forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Miscellaneous cleanup

Browse Source
master
Scott Lahteine 7 years ago
parent 9cf5b96971
commit 4e19c59ab3
4 changed files with 50 additions and 86 deletions
Show Stats Download Patch File Download Diff File

47
Marlin/Marlin_main.cpp
Unescape View File

@ -8942,8 +8942,8 @@ inline void gcode_M205() {
set_home_offset((AxisEnum)i, parser.value_linear_units());
#if ENABLED(MORGAN_SCARA)
if (parser.seen('T')) set_home_offset(A_AXIS, parser.value_linear_units()); // Theta
if (parser.seen('P')) set_home_offset(B_AXIS, parser.value_linear_units()); // Psi
if (parser.seen('T')) set_home_offset(A_AXIS, parser.value_float()); // Theta
if (parser.seen('P')) set_home_offset(B_AXIS, parser.value_float()); // Psi
#endif
report_current_position();
@ -9319,14 +9319,14 @@ inline void gcode_M226() {
#if ENABLED(BABYSTEP_XY)
for (uint8_t a = X_AXIS; a <= Z_AXIS; a++)
if (parser.seenval(axis_codes[a]) || (a == Z_AXIS && parser.seenval('S'))) {
const float offs = constrain(parser.value_axis_units(a), -2, 2);
const float offs = constrain(parser.value_axis_units((AxisEnum)a), -2, 2);
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
if (a == Z_AXIS) {
zprobe_zoffset += offs;
refresh_zprobe_zoffset(true); // 'true' to not babystep
}
#endif
thermalManager.babystep_axis(a, offs * planner.axis_steps_per_mm[a]);
thermalManager.babystep_axis((AxisEnum)a, offs * planner.axis_steps_per_mm[a]);
}
#else
if (parser.seenval('Z') || parser.seenval('S')) {
@ -13318,48 +13318,27 @@ void prepare_move_to_destination() {
#if !AVR_AT90USB1286_FAMILY
case TIMER0A:
#endif
case TIMER0B:
//_SET_CS(0, val);
break;
case TIMER0B: //_SET_CS(0, val);
break;
#endif
#ifdef TCCR1A
case TIMER1A:
case TIMER1B:
//_SET_CS(1, val);
break;
case TIMER1A: case TIMER1B: //_SET_CS(1, val);
break;
#endif
#ifdef TCCR2
case TIMER2:
case TIMER2:
_SET_CS(2, val);
break;
case TIMER2: case TIMER2: _SET_CS(2, val); break;
#endif
#ifdef TCCR2A
case TIMER2A:
case TIMER2B:
_SET_CS(2, val);
break;
case TIMER2A: case TIMER2B: _SET_CS(2, val); break;
#endif
#ifdef TCCR3A
case TIMER3A:
case TIMER3B:
case TIMER3C:
_SET_CS(3, val);
break;
case TIMER3A: case TIMER3B: case TIMER3C: _SET_CS(3, val); break;
#endif
#ifdef TCCR4A
case TIMER4A:
case TIMER4B:
case TIMER4C:
_SET_CS(4, val);
break;
case TIMER4A: case TIMER4B: case TIMER4C: _SET_CS(4, val); break;
#endif
#ifdef TCCR5A
case TIMER5A:
case TIMER5B:
case TIMER5C:
_SET_CS(5, val);
break;
case TIMER5A: case TIMER5B: case TIMER5C: _SET_CS(5, val); break;
#endif
}
}

70
Marlin/Max7219_Debug_LEDs.cpp
Unescape View File

@ -63,54 +63,41 @@
static uint8_t LEDs[8] = { 0 };
#ifdef CPU_32_BIT
#define MS_DELAY() delayMicroseconds(5) // 32-bit processors need a delay to stabilize the signal
#else
#define MS_DELAY() NOOP
#endif
void Max7219_PutByte(uint8_t data) {
CRITICAL_SECTION_START
for (uint8_t i = 8; i--;) {
#ifdef CPU_32_BIT // The 32-bit processors are so fast, a small delay in the code is needed
delayMicroseconds(5); // to let the signal wires stabilize.
WRITE(MAX7219_CLK_PIN, LOW); // tick
delayMicroseconds(5);
WRITE(MAX7219_DIN_PIN, (data & 0x80) ? HIGH : LOW); // send 1 or 0 based on data bit
delayMicroseconds(5);
WRITE(MAX7219_CLK_PIN, HIGH); // tock
delayMicroseconds(5);
#else
WRITE(MAX7219_CLK_PIN, LOW); // tick
WRITE(MAX7219_DIN_PIN, (data & 0x80) ? HIGH : LOW); // send 1 or 0 based on data bit
WRITE(MAX7219_CLK_PIN, HIGH); // tock
#endif
MS_DELAY();
WRITE(MAX7219_CLK_PIN, LOW); // tick
MS_DELAY();
WRITE(MAX7219_DIN_PIN, (data & 0x80) ? HIGH : LOW); // send 1 or 0 based on data bit
MS_DELAY();
WRITE(MAX7219_CLK_PIN, HIGH); // tock
MS_DELAY();
data <<= 1;
}
CRITICAL_SECTION_END
}
void Max7219(const uint8_t reg, const uint8_t data) {
#ifdef CPU_32_BIT
delayMicroseconds(5);
#endif
MS_DELAY();
CRITICAL_SECTION_START
WRITE(MAX7219_LOAD_PIN, LOW); // begin
#ifdef CPU_32_BIT // The 32-bit processors are so fast, a small delay in the code is needed
delayMicroseconds(5); // to let the signal wires stabilize.
#endif
MS_DELAY();
Max7219_PutByte(reg); // specify register
#ifdef CPU_32_BIT
delayMicroseconds(5);
#endif
MS_DELAY();
Max7219_PutByte(data); // put data
#ifdef CPU_32_BIT
delayMicroseconds(5);
#endif
MS_DELAY();
WRITE(MAX7219_LOAD_PIN, LOW); // and tell the chip to load the data
#ifdef CPU_32_BIT
delayMicroseconds(5);
#endif
MS_DELAY();
WRITE(MAX7219_LOAD_PIN, HIGH);
CRITICAL_SECTION_END
#ifdef CPU_32_BIT
delayMicroseconds(5);
#endif
MS_DELAY();
}
void Max7219_LED_Set(const uint8_t row, const uint8_t col, const bool on) {
@ -329,23 +316,22 @@ void Max7219_idle_tasks() {
#if ENABLED(MAX7219_DEBUG_PRINTER_ALIVE)
static millis_t next_blink = 0;
if (ELAPSED(millis(), next_blink)) {
Max7219_LED_Toggle(7, 7);
next_blink = millis() + 750;
Max7219_LED_Toggle(7, 7);
next_blink = millis() + 750;
}
#endif
#ifdef MAX7219_DEBUG_STEPPER_HEAD
static int16_t last_head_cnt=0;
if (last_head_cnt != head) {
if ( last_head_cnt < 8)
if (last_head_cnt < 8)
Max7219_LED_Off( last_head_cnt, MAX7219_DEBUG_STEPPER_HEAD);
else
Max7219_LED_Off( last_head_cnt-8, MAX7219_DEBUG_STEPPER_HEAD+1);
last_head_cnt = head;
if ( head < 8)
if (head < 8)
Max7219_LED_On(head, MAX7219_DEBUG_STEPPER_HEAD);
else
Max7219_LED_On(head-8, MAX7219_DEBUG_STEPPER_HEAD+1);
@ -355,13 +341,13 @@ void Max7219_idle_tasks() {
#ifdef MAX7219_DEBUG_STEPPER_TAIL
static int16_t last_tail_cnt=0;
if (last_tail_cnt != tail) {
if ( last_tail_cnt < 8)
if (last_tail_cnt < 8)
Max7219_LED_Off( last_tail_cnt, MAX7219_DEBUG_STEPPER_TAIL);
else
Max7219_LED_Off( last_tail_cnt-8, MAX7219_DEBUG_STEPPER_TAIL+1);
last_tail_cnt = tail;
if ( tail < 8)
if (tail < 8)
Max7219_LED_On(tail, MAX7219_DEBUG_STEPPER_TAIL);
else
Max7219_LED_On(tail-8, MAX7219_DEBUG_STEPPER_TAIL+1);
@ -381,10 +367,10 @@ void Max7219_idle_tasks() {
en = max(current_depth, last_depth);
if (current_depth < last_depth)
for (uint8_t i = st; i <= en; i++) // clear the highest order LEDs
Max7219_LED_Off(i/2, MAX7219_DEBUG_STEPPER_QUEUE + (i & 1));
Max7219_LED_Off(i/2, MAX7219_DEBUG_STEPPER_QUEUE + (i & 1));
else
for (uint8_t i = st; i <= en; i++) // set the LEDs to current depth
Max7219_LED_On(i/2, MAX7219_DEBUG_STEPPER_QUEUE + (i & 1));
for (uint8_t i = st; i <= en; i++) // set the LEDs to current depth
Max7219_LED_On(i/2, MAX7219_DEBUG_STEPPER_QUEUE + (i & 1));
last_depth = current_depth;
}

4
Marlin/configuration_store.cpp
Unescape View File

@ -215,8 +215,8 @@ MarlinSettings settings;
#endif
/**
* Post-process after Retrieve or Reset
*/
* Post-process after Retrieve or Reset
*/
void MarlinSettings::postprocess() {
// steps per s2 needs to be updated to agree with units per s2
planner.reset_acceleration_rates();

3
Marlin/planner.cpp
Unescape View File

@ -528,8 +528,7 @@ void Planner::check_axes_activity() {
}
inline float calculate_volumetric_multiplier(const float &diameter) {
if (!parser.volumetric_enabled || diameter == 0) return 1.0;
return 1.0 / CIRCLE_AREA(diameter * 0.5);
return (parser.volumetric_enabled && diameter) ? 1.0 / CIRCLE_AREA(diameter * 0.5) : 1.0;
}
void Planner::calculate_volumetric_multipliers() {

Write Preview
Loading…
Cancel
Save