@ -40,7 +40,7 @@
bool lcd_clicked ( ) ;
void lcd_implementation_clear ( ) ;
void lcd_mesh_edit_setup ( float initial ) ;
void tilt_mesh_based_on_probed_grid ( const bool ) ;
void tilt_mesh_based_on_probed_grid ( const bool ) ;
float lcd_mesh_edit ( ) ;
void lcd_z_offset_edit_setup ( float ) ;
float lcd_z_offset_edit ( ) ;
@ -175,7 +175,7 @@
* area you are manually probing . Note that the command tries to start you in a corner
* of the bed where movement will be predictable . You can force the location to be used in
* the distance calculations by using the X and Y parameters . You may find it is helpful to
* print out a Mesh Map ( G29 O ) to understand where the mesh is invalidated and where
* print out a Mesh Map ( G29 O ) to understand where the mesh is invalidated and where
* the nozzle will need to move in order to complete the command . The C parameter is
* available on the Phase 2 command also and indicates the search for points to measure should
* be done based on the current location of the nozzle .
@ -393,11 +393,11 @@
SERIAL_PROTOCOLLNPGM ( " ERROR - grid size must be 2 or more " ) ;
return ;
}
if ( grid_size_G > GRID_MAX_POINTS_X | | grid_size_G > GRID_MAX_POINTS_Y ) {
if ( grid_size_G > GRID_MAX_POINTS_X | | grid_size_G > GRID_MAX_POINTS_Y ) {
SERIAL_PROTOCOLLNPGM ( " ERROR - grid size can NOT exceed GRID_MAX_POINTS_X nor GRID_MAX_POINTS_Y " ) ;
return ;
}
tilt_mesh_based_on_probed_grid ( code_seen ( ' O ' ) | | code_seen ( ' M ' ) ) ;
tilt_mesh_based_on_probed_grid ( code_seen ( ' O ' ) | | code_seen ( ' M ' ) ) ;
}
if ( code_seen ( ' P ' ) ) {
@ -419,14 +419,14 @@
//
// Invalidate Entire Mesh and Automatically Probe Mesh in areas that can be reached by the probe
//
if ( ! code_seen ( ' C ' ) ) {
if ( ! code_seen ( ' C ' ) ) {
ubl . invalidate ( ) ;
SERIAL_PROTOCOLLNPGM ( " Mesh invalidated. Probing mesh. \n " ) ;
}
if ( g29_verbose_level > 1 ) {
SERIAL_ ECHOPGM ( " Probing Mesh Points Closest to ( " ) ;
SERIAL_ ECHO( x_pos ) ;
SERIAL_ ECHO PAI R( " , " , y_pos ) ;
SERIAL_ PROTOCOLPAIR ( " Probing Mesh Points Closest to ( " , x_pos ) ;
SERIAL_ PROTOCOLCHAR( ' , ' ) ;
SERIAL_ PROTOCOL ( y_pos ) ;
SERIAL_PROTOCOLLNPGM ( " ) \n " ) ;
}
probe_entire_mesh ( x_pos + X_PROBE_OFFSET_FROM_EXTRUDER , y_pos + Y_PROBE_OFFSET_FROM_EXTRUDER ,
@ -440,16 +440,16 @@
SERIAL_PROTOCOLLNPGM ( " Manually probing unreachable mesh locations. \n " ) ;
do_blocking_move_to_z ( Z_CLEARANCE_BETWEEN_PROBES ) ;
if ( ! x_flag & & ! y_flag ) { // use a good default location for the path
x_pos = X_MIN_POS ;
y_pos = Y_MIN_POS ;
if ( X_PROBE_OFFSET_FROM_EXTRUDER > 0 ) // The flipped > and < operators on these two comparisons is
x_pos = X_MAX_POS ; // intentional. It should cause the probed points to follow a
if ( Y_PROBE_OFFSET_FROM_EXTRUDER < 0 ) // nice path on Cartesian printers. It may make sense to
y_pos = Y_MAX_POS ; // have Delta printers default to the center of the bed.
// The flipped > and < operators on these two comparisons is
// intentional. It should cause the probed points to follow a
// nice path on Cartesian printers. It may make sense to
// have Delta printers default to the center of the bed.
// For now, until that is decided, it can be forced with the X
// and Y parameters.
x_pos = X_PROBE_OFFSET_FROM_EXTRUDER > 0 ? X_MAX_POS : X_MIN_POS ;
y_pos = Y_PROBE_OFFSET_FROM_EXTRUDER < 0 ? Y_MAX_POS : Y_MIN_POS ;
}
} // For now, until that is decided, it can be forced with the X
// and Y parameters.
if ( code_seen ( ' C ' ) ) {
x_pos = current_position [ X_AXIS ] ;
y_pos = current_position [ Y_AXIS ] ;
@ -674,7 +674,7 @@
if ( ELAPSED ( millis ( ) , nxt ) ) {
SERIAL_PROTOCOLLNPGM ( " \n Z-Offset Adjustment Stopped. " ) ;
do_blocking_move_to_z ( Z_CLEARANCE_DEPLOY_PROBE ) ;
lcd_setstatuspgm ( " Z-Offset Stopped " ) ;
lcd_setstatuspgm ( PSTR ( " Z-Offset Stopped " ) ) ;
restore_ubl_active_state_and_leave ( ) ;
goto LEAVE ;
}
@ -693,7 +693,7 @@
# if ENABLED(ULTRA_LCD)
lcd_reset_alert_level ( ) ;
lcd_setstatuspgm ( " " ) ;
lcd_setstatuspgm ( PSTR ( " " ) ) ;
lcd_quick_feedback ( ) ;
# endif
@ -773,7 +773,7 @@
return ;
}
location = find_closest_mesh_point_of_type ( INVALID , lx , ly , 1 , NULL , do_furthest ) ; // the '1' says we want the location to be relative to the probe
location = find_closest_mesh_point_of_type ( INVALID , lx , ly , 1 , NULL , do_furthest ) ; // the '1' says we want the location to be relative to the probe
if ( location . x_index > = 0 & & location . y_index > = 0 ) {
const float rawx = ubl . mesh_index_to_xpos [ location . x_index ] ,
@ -891,7 +891,7 @@
SERIAL_PROTOCOLLNPGM ( " Place Shim Under Nozzle and Perform Measurement. " ) ;
do_blocking_move_to_z ( in_height ) ;
do_blocking_move_to_xy ( ( float ( X_MAX_POS ) - float ( X_MIN_POS ) ) / 2.0 , ( float ( Y_MAX_POS ) - float ( Y_MIN_POS ) ) / 2.0 ) ;
//, min( planner.max_feedrate_mm_s[X_AXIS], planner.max_feedrate_mm_s[Y_AXIS])/2.0);
//, min( planner.max_feedrate_mm_s[X_AXIS], planner.max_feedrate_mm_s[Y_AXIS])/2.0);
const float z1 = use_encoder_wheel_to_measure_point ( ) ;
do_blocking_move_to_z ( current_position [ Z_AXIS ] + SIZE_OF_LITTLE_RAISE ) ;
@ -997,7 +997,7 @@
bool g29_parameter_parsing ( ) {
# if ENABLED(ULTRA_LCD)
lcd_setstatuspgm ( " Doing G29 UBL! " ) ;
lcd_setstatuspgm ( PSTR ( " Doing G29 UBL! " ) ) ;
lcd_quick_feedback ( ) ;
# endif
@ -1118,7 +1118,7 @@
ubl_state_recursion_chk + + ;
if ( ubl_state_recursion_chk ! = 1 ) {
SERIAL_ECHOLNPGM ( " save_ubl_active_state_and_disabled() called multiple times in a row. " ) ;
lcd_setstatuspgm ( " save_UBL_active() error " ) ;
lcd_setstatuspgm ( PSTR ( " save_UBL_active() error " ) ) ;
lcd_quick_feedback ( ) ;
return ;
}
@ -1129,7 +1129,7 @@
void restore_ubl_active_state_and_leave ( ) {
if ( - - ubl_state_recursion_chk ) {
SERIAL_ECHOLNPGM ( " restore_ubl_active_state_and_leave() called too many times. " ) ;
lcd_setstatuspgm ( " restore_UBL_active() error " ) ;
lcd_setstatuspgm ( PSTR ( " restore_UBL_active() error " ) ) ;
lcd_quick_feedback ( ) ;
return ;
}
@ -1369,7 +1369,7 @@
memset ( not_done , 0xFF , sizeof ( not_done ) ) ;
# if ENABLED(ULTRA_LCD)
lcd_setstatuspgm ( " Fine Tuning Mesh " ) ;
lcd_setstatuspgm ( PSTR ( " Fine Tuning Mesh " ) ) ;
# endif
do_blocking_move_to_z ( Z_CLEARANCE_DEPLOY_PROBE ) ;
@ -1377,7 +1377,7 @@
do {
if ( do_ubl_mesh_map ) ubl . display_map ( map_type ) ;
location = find_closest_mesh_point_of_type ( SET_IN_BITMAP , lx , ly , 0 , not_done , false ) ; // The '0' says we want to use the nozzle's position
location = find_closest_mesh_point_of_type ( SET_IN_BITMAP , lx , ly , 0 , not_done , false ) ; // The '0' says we want to use the nozzle's position
// It doesn't matter if the probe can not reach this
// location. This is a manual edit of the Mesh Point.
if ( location . x_index < 0 & & location . y_index < 0 ) continue ; // abort if we can't find any more points.
@ -1428,7 +1428,7 @@
lcd_return_to_status ( ) ;
//SERIAL_PROTOCOLLNPGM("\nFine Tuning of Mesh Stopped.");
do_blocking_move_to_z ( Z_CLEARANCE_DEPLOY_PROBE ) ;
lcd_setstatuspgm ( " Mesh Editing Stopped " ) ;
lcd_setstatuspgm ( PSTR ( " Mesh Editing Stopped " ) ) ;
while ( ubl_lcd_clicked ( ) ) idle ( ) ;
@ -1456,42 +1456,41 @@
do_blocking_move_to_xy ( lx , ly ) ;
# if ENABLED(ULTRA_LCD)
lcd_setstatuspgm ( " Done Editing Mesh " ) ;
lcd_setstatuspgm ( PSTR ( " Done Editing Mesh " ) ) ;
# endif
SERIAL_ECHOLNPGM ( " Done Editing Mesh " ) ;
}
void tilt_mesh_based_on_probed_grid ( const bool do_ubl_mesh_map ) {
int8_t grid_G_index_to_xpos [ grid_size_G ] ; // UBL MESH X index to be probed
int8_t grid_G_index_to_ypos [ grid_size_G ] ; // UBL MESH Y index to be probed
int8_t i , j , k , xCount , yCount , G_X_index , G_Y_index ; // counter variables
void tilt_mesh_based_on_probed_grid ( const bool do_ubl_mesh_map ) {
int8_t grid_G_index_to_xpos [ grid_size_G ] , // UBL MESH X index to be probed
grid_G_index_to_ypos [ grid_size_G ] , // UBL MESH Y index to be probed
i , j , k , xCount , yCount , G_X_index , G_Y_index ; // counter variables
float z_values_G [ grid_size_G ] [ grid_size_G ] ;
struct * results ;
* results ;
for ( G_Y_index = 0 ; G_Y_index < grid_size_G ; G_Y_index + + )
for ( G_X_index = 0 ; G_X_index < grid_size_G ; G_X_index + + )
z_values_G [ G_X_index ] [ G_Y_index ] = NAN ;
uint8_t x_min = GRID_MAX_POINTS_X - 1 ;
uint8_t x_max = 0 ;
uint8_t y_min = GRID_MAX_POINTS_Y - 1 ;
uint8_t y_max = 0 ;
uint8_t x_min = GRID_MAX_POINTS_X - 1 ,
x_max = 0 ,
y_min = GRID_MAX_POINTS_Y - 1 ,
y_max = 0 ;
//find min & max probeable points in the mesh
for ( xCount = 0 ; xCount < GRID_MAX_POINTS_X ; xCount + + ) {
for ( yCount = 0 ; yCount < GRID_MAX_POINTS_Y ; yCount + + ) {
for ( xCount = 0 ; xCount < GRID_MAX_POINTS_X ; xCount + + ) {
for ( yCount = 0 ; yCount < GRID_MAX_POINTS_Y ; yCount + + ) {
if ( WITHIN ( ubl . mesh_index_to_xpos [ xCount ] , MIN_PROBE_X , MAX_PROBE_X ) & & WITHIN ( ubl . mesh_index_to_ypos [ yCount ] , MIN_PROBE_Y , MAX_PROBE_Y ) ) {
if ( x_min > xCount ) x_min = xCount ;
if ( x_max < xCount ) x_max = xCount ;
if ( y_min > yCount ) y_min = yCount ;
if ( y_max < yCount ) y_max = yCount ;
NOMORE ( x_min , xCount ) ;
NOLESS ( x_max , xCount ) ;
NOMORE ( y_min , yCount ) ;
NOLESS ( y_max , yCount ) ;
}
}
}
if ( ( x_max - x_min + 1 ) < ( grid_size_G ) | | ( y_max - y_min + 1 ) < ( grid_size_G ) ) {
if ( x_max - x_min + 1 < grid_size_G | | y_max - y_min + 1 < grid_size_G ) {
SERIAL_ECHOPAIR ( " ERROR - probeable UBL MESH smaller than grid - X points: " , x_max - x_min + 1 ) ;
SERIAL_ECHOPAIR ( " Y points: " , y_max - y_min + 1 ) ;
SERIAL_ECHOLNPAIR ( " grid: " , grid_size_G ) ;
@ -1500,16 +1499,16 @@
// populate X matrix
for ( G_X_index = 0 ; G_X_index < grid_size_G ; G_X_index + + ) {
grid_G_index_to_xpos [ G_X_index ] = x_min + G_X_index * ( x_max - x_min ) / ( grid_size_G - 1 ) ;
if ( G_X_index > 0 & & grid_G_index_to_xpos [ G_X_index - 1 ] = = grid_G_index_to_xpos [ G_X_index ] ) {
grid_G_index_to_xpos [ G_X_index ] = x_min + G_X_index * ( x_max - x_min ) / ( grid_size_G - 1 ) ;
if ( G_X_index > 0 & & grid_G_index_to_xpos [ G_X_index - 1 ] = = grid_G_index_to_xpos [ G_X_index ] ) {
grid_G_index_to_xpos [ G_X_index ] = grid_G_index_to_xpos [ G_X_index - 1 ] + 1 ;
}
}
// populate Y matrix
for ( G_Y_index = 0 ; G_Y_index < grid_size_G ; G_Y_index + + ) {
grid_G_index_to_ypos [ G_Y_index ] = y_min + G_Y_index * ( y_max - y_min ) / ( grid_size_G - 1 ) ;
if ( G_Y_index > 0 & & grid_G_index_to_ypos [ G_Y_index - 1 ] = = grid_G_index_to_ypos [ G_Y_index ] ) {
grid_G_index_to_ypos [ G_Y_index ] = y_min + G_Y_index * ( y_max - y_min ) / ( grid_size_G - 1 ) ;
if ( G_Y_index > 0 & & grid_G_index_to_ypos [ G_Y_index - 1 ] = = grid_G_index_to_ypos [ G_Y_index ] ) {
grid_G_index_to_ypos [ G_Y_index ] = grid_G_index_to_ypos [ G_Y_index - 1 ] + 1 ;
}
}
@ -1540,7 +1539,7 @@
int8_t inStart , inStop , inInc ;
SERIAL_ECHOPAIR ( " \n PR_OUTER_VAR: " , PR_OUTER_VAR ) ;
SERIAL_ECHOPAIR ( " \n PR_OUTER_VAR: " , PR_OUTER_VAR ) ;
if ( zig ) { // away from origin
inStart = 0 ;
@ -1557,82 +1556,75 @@ SERIAL_ECHOPAIR("\nPR_OUTER_VAR: ", PR_OUTER_VAR);
// Inner loop is Y with PROBE_Y_FIRST enabled
for ( PR_INNER_VAR = inStart ; PR_INNER_VAR ! = inStop ; PR_INNER_VAR + = inInc ) {
SERIAL_ECHOPAIR ( " \n PR_INNER_VAR: " , PR_INNER_VAR ) ;
//SERIAL_ECHOPAIR("\nPR_INNER_VAR: ", PR_INNER_VAR);
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 1 ) ;
//SERIAL_ECHOPAIR("\nCheckpoint: ", 1);
// end of G29 AUTO_BED_LEVELING_BILINEAR method/code
if ( ubl_lcd_clicked ( ) ) {
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 2 ) ;
//SERIAL_ECHOPAIR("\nCheckpoint: ", 2);
SERIAL_ECHOLNPGM ( " \n Grid only partially populated. \n " ) ;
lcd_quick_feedback ( ) ;
STOW_PROBE ( ) ;
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 3 ) ;
//SERIAL_ECHOPAIR("\nCheckpoint: ", 3);
while ( ubl_lcd_clicked ( ) ) idle ( ) ;
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 4 ) ;
ubl . has_control_of_lcd_panel = false ;
restore_ubl_active_state_and_leave ( ) ;
safe_delay ( 50 ) ; // Debounce the Encoder wheel
return ;
}
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 5 ) ;
//SERIAL_ECHOPAIR("\nCheckpoint: ", 4);
ubl . has_control_of_lcd_panel = false ;
restore_ubl_active_state_and_leave ( ) ;
safe_delay ( 50 ) ; // Debounce the Encoder wheel
return ;
}
//SERIAL_ECHOPAIR("\nCheckpoint: ", 5);
const float probeX = ubl . mesh_index_to_xpos [ grid_G_index_to_xpos [ xCount ] ] , //where we want the probe to be
probeY = ubl . mesh_index_to_ypos [ grid_G_index_to_ypos [ yCount ] ] ;
SERIAL_ECHOPAIR ( " \n Checkpoint: " , 6 ) ;
//SERIAL_ECHOPAIR("\nCheckpoint: ", 6);
const float measured_z = probe_pt ( LOGICAL_X_POSITION ( probeX ) , LOGICAL_Y_POSITION ( probeY ) , code_seen ( ' E ' ) , ( code_seen ( ' V ' ) & & code_has_value ( ) ) ? code_value_int ( ) : 0 ) ; // takes into account the offsets
const float measured_z = probe_pt ( LOGICAL_X_POSITION ( probeX ) , LOGICAL_Y_POSITION ( probeY ) , code_seen ( ' E ' ) , ( code_seen ( ' V ' ) & & code_has_value ( ) ) ? code_value_int ( ) : 0 ) ; // takes into account the offsets
SERIAL_ECHOPAIR ( " \n measured_z: " , measured_z ) ;
//SERIAL_ECHOPAIR("\nmeasured_z: ", measured_z);
z_values_G [ xCount ] [ yCount ] = measured_z ;
//SERIAL_ LNPGM("\nFine Tuning of Mesh Stopped.");
//SERIAL_ ECHO LNPGM("\nFine Tuning of Mesh Stopped.");
}
}
SERIAL_ECHO ( " \n Done probing... \n " ) ;
//SERIAL_ECHOLNPGM("\nDone probing...\n");
STOW_PROBE ( ) ;
restore_ubl_active_state_and_leave ( ) ;
// ?? ubl.has_control_of_lcd_panel = true;
//
// ?? ubl.has_control_of_lcd_panel = true;
// do_blocking_move_to_xy(ubl.mesh_index_to_xpos[grid_G_index_to_xpos[0]], ubl.mesh_index_to_ypos[grid_G_index_to_ypos[0]]);
// least squares code
double xxx9 [ ] = { 0 , 50 , 100 , 150 , 200 , 20 , 70 , 120 , 165 , 195 , 0 , 50 , 100 , 150 , 200 , 0 , 55 , 100 , 150 , 200 , 0 , 65 , 100 , 150 , 205 } ;
double yyy9 [ ] = { 0 , 1 , 2 , 3 , 4 , 50 , 51 , 52 , 53 , 54 , 100 , 101 , 102 , 103 , 104 , 150 , 151 , 152 , 153 , 154 , 200 , 201 , 202 , 203 , 204 } ;
double zzz9 [ ] = { 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .012 , 0.01 } ;
int nine_size = sizeof ( xxx9 ) / sizeof ( double ) ;
double xxx0 [ ] = { 0.0 , 0.0 , 1.0 } ; // Expect [0,0,0.1,0]
double yyy0 [ ] = { 0.0 , 1.0 , 0.0 } ;
double zzz0 [ ] = { 0.1 , 0.1 , 0.1 } ;
int zero_size = sizeof ( xxx0 ) / sizeof ( double ) ;
double xxx [ ] = { 0.0 , 0.0 , 1.0 , 1.0 } ; // Expect [0.1,0,0.05,0]
double yyy [ ] = { 0.0 , 1.0 , 0.0 , 1.0 } ;
double zzz [ ] = { 0.05 , 0.05 , 0.15 , 0.15 } ;
int three_size = sizeof ( xxx ) / sizeof ( double ) ;
results = lsf_linear_fit ( xxx9 , yyy9 , zzz9 , nine_size ) ;
SERIAL_ECHOPAIR ( " \n xxx9->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx9->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx9->D = " , results - > D ) ;
SERIAL_ECHO ( " \n " ) ;
results = lsf_linear_fit ( xxx0 , yyy0 , zzz0 , zero_size ) ;
SERIAL_ECHOPAIR ( " \n xxx0->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx0->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx0->D = " , results - > D ) ;
SERIAL_ECHO ( " \n " ) ;
results = lsf_linear_fit ( xxx , yyy , zzz , three_size ) ;
SERIAL_ECHOPAIR ( " \n xxx->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx->D = " , results - > D ) ;
SERIAL_ECHO ( " \n " ) ;
double xxx9 [ ] = { 0 , 50 , 100 , 150 , 200 , 20 , 70 , 120 , 165 , 195 , 0 , 50 , 100 , 150 , 200 , 0 , 55 , 100 , 150 , 200 , 0 , 65 , 100 , 150 , 205 } ,
yyy9 [ ] = { 0 , 1 , 2 , 3 , 4 , 50 , 51 , 52 , 53 , 54 , 100 , 101 , 102 , 103 , 104 , 150 , 151 , 152 , 153 , 154 , 200 , 201 , 202 , 203 , 204 } ,
zzz9 [ ] = { 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .02 , 0 , 0.01 , .002 , - .01 , - .012 , 0.01 } ,
xxx0 [ ] = { 0.0 , 0.0 , 1.0 } , // Expect [0,0,0.1,0]
yyy0 [ ] = { 0.0 , 1.0 , 0.0 } ,
zzz0 [ ] = { 0.1 , 0.1 , 0.1 } ,
xxx [ ] = { 0.0 , 0.0 , 1.0 , 1.0 } , // Expect [0.1,0,0.05,0]
yyy [ ] = { 0.0 , 1.0 , 0.0 , 1.0 } ,
zzz [ ] = { 0.05 , 0.05 , 0.15 , 0.15 } ;
results = lsf_linear_fit ( xxx9 , yyy9 , zzz9 , COUNT ( xxx9 ) ) ;
SERIAL_ECHOPAIR ( " \n xxx9->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx9->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx9->D = " , results - > D ) ;
SERIAL_EOL ;
results = lsf_linear_fit ( xxx0 , yyy0 , zzz0 , COUNT ( xxx0 ) ) ;
SERIAL_ECHOPAIR ( " \n xxx0->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx0->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx0->D = " , results - > D ) ;
SERIAL_EOL ;
results = lsf_linear_fit ( xxx , yyy , zzz , COUNT ( xxx ) ) ;
SERIAL_ECHOPAIR ( " \n xxx->A = " , results - > A ) ;
SERIAL_ECHOPAIR ( " \n xxx->B = " , results - > B ) ;
SERIAL_ECHOPAIR ( " \n xxx->D = " , results - > D ) ;
SERIAL_EOL ;
return ;
} // end of tilt_mesh_based_on_probed_grid()
# endif // AUTO_BED_LEVELING_UBL
Scott Lahteine
8 years ago
committed by