123()
{
setTargetHotend0(plaPreheatHotendTemp);
setTargetHotend1(plaPreheatHotendTemp);
setTargetHotend2(plaPreheatHotendTemp);
setTargetHotend3(plaPreheatHotendTemp);
setTargetBed(plaPreheatHPBTemp);
fanSpeed = plaPreheatFanSpeed;
lcd_return_to_status();
setWatch(); // heater sanity check timer
}
void lcd_preheat_abs012()
void lcd_preheat_abs0123()
{
setTargetHotend0(absPreheatHotendTemp);
setTargetHotend1(absPreheatHotendTemp);
setTargetHotend2(absPreheatHotendTemp);
setTargetHotend3(absPreheatHotendTemp);
setTargetBed(absPreheatHPBTemp);
fanSpeed = absPreheatFanSpeed;
lcd_return_to_status();
@ -566,9 +598,12 @@ static void lcd_preheat_pla_menu()
#if TEMP_SENSOR_2 != 0 //3 extruder preheat
MENU_ITEM(function, MSG_PREHEAT_PLA2, lcd_preheat_pla2);
#endif //3 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
MENU_ITEM(function, MSG_PREHEAT_PLA012, lcd_preheat_pla012);
#endif //2 extruder preheat
#if TEMP_SENSOR_3 != 0 //4 extruder preheat
MENU_ITEM(function, MSG_PREHEAT_PLA3, lcd_preheat_pla3);
#endif //4 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 //all extruder preheat
MENU_ITEM(function, MSG_PREHEAT_PLA0123, lcd_preheat_pla0123);
#endif //all extruder preheat
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_PLA_BEDONLY, lcd_preheat_pla_bedonly);
#endif
@ -586,9 +621,13 @@ static void lcd_preheat_abs_menu()
#if TEMP_SENSOR_2 != 0 //3 extruder preheat
MENU_ITEM(function, MSG_PREHEAT_ABS2, lcd_preheat_abs2);
#endif //3 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
MENU_ITEM(function, MSG_PREHEAT_ABS012, lcd_preheat_abs012);
#endif //2 extruder preheat
#if TEMP_SENSOR_3 != 0 //4 extruder preheat
MENU_ITEM(function, MSG_PREHEAT_ABS3, lcd_preheat_abs3);
#endif //4 extruder preheat
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 //all extruder preheat
MENU_ITEM(function, MSG_PREHEAT_ABS0123, lcd_preheat_abs0123);
#endif //all extruder preheat
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_ABS_BEDONLY, lcd_preheat_abs_bedonly);
#endif
@ -600,6 +639,7 @@ void lcd_cooldown()
setTargetHotend0(0);
setTargetHotend1(0);
setTargetHotend2(0);
setTargetHotend3(0);
setTargetBed(0);
fanSpeed = 0;
lcd_return_to_status();
@ -777,6 +817,9 @@ static void lcd_control_temperature_menu()
#if TEMP_SENSOR_2 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE2, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_3 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE3, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM_EDIT(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15);
#endif
@ -916,13 +959,15 @@ static void lcd_control_volumetric_menu()
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_1, &filament_size[1], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
#if EXTRUDERS > 2
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_2, &filament_size[2], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
#endif
#endif
#if EXTRUDERS > 3
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_3, &filament_size[3], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
}
END_MENU();
}
#ifdef DOGLCD
static void lcd_set_contrast()
{
@ -962,7 +1007,6 @@ static void lcd_control_retract_menu()
MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACT_RECOVERF, &retract_recover_feedrate, 1, 999);
END_MENU();
}
#endif //FWRETRACT
#if SDCARDDETECT == -1

Write Preview
Loading…
Cancel
Save