Merge Complete M200 output with M503 (PR#2506)

master
Richard Wackerbarth 9 years ago
commit 47ae96ce15

@ -3082,7 +3082,7 @@ inline void gcode_M42() {
if (code_seen('P') && pin_status >= 0 && pin_status <= 255) if (code_seen('P') && pin_status >= 0 && pin_status <= 255)
pin_number = code_value_short(); pin_number = code_value_short();
for (int8_t i = 0; i < COUNT(sensitive_pins); i++) { for (uint8_t i = 0; i < COUNT(sensitive_pins); i++) {
if (sensitive_pins[i] == pin_number) { if (sensitive_pins[i] == pin_number) {
pin_number = -1; pin_number = -1;
break; break;
@ -4222,7 +4222,7 @@ inline void gcode_M226() {
if (pin_state >= -1 && pin_state <= 1) { if (pin_state >= -1 && pin_state <= 1) {
for (int8_t i = 0; i < COUNT(sensitive_pins); i++) { for (uint8_t i = 0; i < COUNT(sensitive_pins); i++) {
if (sensitive_pins[i] == pin_number) { if (sensitive_pins[i] == pin_number) {
pin_number = -1; pin_number = -1;
break; break;

@ -565,16 +565,8 @@ void Config_ResetDefault() {
#endif #endif
volumetric_enabled = false; volumetric_enabled = false;
filament_size[0] = DEFAULT_NOMINAL_FILAMENT_DIA; for (int q=0; q<COUNT(filament_size); q++)
#if EXTRUDERS > 1 filament_size[q] = DEFAULT_NOMINAL_FILAMENT_DIA;
filament_size[1] = DEFAULT_NOMINAL_FILAMENT_DIA;
#if EXTRUDERS > 2
filament_size[2] = DEFAULT_NOMINAL_FILAMENT_DIA;
#if EXTRUDERS > 3
filament_size[3] = DEFAULT_NOMINAL_FILAMENT_DIA;
#endif
#endif
#endif
calculate_volumetric_multipliers(); calculate_volumetric_multipliers();
SERIAL_ECHO_START; SERIAL_ECHO_START;
@ -826,16 +818,21 @@ void Config_PrintSettings(bool forReplay) {
#endif // FWRETRACT #endif // FWRETRACT
if (volumetric_enabled) { /**
* Volumetric extrusion M200
*/
if (!forReplay) { if (!forReplay) {
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Filament settings:"); SERIAL_ECHOPGM("Filament settings:");
if (volumetric_enabled)
SERIAL_EOL;
else
SERIAL_ECHOLNPGM(" Disabled");
} }
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 D", filament_size[0]); SERIAL_ECHOPAIR(" M200 D", filament_size[0]);
SERIAL_EOL; SERIAL_EOL;
#if EXTRUDERS > 1 #if EXTRUDERS > 1
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]); SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]);
@ -852,13 +849,14 @@ void Config_PrintSettings(bool forReplay) {
#endif #endif
#endif #endif
} else { if (!volumetric_enabled) {
if (!forReplay) {
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Filament settings: Disabled"); SERIAL_ECHOLNPGM(" M200 D0");
}
} }
/**
* Auto Bed Leveling
*/
#ifdef ENABLE_AUTO_BED_LEVELING #ifdef ENABLE_AUTO_BED_LEVELING
#ifdef CUSTOM_M_CODES #ifdef CUSTOM_M_CODES
if (!forReplay) { if (!forReplay) {

Loading…
Cancel
Save