Patch servos code for move

- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`

Marlin/Conditionals.h

@@ -279,6 +279,8 @@
     #define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
   #endif
 
+  #define SERVO_LEVELING (defined(ENABLE_AUTO_BED_LEVELING) && defined(DEACTIVATE_SERVOS_AFTER_MOVE))
+
    /**
     * Sled Options
     */ 

Marlin/Marlin_main.cpp

@@ -36,8 +36,6 @@
   #endif
 #endif // ENABLE_AUTO_BED_LEVELING
 
-#define SERVO_LEVELING (defined(ENABLE_AUTO_BED_LEVELING) && defined(DEACTIVATE_SERVOS_AFTER_MOVE))
-
 #ifdef MESH_BED_LEVELING
   #include "mesh_bed_leveling.h"
 #endif

Marlin/servo.cpp

@@ -35,7 +35,7 @@
 
  write()     - Sets the servo angle in degrees.  (invalid angle that is valid as pulse in microseconds is treated as microseconds)
  writeMicroseconds() - Sets the servo pulse width in microseconds
- move(pin, angel) - Sequence of attach(pin), write(angel).
+ move(pin, angle) - Sequence of attach(pin), write(angle).
                     With DEACTIVATE_SERVOS_AFTER_MOVE it waits SERVO_DEACTIVATION_DELAY and detaches.
  read()      - Gets the last written servo pulse width as an angle between 0 and 180.
  readMicroseconds()   - Gets the last written servo pulse width in microseconds. (was read_us() in first release)
@@ -238,23 +238,26 @@ Servo::Servo() {
     this->servoIndex = INVALID_SERVO;  // too many servos
 }
 
-uint8_t Servo::attach(int pin) {
+int8_t Servo::attach(int pin) {
   return this->attach(pin, MIN_PULSE_WIDTH, MAX_PULSE_WIDTH);
 }
 
-uint8_t Servo::attach(int pin, int min, int max) {
-  if (this->servoIndex < MAX_SERVOS ) {
-    if(pin > 0)
-      servos[this->servoIndex].Pin.nbr = pin;
+int8_t Servo::attach(int pin, int min, int max) {
+
+  if (this->servoIndex >= MAX_SERVOS) return -1;
+
+  if (pin > 0) servos[this->servoIndex].Pin.nbr = pin;
   pinMode(servos[this->servoIndex].Pin.nbr, OUTPUT); // set servo pin to output
+
   // todo min/max check: abs(min - MIN_PULSE_WIDTH) /4 < 128
   this->min = (MIN_PULSE_WIDTH - min) / 4; //resolution of min/max is 4 uS
   this->max = (MAX_PULSE_WIDTH - max) / 4;
+
   // initialize the timer if it has not already been initialized
   timer16_Sequence_t timer = SERVO_INDEX_TO_TIMER(servoIndex);
   if (!isTimerActive(timer)) initISR(timer);
   servos[this->servoIndex].Pin.isActive = true;  // this must be set after the check for isTimerActive
-  }
+
   return this->servoIndex;
 }
 
@@ -301,12 +304,16 @@ int Servo::readMicroseconds() {
 
 bool Servo::attached() { return servos[this->servoIndex].Pin.isActive; }
 
-uint8_t Servo::move(int pin, int value) {
-  uint8_t ret;
+int8_t Servo::move(int pin, int value) {
+  int8_t ret;
+  #if SERVO_LEVELING
     ret = this->attach(pin);
-  if (ret) {
+  #else
+    ret = this->servoIndex;
+  #endif
+  if (ret >= 0) {
     this->write(value);
-    #ifdef DEACTIVATE_SERVOS_AFTER_MOVE && (SERVO_DEACTIVATION_DELAY > 0)
+    #if SERVO_LEVELING
       delay(SERVO_DEACTIVATION_DELAY);
       this->detach();
     #endif

Marlin/servo.h

@@ -117,12 +117,12 @@ typedef struct {
 class Servo {
   public:
     Servo();
-    uint8_t attach(int pin);           // attach the given pin to the next free channel, sets pinMode, returns channel number or 0 if failure
-    uint8_t attach(int pin, int min, int max); // as above but also sets min and max values for writes.
+    int8_t attach(int pin);           // attach the given pin to the next free channel, set pinMode, return channel number (-1 on fail)
+    int8_t attach(int pin, int min, int max); // as above but also sets min and max values for writes.
     void detach();
     void write(int value);             // if value is < 200 it is treated as an angle, otherwise as pulse width in microseconds
     void writeMicroseconds(int value); // Write pulse width in microseconds
-    uint8_t move(int pin, int value);  // attach the given pin to the next free channel, sets pinMode, returns channel number or 0 if failure.
+    int8_t move(int pin, int value);  // attach the given pin to the next free channel, set pinMode, return channel number (-1 if attach fails)
                                        // if value is < 200 it is treated as an angle, otherwise as pulse width in microseconds.
                                        // if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
     int read();                        // returns current pulse width as an angle between 0 and 180 degrees