Merge pull request #3092 from thinkyhead/rc_2860_printrbot_lcd

Fix Printrboard with LCD (redo)

Marlin/Marlin_main.cpp

@@ -631,6 +631,13 @@ void servo_init() {
  *    • status LEDs
  */
 void setup() {
+
+  #ifdef DISABLE_JTAG
+    // Disable JTAG on AT90USB chips to free up pins for IO
+    MCUCR = 0x80;
+    MCUCR = 0x80;
+  #endif
+
   setup_killpin();
   setup_filrunoutpin();
   setup_powerhold();

Marlin/pins_PRINTRBOARD.h

@@ -15,6 +15,9 @@
 
 #define LARGE_FLASH        true
 
+// Disable JTAG pins so they can be used for the Extrudrboard
+#define DISABLE_JTAG       true
+
 #define X_STEP_PIN          0
 #define X_DIR_PIN           1
 #define X_ENABLE_PIN       39
@@ -64,7 +67,7 @@
 ////LCD Pin Setup////
 
 #define SDPOWER            -1
-#define SDSS                8
+#define SDSS               26
 #define LED_PIN            -1
 #define PS_ON_PIN          -1
 #define KILL_PIN           -1
@@ -79,15 +82,29 @@
 #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
   //we have no buzzer installed
   #define BEEPER_PIN -1
+
   //LCD Pins
   #if ENABLED(LCD_I2C_PANELOLU2)
     #define BTN_EN1 27  //RX1 - fastio.h pin mapping 27
     #define BTN_EN2 26  //TX1 - fastio.h pin mapping 26
     #define BTN_ENC 43 //A3 - fastio.h pin mapping 43
     #define SDSS   40 //use SD card on Panelolu2 (Teensyduino pin mapping)
+  #else
+    #define BTN_EN1 16
+    #define BTN_EN2 17
+    #define BTN_ENC 18//the click
   #endif // LCD_I2C_PANELOLU2
+
   //not connected to a pin
   #define SD_DETECT_PIN -1
+
+  #define LCD_PINS_RS 9
+  #define LCD_PINS_ENABLE 8
+  #define LCD_PINS_D4 7
+  #define LCD_PINS_D5 6
+  #define LCD_PINS_D6 5
+  #define LCD_PINS_D7 4
+
 #endif // ULTRA_LCD && NEWPANEL
 
 #if ENABLED(VIKI2) || ENABLED(miniVIKI)
@@ -104,7 +121,6 @@
 
   #define SDSS 45
   #define SD_DETECT_PIN -1 // FastIO (Manual says 72 I'm not certain cause I can't test)
-
   #if ENABLED(TEMP_STAT_LEDS)
     #define STAT_LED_RED      12 //Non-FastIO
     #define STAT_LED_BLUE     10 //Non-FastIO

Marlin/temperature.cpp

@@ -887,12 +887,14 @@ void tp_init() {
     SET_OUTPUT(HEATER_BED_PIN);
   #endif
   #if HAS_FAN
-    SET_OUTPUT(FAN_PIN);
-    #if ENABLED(FAST_PWM_FAN)
-      setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8
-    #endif
-    #if ENABLED(FAN_SOFT_PWM)
-      soft_pwm_fan = fanSpeedSoftPwm / 2;
+    #if ENABLED(FAST_PWM_FAN) || ENABLED(FAN_SOFT_PWM)
+      SET_OUTPUT(FAN_PIN);
+      #if ENABLED(FAST_PWM_FAN)
+        setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8
+      #endif
+      #if ENABLED(FAN_SOFT_PWM)
+        soft_pwm_fan = fanSpeedSoftPwm / 2;
+      #endif
     #endif
   #endif
 

Marlin/ultralcd.cpp

@@ -1584,7 +1584,7 @@ void lcd_init() {
   #endif//!NEWPANEL
 
   #if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
-    pinMode(SD_DETECT_PIN, INPUT);
+    SET_INPUT(SD_DETECT_PIN);
     WRITE(SD_DETECT_PIN, HIGH);
     lcd_sd_status = 2; // UNKNOWN
   #endif