forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Merge pull request #6346 from thinkyhead/rc_broken_abl_test

Browse Source 
Add support for SOLENOID_PROBE
master
Scott Lahteine 8 years ago committed by GitHub
parent 76765a8279 f4685c28b7
commit 2355d87e11
56 changed files with 421 additions and 151 deletions
Show Stats Download Patch File Download Diff File

18
.travis.yml
Unescape View File

@ -83,18 +83,23 @@ script:
- opt_set TEMP_SENSOR_1 1
- build_marlin
#
# Test 3 extruders on RUMBA (can use any board with >=3 extruders defined)
# Test 5 extruders on AZTEEG_X3_PRO (can use any board with >=5 extruders defined)
# Include a test for LIN_ADVANCE here also
#
- opt_set MOTHERBOARD BOARD_RUMBA
- opt_set EXTRUDERS 3
- opt_set TEMP_SENSOR_2 1
- opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
- opt_set EXTRUDERS 5
- opt_set TEMP_SENSOR_1 1
- opt_set TEMP_SENSOR_2 5
- opt_set TEMP_SENSOR_3 20
- opt_set TEMP_SENSOR_4 999
- opt_set TEMP_SENSOR_BED 1
- opt_enable_adv LIN_ADVANCE
- build_marlin
#
# Test PIDTEMPBED
#
- restore_configs
- opt_set TEMP_SENSOR_BED 1
- opt_enable PIDTEMPBED
- build_marlin
#
@ -158,11 +163,12 @@ script:
- opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT M100_FREE_MEMORY_WATCHER M100_FREE_MEMORY_DUMPER M100_FREE_MEMORY_CORRUPTOR INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT
- build_marlin
#
# Mixing Extruder
# Mixing Extruder with 5 steppers
#
- restore_configs
- opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
- opt_enable MIXING_EXTRUDER
- opt_set MIXING_STEPPERS 2
- opt_set MIXING_STEPPERS 5
- build_marlin
#
# Test DUAL_X_CARRIAGE

2
Marlin/Conditionals_LCD.h
Unescape View File

@ -374,7 +374,7 @@
/**
* Set a flag for any enabled probe
*/
#define PROBE_SELECTED (ENABLED(PROBE_MANUALLY) || ENABLED(FIX_MOUNTED_PROBE) || ENABLED(Z_PROBE_ALLEN_KEY) || HAS_Z_SERVO_ENDSTOP || ENABLED(Z_PROBE_SLED))
#define PROBE_SELECTED (ENABLED(PROBE_MANUALLY) || ENABLED(FIX_MOUNTED_PROBE) || ENABLED(Z_PROBE_ALLEN_KEY) || HAS_Z_SERVO_ENDSTOP || ENABLED(Z_PROBE_SLED) || ENABLED(SOLENOID_PROBE))
/**
* Clear probe pin settings when no probe is selected

155
Marlin/Conditionals_post.h
Unescape View File

@ -435,18 +435,100 @@
/**
* Shorthand for pin tests, used wherever needed
*/
// Steppers
#define HAS_X_ENABLE (PIN_EXISTS(X_ENABLE))
#define HAS_X_DIR (PIN_EXISTS(X_DIR))
#define HAS_X_STEP (PIN_EXISTS(X_STEP))
#define HAS_X_MICROSTEPS (PIN_EXISTS(X_MS1))
#define HAS_X2_ENABLE (PIN_EXISTS(X2_ENABLE))
#define HAS_X2_DIR (PIN_EXISTS(X2_DIR))
#define HAS_X2_STEP (PIN_EXISTS(X2_STEP))
#define HAS_Y_MICROSTEPS (PIN_EXISTS(Y_MS1))
#define HAS_Y_ENABLE (PIN_EXISTS(Y_ENABLE))
#define HAS_Y_DIR (PIN_EXISTS(Y_DIR))
#define HAS_Y_STEP (PIN_EXISTS(Y_STEP))
#define HAS_Z_MICROSTEPS (PIN_EXISTS(Z_MS1))
#define HAS_Y2_ENABLE (PIN_EXISTS(Y2_ENABLE))
#define HAS_Y2_DIR (PIN_EXISTS(Y2_DIR))
#define HAS_Y2_STEP (PIN_EXISTS(Y2_STEP))
#define HAS_Z_ENABLE (PIN_EXISTS(Z_ENABLE))
#define HAS_Z_DIR (PIN_EXISTS(Z_DIR))
#define HAS_Z_STEP (PIN_EXISTS(Z_STEP))
#define HAS_Z2_ENABLE (PIN_EXISTS(Z2_ENABLE))
#define HAS_Z2_DIR (PIN_EXISTS(Z2_DIR))
#define HAS_Z2_STEP (PIN_EXISTS(Z2_STEP))
// Extruder steppers and solenoids
#define HAS_E0_ENABLE (PIN_EXISTS(E0_ENABLE))
#define HAS_E0_DIR (PIN_EXISTS(E0_DIR))
#define HAS_E0_STEP (PIN_EXISTS(E0_STEP))
#define HAS_E0_MICROSTEPS (PIN_EXISTS(E0_MS1))
#define HAS_SOLENOID_0 (PIN_EXISTS(SOL0))
#define HAS_E1_ENABLE (PIN_EXISTS(E1_ENABLE))
#define HAS_E1_DIR (PIN_EXISTS(E1_DIR))
#define HAS_E1_STEP (PIN_EXISTS(E1_STEP))
#define HAS_E1_MICROSTEPS (PIN_EXISTS(E1_MS1))
#define HAS_SOLENOID_1 (PIN_EXISTS(SOL1))
#define HAS_E2_ENABLE (PIN_EXISTS(E2_ENABLE))
#define HAS_E2_DIR (PIN_EXISTS(E2_DIR))
#define HAS_E2_STEP (PIN_EXISTS(E2_STEP))
#define HAS_E2_MICROSTEPS (PIN_EXISTS(E2_MS1))
#define HAS_SOLENOID_2 (PIN_EXISTS(SOL2))
#define HAS_E3_ENABLE (PIN_EXISTS(E3_ENABLE))
#define HAS_E3_DIR (PIN_EXISTS(E3_DIR))
#define HAS_E3_STEP (PIN_EXISTS(E3_STEP))
#define HAS_E3_MICROSTEPS (PIN_EXISTS(E3_MS1))
#define HAS_SOLENOID_3 (PIN_EXISTS(SOL3))
#define HAS_E4_ENABLE (PIN_EXISTS(E4_ENABLE))
#define HAS_E4_DIR (PIN_EXISTS(E4_DIR))
#define HAS_E4_STEP (PIN_EXISTS(E4_STEP))
#define HAS_E4_MICROSTEPS (PIN_EXISTS(E4_MS1))
#define HAS_SOLENOID_4 (PIN_EXISTS(SOL4))
// Endstops and bed probe
#define HAS_X_MIN (PIN_EXISTS(X_MIN) && !IS_Z2_OR_PROBE(X_MIN_PIN))
#define HAS_X_MAX (PIN_EXISTS(X_MAX) && !IS_Z2_OR_PROBE(X_MAX_PIN))
#define HAS_Y_MIN (PIN_EXISTS(Y_MIN) && !IS_Z2_OR_PROBE(Y_MIN_PIN))
#define HAS_Y_MAX (PIN_EXISTS(Y_MAX) && !IS_Z2_OR_PROBE(Y_MAX_PIN))
#define HAS_Z_MIN (PIN_EXISTS(Z_MIN) && !IS_Z2_OR_PROBE(Z_MIN_PIN))
#define HAS_Z_MAX (PIN_EXISTS(Z_MAX) && !IS_Z2_OR_PROBE(Z_MAX_PIN))
#define HAS_Z2_MIN (PIN_EXISTS(Z2_MIN))
#define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
#define HAS_Z_MIN_PROBE_PIN (PIN_EXISTS(Z_MIN_PROBE))
// Thermistors
#define HAS_TEMP_0 (PIN_EXISTS(TEMP_0) && TEMP_SENSOR_0 != 0 && TEMP_SENSOR_0 > -2)
#define HAS_TEMP_1 (PIN_EXISTS(TEMP_1) && TEMP_SENSOR_1 != 0 && TEMP_SENSOR_1 > -2)
#define HAS_TEMP_2 (PIN_EXISTS(TEMP_2) && TEMP_SENSOR_2 != 0 && TEMP_SENSOR_2 > -2)
#define HAS_TEMP_3 (PIN_EXISTS(TEMP_3) && TEMP_SENSOR_3 != 0 && TEMP_SENSOR_3 > -2)
#define HAS_TEMP_4 (PIN_EXISTS(TEMP_4) && TEMP_SENSOR_4 != 0 && TEMP_SENSOR_4 > -2)
#define HAS_TEMP_HOTEND (HAS_TEMP_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED (PIN_EXISTS(TEMP_BED) && TEMP_SENSOR_BED != 0 && TEMP_SENSOR_BED > -2)
// Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
#define HAS_HEATER_1 (PIN_EXISTS(HEATER_1))
#define HAS_HEATER_2 (PIN_EXISTS(HEATER_2))
#define HAS_HEATER_3 (PIN_EXISTS(HEATER_3))
#define HAS_HEATER_4 (PIN_EXISTS(HEATER_4))
#define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED))
// Thermal protection
#define HAS_THERMALLY_PROTECTED_BED (ENABLED(THERMAL_PROTECTION_BED) && HAS_TEMP_BED && HAS_HEATER_BED)
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
// Auto fans
#define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN))
#define HAS_AUTO_FAN_1 (HOTENDS > 1 && PIN_EXISTS(E1_AUTO_FAN))
#define HAS_AUTO_FAN_2 (HOTENDS > 2 && PIN_EXISTS(E2_AUTO_FAN))
@ -463,87 +545,38 @@
#define AUTO_4_IS_1 (E4_AUTO_FAN_PIN == E1_AUTO_FAN_PIN)
#define AUTO_4_IS_2 (E4_AUTO_FAN_PIN == E2_AUTO_FAN_PIN)
#define AUTO_4_IS_3 (E4_AUTO_FAN_PIN == E3_AUTO_FAN_PIN)
// Other fans
#define HAS_FAN0 (PIN_EXISTS(FAN))
#define HAS_FAN1 (PIN_EXISTS(FAN1) && CONTROLLERFAN_PIN != FAN1_PIN && E0_AUTO_FAN_PIN != FAN1_PIN && E1_AUTO_FAN_PIN != FAN1_PIN && E2_AUTO_FAN_PIN != FAN1_PIN && E3_AUTO_FAN_PIN != FAN1_PIN)
#define HAS_FAN2 (PIN_EXISTS(FAN2) && CONTROLLERFAN_PIN != FAN2_PIN && E0_AUTO_FAN_PIN != FAN2_PIN && E1_AUTO_FAN_PIN != FAN2_PIN && E2_AUTO_FAN_PIN != FAN2_PIN && E3_AUTO_FAN_PIN != FAN2_PIN)
#define HAS_CONTROLLERFAN (PIN_EXISTS(CONTROLLERFAN))
// Servos
#define HAS_SERVOS (defined(NUM_SERVOS) && NUM_SERVOS > 0)
#define HAS_SERVO_0 (PIN_EXISTS(SERVO0))
#define HAS_SERVO_1 (PIN_EXISTS(SERVO1))
#define HAS_SERVO_2 (PIN_EXISTS(SERVO2))
#define HAS_SERVO_3 (PIN_EXISTS(SERVO3))
// Sensors
#define HAS_FILAMENT_WIDTH_SENSOR (PIN_EXISTS(FILWIDTH))
#define HAS_FIL_RUNOUT (PIN_EXISTS(FIL_RUNOUT))
// User Interface
#define HAS_HOME (PIN_EXISTS(HOME))
#define HAS_KILL (PIN_EXISTS(KILL))
#define HAS_SUICIDE (PIN_EXISTS(SUICIDE))
#define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH))
#define HAS_X_MIN (PIN_EXISTS(X_MIN) && !IS_Z2_OR_PROBE(X_MIN_PIN))
#define HAS_X_MAX (PIN_EXISTS(X_MAX) && !IS_Z2_OR_PROBE(X_MAX_PIN))
#define HAS_Y_MIN (PIN_EXISTS(Y_MIN) && !IS_Z2_OR_PROBE(Y_MIN_PIN))
#define HAS_Y_MAX (PIN_EXISTS(Y_MAX) && !IS_Z2_OR_PROBE(Y_MAX_PIN))
#define HAS_Z_MIN (PIN_EXISTS(Z_MIN) && !IS_Z2_OR_PROBE(Z_MIN_PIN))
#define HAS_Z_MAX (PIN_EXISTS(Z_MAX) && !IS_Z2_OR_PROBE(Z_MAX_PIN))
#define HAS_Z2_MIN (PIN_EXISTS(Z2_MIN))
#define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
#define HAS_Z_MIN_PROBE_PIN (PIN_EXISTS(Z_MIN_PROBE))
#define HAS_SOLENOID_1 (PIN_EXISTS(SOL1))
#define HAS_SOLENOID_2 (PIN_EXISTS(SOL2))
#define HAS_SOLENOID_3 (PIN_EXISTS(SOL3))
#define HAS_MICROSTEPS_X (PIN_EXISTS(X_MS1))
#define HAS_MICROSTEPS_Y (PIN_EXISTS(Y_MS1))
#define HAS_MICROSTEPS_Z (PIN_EXISTS(Z_MS1))
#define HAS_MICROSTEPS_E0 (PIN_EXISTS(E0_MS1))
#define HAS_MICROSTEPS_E1 (PIN_EXISTS(E1_MS1))
#define HAS_MICROSTEPS_E2 (PIN_EXISTS(E2_MS1))
#define HAS_MICROSTEPS (HAS_MICROSTEPS_X || HAS_MICROSTEPS_Y || HAS_MICROSTEPS_Z || HAS_MICROSTEPS_E0 || HAS_MICROSTEPS_E1 || HAS_MICROSTEPS_E2)
#define HAS_STEPPER_RESET (PIN_EXISTS(STEPPER_RESET))
#define HAS_X_ENABLE (PIN_EXISTS(X_ENABLE))
#define HAS_X2_ENABLE (PIN_EXISTS(X2_ENABLE))
#define HAS_Y_ENABLE (PIN_EXISTS(Y_ENABLE))
#define HAS_Y2_ENABLE (PIN_EXISTS(Y2_ENABLE))
#define HAS_Z_ENABLE (PIN_EXISTS(Z_ENABLE))
#define HAS_Z2_ENABLE (PIN_EXISTS(Z2_ENABLE))
#define HAS_E0_ENABLE (PIN_EXISTS(E0_ENABLE))
#define HAS_E1_ENABLE (PIN_EXISTS(E1_ENABLE))
#define HAS_E2_ENABLE (PIN_EXISTS(E2_ENABLE))
#define HAS_E3_ENABLE (PIN_EXISTS(E3_ENABLE))
#define HAS_E4_ENABLE (PIN_EXISTS(E4_ENABLE))
#define HAS_X_DIR (PIN_EXISTS(X_DIR))
#define HAS_X2_DIR (PIN_EXISTS(X2_DIR))
#define HAS_Y_DIR (PIN_EXISTS(Y_DIR))
#define HAS_Y2_DIR (PIN_EXISTS(Y2_DIR))
#define HAS_Z_DIR (PIN_EXISTS(Z_DIR))
#define HAS_Z2_DIR (PIN_EXISTS(Z2_DIR))
#define HAS_E0_DIR (PIN_EXISTS(E0_DIR))
#define HAS_E1_DIR (PIN_EXISTS(E1_DIR))
#define HAS_E2_DIR (PIN_EXISTS(E2_DIR))
#define HAS_E3_DIR (PIN_EXISTS(E3_DIR))
#define HAS_E4_DIR (PIN_EXISTS(E4_DIR))
#define HAS_X_STEP (PIN_EXISTS(X_STEP))
#define HAS_X2_STEP (PIN_EXISTS(X2_STEP))
#define HAS_Y_STEP (PIN_EXISTS(Y_STEP))
#define HAS_Y2_STEP (PIN_EXISTS(Y2_STEP))
#define HAS_Z_STEP (PIN_EXISTS(Z_STEP))
#define HAS_Z2_STEP (PIN_EXISTS(Z2_STEP))
#define HAS_E0_STEP (PIN_EXISTS(E0_STEP))
#define HAS_E1_STEP (PIN_EXISTS(E1_STEP))
#define HAS_E2_STEP (PIN_EXISTS(E2_STEP))
#define HAS_E3_STEP (PIN_EXISTS(E3_STEP))
#define HAS_E4_STEP (PIN_EXISTS(E4_STEP))
#define HAS_DIGIPOTSS (PIN_EXISTS(DIGIPOTSS))
#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER))
#define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT))
// Digital control
#define HAS_MICROSTEPS (HAS_X_MICROSTEPS || HAS_Y_MICROSTEPS || HAS_Z_MICROSTEPS || HAS_E0_MICROSTEPS || HAS_E1_MICROSTEPS || HAS_E2_MICROSTEPS || HAS_E3_MICROSTEPS || HAS_E4_MICROSTEPS)
#define HAS_STEPPER_RESET (PIN_EXISTS(STEPPER_RESET))
#define HAS_DIGIPOTSS (PIN_EXISTS(DIGIPOTSS))
#define HAS_MOTOR_CURRENT_PWM (PIN_EXISTS(MOTOR_CURRENT_PWM_XY) || PIN_EXISTS(MOTOR_CURRENT_PWM_Z) || PIN_EXISTS(MOTOR_CURRENT_PWM_E))
#define HAS_TEMP_HOTEND (HAS_TEMP_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_THERMALLY_PROTECTED_BED (HAS_TEMP_BED && HAS_HEATER_BED && ENABLED(THERMAL_PROTECTION_BED))
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
/**
* This setting is also used by M109 when trying to calculate
* a ballpark safe margin to prevent wait-forever situation.

3
Marlin/Configuration.h
Unescape View File

@ -593,6 +593,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

57
Marlin/Marlin_main.cpp
Unescape View File

@ -963,15 +963,15 @@ void servo_init() {
// This variant uses 3 separate pins for the RGB components.
// If the pins can do PWM then their intensity will be set.
digitalWrite(RGB_LED_R_PIN, r ? HIGH : LOW);
digitalWrite(RGB_LED_G_PIN, g ? HIGH : LOW);
digitalWrite(RGB_LED_B_PIN, b ? HIGH : LOW);
WRITE(RGB_LED_R_PIN, r ? HIGH : LOW);
WRITE(RGB_LED_G_PIN, g ? HIGH : LOW);
WRITE(RGB_LED_B_PIN, b ? HIGH : LOW);
analogWrite(RGB_LED_R_PIN, r);
analogWrite(RGB_LED_G_PIN, g);
analogWrite(RGB_LED_B_PIN, b);
#if ENABLED(RGBW_LED)
digitalWrite(RGB_LED_W_PIN, w ? HIGH : LOW);
WRITE(RGB_LED_W_PIN, w ? HIGH : LOW);
analogWrite(RGB_LED_W_PIN, w);
#endif
@ -1854,8 +1854,8 @@ static void clean_up_after_endstop_or_probe_move() {
// Dock sled a bit closer to ensure proper capturing
do_blocking_move_to_x(X_MAX_POS + SLED_DOCKING_OFFSET - ((stow) ? 1 : 0));
#if PIN_EXISTS(SLED)
digitalWrite(SLED_PIN, !stow); // switch solenoid
#if HAS_SOLENOID_1 && DISABLED(EXT_SOLENOID)
WRITE(SOL1_PIN, !stow); // switch solenoid
#endif
}
@ -2123,7 +2123,13 @@ static void clean_up_after_endstop_or_probe_move() {
// otherwise an Allen-Key probe can't be stowed.
#endif
#if ENABLED(Z_PROBE_SLED)
#if ENABLED(SOLENOID_PROBE)
#if HAS_SOLENOID_1
WRITE(SOL1_PIN, deploy);
#endif
#elif ENABLED(Z_PROBE_SLED)
dock_sled(!deploy);
@ -7588,26 +7594,31 @@ inline void gcode_M303() {
#if ENABLED(EXT_SOLENOID)
void enable_solenoid(uint8_t num) {
void enable_solenoid(const uint8_t num) {
switch (num) {
case 0:
OUT_WRITE(SOL0_PIN, HIGH);
break;
#if HAS_SOLENOID_1
#if HAS_SOLENOID_1 && EXTRUDERS > 1
case 1:
OUT_WRITE(SOL1_PIN, HIGH);
break;
#endif
#if HAS_SOLENOID_2
#if HAS_SOLENOID_2 && EXTRUDERS > 2
case 2:
OUT_WRITE(SOL2_PIN, HIGH);
break;
#endif
#if HAS_SOLENOID_3
#if HAS_SOLENOID_3 && EXTRUDERS > 3
case 3:
OUT_WRITE(SOL3_PIN, HIGH);
break;
#endif
#if HAS_SOLENOID_4 && EXTRUDERS > 4
case 4:
OUT_WRITE(SOL4_PIN, HIGH);
break;
#endif
default:
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(MSG_INVALID_SOLENOID);
@ -7619,9 +7630,18 @@ inline void gcode_M303() {
void disable_all_solenoids() {
OUT_WRITE(SOL0_PIN, LOW);
#if HAS_SOLENOID_1 && EXTRUDERS > 1
OUT_WRITE(SOL1_PIN, LOW);
#endif
#if HAS_SOLENOID_2 && EXTRUDERS > 2
OUT_WRITE(SOL2_PIN, LOW);
#endif
#if HAS_SOLENOID_3 && EXTRUDERS > 3
OUT_WRITE(SOL3_PIN, LOW);
#endif
#if HAS_SOLENOID_4 && EXTRUDERS > 4
OUT_WRITE(SOL4_PIN, LOW);
#endif
}
/**
@ -8548,7 +8568,7 @@ inline void gcode_M907() {
uint8_t case_light_brightness = 255;
void update_case_light() {
digitalWrite(CASE_LIGHT_PIN, case_light_on != INVERT_CASE_LIGHT ? HIGH : LOW);
WRITE(CASE_LIGHT_PIN, case_light_on != INVERT_CASE_LIGHT ? HIGH : LOW);
analogWrite(CASE_LIGHT_PIN, case_light_on != INVERT_CASE_LIGHT ? case_light_brightness : 0);
}
@ -10739,7 +10759,7 @@ void prepare_move_to_destination() {
uint8_t speed = (!lastMotorOn || ELAPSED(ms, lastMotorOn + (CONTROLLERFAN_SECS) * 1000UL)) ? 0 : CONTROLLERFAN_SPEED;
// allows digital or PWM fan output to be used (see M42 handling)
digitalWrite(CONTROLLERFAN_PIN, speed);
WRITE(CONTROLLERFAN_PIN, speed);
analogWrite(CONTROLLERFAN_PIN, speed);
}
}
@ -11437,9 +11457,9 @@ void setup() {
dac_init();
#endif
#if ENABLED(Z_PROBE_SLED) && PIN_EXISTS(SLED)
OUT_WRITE(SLED_PIN, LOW); // turn it off
#endif // Z_PROBE_SLED
#if (ENABLED(Z_PROBE_SLED) || ENABLED(SOLENOID_PROBE)) && HAS_SOLENOID_1
OUT_WRITE(SOL1_PIN, LOW); // turn it off
#endif
setup_homepin();
@ -11451,10 +11471,13 @@ void setup() {
OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // turn it off
#endif
#if ENABLED(RGB_LED)
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
SET_OUTPUT(RGB_LED_R_PIN);
SET_OUTPUT(RGB_LED_G_PIN);
SET_OUTPUT(RGB_LED_B_PIN);
#if ENABLED(RGBW_LED)
SET_OUTPUT(RGB_LED_W_PIN);
#endif
#endif
lcd_init();

16
Marlin/SanityCheck.h
Unescape View File

@ -172,6 +172,8 @@
#error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
#elif defined(min_software_endstops) || defined(max_software_endstops)
#error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration."
#elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN)
#error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
#endif
/**
@ -459,6 +461,9 @@ static_assert(1 >= 0
#if ENABLED(Z_PROBE_SLED)
+ 1
#endif
#if ENABLED(SOLENOID_PROBE)
+ 1
#endif
, "Please enable only one probe: PROBE_MANUALLY, FIX_MOUNTED_PROBE, Z Servo, BLTOUCH, Z_PROBE_ALLEN_KEY, or Z_PROBE_SLED."
);
@ -472,6 +477,17 @@ static_assert(1 >= 0
#error "You cannot use Z_PROBE_SLED with DELTA."
#endif
/**
* SOLENOID_PROBE requirements
*/
#if ENABLED(SOLENOID_PROBE)
#if ENABLED(EXT_SOLENOID)
#error "SOLENOID_PROBE is incompatible with EXT_SOLENOID."
#elif !HAS_SOLENOID_1
#error "SOLENOID_PROBE requires SOL1_PIN. It can be added to your Configuration.h."
#endif
#endif
/**
* NUM_SERVOS is required for a Z servo probe
*/

3
Marlin/example_configurations/Cartesio/Configuration.h
Unescape View File

@ -592,6 +592,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/Cartesio/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/Felix/Configuration.h
Unescape View File

@ -576,6 +576,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/Felix/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/Felix/DUAL/Configuration.h
Unescape View File

@ -576,6 +576,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

3
Marlin/example_configurations/Hephestos/Configuration.h
Unescape View File

@ -584,6 +584,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/Hephestos/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/Hephestos_2/Configuration.h
Unescape View File

@ -587,6 +587,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/Hephestos_2/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/K8200/Configuration.h
Unescape View File

@ -622,6 +622,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/K8200/Configuration_adv.h
Unescape View File

@ -342,6 +342,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/K8400/Configuration.h
Unescape View File

@ -593,6 +593,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/K8400/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/K8400/Dual-head/Configuration.h
Unescape View File

@ -593,6 +593,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

3
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
Unescape View File

@ -593,6 +593,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

3
Marlin/example_configurations/RigidBot/Configuration.h
Unescape View File

@ -592,6 +592,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/RigidBot/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/SCARA/Configuration.h
Unescape View File

@ -608,6 +608,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/SCARA/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/TAZ4/Configuration.h
Unescape View File

@ -613,6 +613,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/TAZ4/Configuration_adv.h
Unescape View File

@ -337,6 +337,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/TinyBoy2/Configuration.h
Unescape View File

@ -644,6 +644,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/TinyBoy2/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/WITBOX/Configuration.h
Unescape View File

@ -584,6 +584,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/WITBOX/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/adafruit/ST7565/Configuration.h
Unescape View File

@ -593,6 +593,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

3
Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h
Unescape View File

@ -662,6 +662,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/delta/generic/Configuration.h
Unescape View File

@ -649,6 +649,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/delta/generic/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/delta/kossel_mini/Configuration.h
Unescape View File

@ -642,6 +642,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/delta/kossel_pro/Configuration.h
Unescape View File

@ -643,6 +643,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
Unescape View File

@ -334,6 +334,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/delta/kossel_xl/Configuration.h
Unescape View File

@ -662,6 +662,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/makibox/Configuration.h
Unescape View File

@ -596,6 +596,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/makibox/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/tvrrug/Round2/Configuration.h
Unescape View File

@ -589,6 +589,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

3
Marlin/example_configurations/wt150/Configuration.h
Unescape View File

@ -598,6 +598,9 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

4
Marlin/example_configurations/wt150/Configuration_adv.h
Unescape View File

@ -329,6 +329,10 @@
#endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:

2
Marlin/pins_MEGATRONICS_3.h
Unescape View File

@ -61,8 +61,6 @@
#define Z_MIN_PROBE_PIN 19
#endif
#define SLED_PIN -1
//
// Steppers
//

4
Marlin/pins_RAMBO.h
Unescape View File

@ -63,10 +63,6 @@
#define Z_MIN_PROBE_PIN 30
#endif
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
//
// Limit Switches
//

2
Marlin/pins_RAMPS.h
Unescape View File

@ -85,8 +85,6 @@
#define Z_MIN_PROBE_PIN 32
#endif
#define SLED_PIN -1
//
// Steppers
//

7
Marlin/pins_SANGUINOLOLU_11.h
Unescape View File

@ -41,13 +41,6 @@
#define Y_STOP_PIN 19
#define Z_STOP_PIN 20
//
// Z Probe (when not Z_MIN_PIN)
//
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
//
// Steppers
//

2
Marlin/pins_SCOOVO_X9H.h
Unescape View File

@ -57,8 +57,6 @@
#define Z_MIN_PROBE_PIN 30
#endif
#define SLED_PIN -1
//
// Steppers
//

100
Marlin/stepper.cpp
Unescape View File

@ -1076,6 +1076,9 @@ void Stepper::init() {
#if HAS_E3_STEP
E_AXIS_INIT(3);
#endif
#if HAS_E4_STEP
E_AXIS_INIT(4);
#endif
// waveform generation = 0100 = CTC
CBI(TCCR1B, WGM13);
@ -1461,22 +1464,34 @@ void Stepper::report_positions() {
void Stepper::microstep_init() {
SET_OUTPUT(X_MS1_PIN);
SET_OUTPUT(X_MS2_PIN);
#if HAS_MICROSTEPS_Y
#if HAS_Y_MICROSTEPS
SET_OUTPUT(Y_MS1_PIN);
SET_OUTPUT(Y_MS2_PIN);
#endif
#if HAS_MICROSTEPS_Z
#if HAS_Z_MICROSTEPS
SET_OUTPUT(Z_MS1_PIN);
SET_OUTPUT(Z_MS2_PIN);
#endif
#if HAS_MICROSTEPS_E0
#if HAS_E0_MICROSTEPS
SET_OUTPUT(E0_MS1_PIN);
SET_OUTPUT(E0_MS2_PIN);
#endif
#if HAS_MICROSTEPS_E1
#if HAS_E1_MICROSTEPS
SET_OUTPUT(E1_MS1_PIN);
SET_OUTPUT(E1_MS2_PIN);
#endif
#if HAS_E2_MICROSTEPS
SET_OUTPUT(E2_MS1_PIN);
SET_OUTPUT(E2_MS2_PIN);
#endif
#if HAS_E3_MICROSTEPS
SET_OUTPUT(E3_MS1_PIN);
SET_OUTPUT(E3_MS2_PIN);
#endif
#if HAS_E4_MICROSTEPS
SET_OUTPUT(E4_MS1_PIN);
SET_OUTPUT(E4_MS2_PIN);
#endif
static const uint8_t microstep_modes[] = MICROSTEP_MODES;
for (uint16_t i = 0; i < COUNT(microstep_modes); i++)
microstep_mode(i, microstep_modes[i]);
@ -1484,33 +1499,51 @@ void Stepper::report_positions() {
void Stepper::microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2) {
if (ms1 >= 0) switch (driver) {
case 0: digitalWrite(X_MS1_PIN, ms1); break;
#if HAS_MICROSTEPS_Y
case 1: digitalWrite(Y_MS1_PIN, ms1); break;
case 0: WRITE(X_MS1_PIN, ms1); break;
#if HAS_Y_MICROSTEPS
case 1: WRITE(Y_MS1_PIN, ms1); break;
#endif
#if HAS_Z_MICROSTEPS
case 2: WRITE(Z_MS1_PIN, ms1); break;
#endif
#if HAS_E0_MICROSTEPS
case 3: WRITE(E0_MS1_PIN, ms1); break;
#endif
#if HAS_E1_MICROSTEPS
case 4: WRITE(E1_MS1_PIN, ms1); break;
#endif
#if HAS_MICROSTEPS_Z
case 2: digitalWrite(Z_MS1_PIN, ms1); break;
#if HAS_E2_MICROSTEPS
case 5: WRITE(E2_MS1_PIN, ms1); break;
#endif
#if HAS_MICROSTEPS_E0
case 3: digitalWrite(E0_MS1_PIN, ms1); break;
#if HAS_E3_MICROSTEPS
case 6: WRITE(E3_MS1_PIN, ms1); break;
#endif
#if HAS_MICROSTEPS_E1
case 4: digitalWrite(E1_MS1_PIN, ms1); break;
#if HAS_E4_MICROSTEPS
case 7: WRITE(E4_MS1_PIN, ms1); break;
#endif
}
if (ms2 >= 0) switch (driver) {
case 0: digitalWrite(X_MS2_PIN, ms2); break;
#if HAS_MICROSTEPS_Y
case 1: digitalWrite(Y_MS2_PIN, ms2); break;
case 0: WRITE(X_MS2_PIN, ms2); break;
#if HAS_Y_MICROSTEPS
case 1: WRITE(Y_MS2_PIN, ms2); break;
#endif
#if HAS_MICROSTEPS_Z
case 2: digitalWrite(Z_MS2_PIN, ms2); break;
#if HAS_Z_MICROSTEPS
case 2: WRITE(Z_MS2_PIN, ms2); break;
#endif
#if HAS_MICROSTEPS_E0
case 3: digitalWrite(E0_MS2_PIN, ms2); break;
#if HAS_E0_MICROSTEPS
case 3: WRITE(E0_MS2_PIN, ms2); break;
#endif
#if HAS_MICROSTEPS_E1
case 4: digitalWrite(E1_MS2_PIN, ms2); break;
#if HAS_E1_MICROSTEPS
case 4: WRITE(E1_MS2_PIN, ms2); break;
#endif
#if HAS_E2_MICROSTEPS
case 5: WRITE(E2_MS2_PIN, ms2); break;
#endif
#if HAS_E3_MICROSTEPS
case 6: WRITE(E3_MS2_PIN, ms2); break;
#endif
#if HAS_E4_MICROSTEPS
case 7: WRITE(E4_MS2_PIN, ms2); break;
#endif
}
}
@ -1530,26 +1563,41 @@ void Stepper::report_positions() {
SERIAL_PROTOCOLPGM("X: ");
SERIAL_PROTOCOL(READ(X_MS1_PIN));
SERIAL_PROTOCOLLN(READ(X_MS2_PIN));
#if HAS_MICROSTEPS_Y
#if HAS_Y_MICROSTEPS
SERIAL_PROTOCOLPGM("Y: ");
SERIAL_PROTOCOL(READ(Y_MS1_PIN));
SERIAL_PROTOCOLLN(READ(Y_MS2_PIN));
#endif
#if HAS_MICROSTEPS_Z
#if HAS_Z_MICROSTEPS
SERIAL_PROTOCOLPGM("Z: ");
SERIAL_PROTOCOL(READ(Z_MS1_PIN));
SERIAL_PROTOCOLLN(READ(Z_MS2_PIN));
#endif
#if HAS_MICROSTEPS_E0
#if HAS_E0_MICROSTEPS
SERIAL_PROTOCOLPGM("E0: ");
SERIAL_PROTOCOL(READ(E0_MS1_PIN));
SERIAL_PROTOCOLLN(READ(E0_MS2_PIN));
#endif
#if HAS_MICROSTEPS_E1
#if HAS_E1_MICROSTEPS
SERIAL_PROTOCOLPGM("E1: ");
SERIAL_PROTOCOL(READ(E1_MS1_PIN));
SERIAL_PROTOCOLLN(READ(E1_MS2_PIN));
#endif
#if HAS_E2_MICROSTEPS
SERIAL_PROTOCOLPGM("E2: ");
SERIAL_PROTOCOL(READ(E2_MS1_PIN));
SERIAL_PROTOCOLLN(READ(E2_MS2_PIN));
#endif
#if HAS_E3_MICROSTEPS
SERIAL_PROTOCOLPGM("E3: ");
SERIAL_PROTOCOL(READ(E3_MS1_PIN));
SERIAL_PROTOCOLLN(READ(E3_MS2_PIN));
#endif
#if HAS_E4_MICROSTEPS
SERIAL_PROTOCOLPGM("E4: ");
SERIAL_PROTOCOL(READ(E4_MS1_PIN));
SERIAL_PROTOCOLLN(READ(E4_MS2_PIN));
#endif
}
#endif // HAS_MICROSTEPS

9
Marlin/thermistortables.h
Unescape View File

@ -226,6 +226,15 @@
#define HEATER_3_RAW_LO_TEMP 0
#endif
#endif
#ifndef HEATER_4_RAW_HI_TEMP
#ifdef HEATER_4_USES_THERMISTOR
#define HEATER_4_RAW_HI_TEMP 0
#define HEATER_4_RAW_LO_TEMP 16383
#else
#define HEATER_4_RAW_HI_TEMP 16383
#define HEATER_4_RAW_LO_TEMP 0
#endif
#endif
#ifndef HEATER_BED_RAW_HI_TEMP
#ifdef BED_USES_THERMISTOR
#define HEATER_BED_RAW_HI_TEMP 0

Write Preview
Loading…
Cancel
Save