Sanity checks for FILAMENT_CHANGE_FEATURE and FILAMENT_RUNOUT_SCRIPT

Marlin/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/SanityCheck.h

@@ -244,15 +244,21 @@
     #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
   #elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
     #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
+  #elif DISABLED(FILAMENT_CHANGE_FEATURE)
+    static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "FILAMENT_CHANGE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
   #endif
 #endif
 
 /**
  * Filament Change with Extruder Runout Prevention
  */
-#if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #if DISABLED(ULTIPANEL)
+    #error "FILAMENT_CHANGE_FEATURE currently requires an LCD controller."
+  #elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
     #error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
   #endif
+#endif
 
 /**
  * Individual axis homing is useless for DELTAS

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -642,9 +642,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -669,7 +675,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -661,9 +661,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -688,7 +694,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -661,9 +661,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -688,7 +694,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -666,9 +666,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -693,7 +699,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -661,9 +661,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -688,7 +694,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -659,9 +659,15 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
   #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
   #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
@@ -686,7 +692,6 @@
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
-#endif
 
 /******************************************************************************\
  * enable this section if you have TMC26X motor drivers.