XON/XOFF corrections, tweaks, formatting, etc.

master
Scott Lahteine 7 years ago
parent 94caabf89a
commit 4e19ff75b6

@ -107,7 +107,7 @@
* *
* 250000 works in most cases, but you might try a lower speed if * 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing. * you commonly experience drop-outs during host printing.
* You may try up to 1000000 to speed up file transfer to the SD card * You may try up to 1000000 to speed up SD file transfer.
* *
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
*/ */

@ -740,24 +740,27 @@
// :[0, 2, 4, 8, 16, 32, 64, 128, 256] // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
#define TX_BUFFER_SIZE 0 #define TX_BUFFER_SIZE 0
// Reception from Host Buffer Size // Host Receive Buffer Size
// This is the size of the Reception buffer. If XON/XOFF software flow control // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
// is not enabled, then 32 bytes should be enough. But if you plan to use XON/XOFF // To use flow control, set this buffer size to at least 1024 bytes.
// you need 1024 bytes at least.
// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
#define RX_BUFFER_SIZE 1024 //#define RX_BUFFER_SIZE 1024
// This setting determines if the printer will send the XON/XOFF #if RX_BUFFER_SIZE >= 1024
// control characters to the host to signal RX buffer is becoming full // Enable to have the controller send XON/XOFF control characters to
#define SERIAL_XON_XOFF 1 // the host to signal the RX buffer is becoming full.
//#define SERIAL_XON_XOFF
#endif
// This setting determines if you want to display and collect #if ENABLED(SDSUPPORT)
// maximum RX queue usage after transferring a file to the SD // Enable this option to collect and display the maximum
//#define SERIAL_STATS_MAX_RX_QUEUED 1 // RX queue usage after transferring a file to SD.
//#define SERIAL_STATS_MAX_RX_QUEUED
// This setting determines if you want to display and collect // Enable this option to collect and display the number
// the number of dropped bytes after a file transfer to the SD // of dropped bytes after a file transfer to SD.
#define SERIAL_STATS_DROPPED_RX 1 //#define SERIAL_STATS_DROPPED_RX
#endif
// Enable an emergency-command parser to intercept certain commands as they // Enable an emergency-command parser to intercept certain commands as they
// enter the serial receive buffer, so they cannot be blocked. // enter the serial receive buffer, so they cannot be blocked.

@ -27,15 +27,30 @@
* Modified 23 November 2006 by David A. Mellis * Modified 23 November 2006 by David A. Mellis
* Modified 28 September 2010 by Mark Sproul * Modified 28 September 2010 by Mark Sproul
* Modified 14 February 2016 by Andreas Hardtung (added tx buffer) * Modified 14 February 2016 by Andreas Hardtung (added tx buffer)
* Modified 01 October 2017 by Eduardo José Tagle (added XON/XOFF)
*/ */
#include "MarlinSerial.h"
#include "Marlin.h"
// Disable HardwareSerial.cpp to support chips without a UART (Attiny, etc.) // Disable HardwareSerial.cpp to support chips without a UART (Attiny, etc.)
#include "MarlinConfig.h"
#if !defined(USBCON) && (defined(UBRRH) || defined(UBRR0H) || defined(UBRR1H) || defined(UBRR2H) || defined(UBRR3H)) #if !defined(USBCON) && (defined(UBRRH) || defined(UBRR0H) || defined(UBRR1H) || defined(UBRR2H) || defined(UBRR3H))
#include "MarlinSerial.h"
#include "Marlin.h"
struct ring_buffer_r {
unsigned char buffer[RX_BUFFER_SIZE];
volatile ring_buffer_pos_t head, tail;
};
#if TX_BUFFER_SIZE > 0
struct ring_buffer_t {
unsigned char buffer[TX_BUFFER_SIZE];
volatile uint8_t head, tail;
};
#endif
#if UART_PRESENT(SERIAL_PORT) #if UART_PRESENT(SERIAL_PORT)
ring_buffer_r rx_buffer = { { 0 }, 0, 0 }; ring_buffer_r rx_buffer = { { 0 }, 0, 0 };
#if TX_BUFFER_SIZE > 0 #if TX_BUFFER_SIZE > 0
@ -45,15 +60,21 @@
#endif #endif
#if ENABLED(SERIAL_XON_XOFF) #if ENABLED(SERIAL_XON_XOFF)
uint8_t xon_xoff_state = XON_XOFF_CHAR_SENT | XON_CHAR; uint8_t xon_xoff_state = XON_XOFF_CHAR_SENT | XON_CHAR;
constexpr uint8_t XON_XOFF_CHAR_SENT = 0x80; // XON / XOFF Character was sent
constexpr uint8_t XON_XOFF_CHAR_MASK = 0x1F; // XON / XOFF character to send
// XON / XOFF character definitions
constexpr uint8_t XON_CHAR = 17;
constexpr uint8_t XOFF_CHAR = 19;
#endif #endif
#if ENABLED(SERIAL_STATS_DROPPED_RX) #if ENABLED(SERIAL_STATS_DROPPED_RX)
uint8_t rx_dropped_bytes = 0; uint8_t rx_dropped_bytes = 0;
#endif #endif
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
ring_buffer_pos_t rx_max_enqueued = 0; ring_buffer_pos_t rx_max_enqueued = 0;
#endif #endif
#if ENABLED(EMERGENCY_PARSER) #if ENABLED(EMERGENCY_PARSER)
@ -149,92 +170,76 @@
FORCE_INLINE void store_rxd_char() { FORCE_INLINE void store_rxd_char() {
const ring_buffer_pos_t h = rx_buffer.head, const ring_buffer_pos_t h = rx_buffer.head,
i = (ring_buffer_pos_t)(h + 1) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); i = (ring_buffer_pos_t)(h + 1) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
// if we should be storing the received character into the location // If the character is to be stored at the index just before the tail
// just before the tail (meaning that the head would advance to the // (such that the head would advance to the current tail), the buffer is
// current location of the tail), we're about to overflow the buffer // critical, so don't write the character or advance the head.
// and so we don't write the character or advance the head. if (i != rx_buffer.tail) {
if (i != rx_buffer.tail) {
rx_buffer.buffer[h] = M_UDRx; rx_buffer.buffer[h] = M_UDRx;
rx_buffer.head = i; rx_buffer.head = i;
}
else {
(void)M_UDRx;
#if ENABLED(SERIAL_STATS_DROPPED_RX)
if (!++rx_dropped_bytes) ++rx_dropped_bytes;
#endif
}
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
// calculate count of bytes stored into the RX buffer
ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
// Keep track of the maximum count of enqueued bytes
NOLESS(rx_max_enqueued, rx_count);
#endif
#if ENABLED(SERIAL_XON_XOFF)
// for high speed transfers, we can use XON/XOFF protocol to do
// software handshake and avoid overruns.
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XON_CHAR) {
// calculate count of bytes stored into the RX buffer
ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
// if we are above 12.5% of RX buffer capacity, send XOFF before
// we run out of RX buffer space .. We need 325 bytes @ 250kbits/s to
// let the host react and stop sending bytes. This translates to 13mS
// propagation time.
if (rx_count >= (RX_BUFFER_SIZE) / 8) {
// If TX interrupts are disabled and data register is empty,
// just write the byte to the data register and be done. This
// shortcut helps significantly improve the effective datarate
// at high (>500kbit/s) bitrates, where interrupt overhead
// becomes a slowdown.
if (!TEST(M_UCSRxB, M_UDRIEx) && TEST(M_UCSRxA, M_UDREx)) {
// Send an XOFF character
M_UDRx = XOFF_CHAR;
// clear the TXC bit -- "can be cleared by writing a one to its bit
// location". This makes sure flush() won't return until the bytes
// actually got written
SBI(M_UCSRxA, M_TXCx);
// And remember it was sent
xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
}
else {
// TX interrupts disabled, but buffer still not empty ... or
// TX interrupts enabled. Reenable TX ints and schedule XOFF
// character to be sent
#if TX_BUFFER_SIZE > 0
SBI(M_UCSRxB, M_UDRIEx);
xon_xoff_state = XOFF_CHAR;
#else
// We are not using TX interrupts, we will have to send this manually
while (!TEST(M_UCSRxA, M_UDREx)) {/* nada */}
M_UDRx = XOFF_CHAR;
// And remember we already sent it
xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
#endif
}
}
} }
else { #endif // SERIAL_XON_XOFF
(void)M_UDRx;
#if ENABLED(SERIAL_STATS_DROPPED_RX)
if (!++rx_dropped_bytes)
++rx_dropped_bytes;
#endif
}
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
{
// calculate count of bytes stored into the RX buffer
ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
// Keep track of the maximum count of enqueued bytes
if (rx_max_enqueued < rx_count)
rx_max_enqueued = rx_count;
}
#endif
#if ENABLED(SERIAL_XON_XOFF)
// for high speed transfers, we can use XON/XOFF protocol to do
// software handshake and avoid overruns.
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XON_CHAR) {
// calculate count of bytes stored into the RX buffer
ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
// if we are above 12.5% of RX buffer capacity, send XOFF before
// we run out of RX buffer space .. We need 325 bytes @ 250kbits/s to
// let the host react and stop sending bytes. This translates to 13mS
// propagation time.
if (rx_count >= (RX_BUFFER_SIZE/8)) {
// If TX interrupts are disabled and data register is empty,
// just write the byte to the data register and be done. This
// shortcut helps significantly improve the effective datarate
// at high (>500kbit/s) bitrates, where interrupt overhead
// becomes a slowdown.
if (!TEST(M_UCSRxB, M_UDRIEx) && TEST(M_UCSRxA, M_UDREx)) {
// Send an XOFF character
M_UDRx = XOFF_CHAR;
// clear the TXC bit -- "can be cleared by writing a one to its bit
// location". This makes sure flush() won't return until the bytes
// actually got written
SBI(M_UCSRxA, M_TXCx);
// And remember we already sent it
xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
} else {
// TX interrupts disabled, but buffer still not empty ... or
// TX interrupts enabled. Reenable TX ints and schedule XOFF
// character to be sent
#if TX_BUFFER_SIZE > 0
SBI(M_UCSRxB, M_UDRIEx);
xon_xoff_state = XOFF_CHAR;
#else
// We are not using TX interrupts, we will have to send this manually
while (!TEST(M_UCSRxA, M_UDREx))
;
M_UDRx = XOFF_CHAR;
// And remember we already sent it
xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
#endif
}
}
}
#endif
#if ENABLED(EMERGENCY_PARSER) #if ENABLED(EMERGENCY_PARSER)
emergency_parser(c); emergency_parser(c);
@ -247,52 +252,39 @@
// If interrupts are enabled, there must be more data in the output // If interrupts are enabled, there must be more data in the output
// buffer. // buffer.
#if ENABLED(SERIAL_XON_XOFF) #if ENABLED(SERIAL_XON_XOFF)
// Do a priority insertion of an XON/XOFF char, if needed.
// If we must do a priority insertion of an XON/XOFF char, const uint8_t state = xon_xoff_state;
// do it now if (!(state & XON_XOFF_CHAR_SENT)) {
uint8_t state = xon_xoff_state; M_UDRx = state & XON_XOFF_CHAR_MASK;
if (!(state & XON_XOFF_CHAR_SENT)) { xon_xoff_state = state | XON_XOFF_CHAR_SENT;
M_UDRx = state & XON_XOFF_CHAR_MASK; }
xon_xoff_state = state | XON_XOFF_CHAR_SENT; else
#endif
} else { { // Send the next byte
#endif const uint8_t t = tx_buffer.tail, c = tx_buffer.buffer[t];
tx_buffer.tail = (t + 1) & (TX_BUFFER_SIZE - 1);
// Send the next byte M_UDRx = c;
const uint8_t t = tx_buffer.tail, }
c = tx_buffer.buffer[t];
tx_buffer.tail = (t + 1) & (TX_BUFFER_SIZE - 1);
M_UDRx = c;
#if ENABLED(SERIAL_XON_XOFF)
}
#endif
// clear the TXC bit -- "can be cleared by writing a one to its bit // clear the TXC bit -- "can be cleared by writing a one to its bit
// location". This makes sure flush() won't return until the bytes // location". This makes sure flush() won't return until the bytes
// actually got written // actually got written
SBI(M_UCSRxA, M_TXCx); SBI(M_UCSRxA, M_TXCx);
if (tx_buffer.head == tx_buffer.tail) { // Disable interrupts if the buffer is empty
// Buffer empty, so disable interrupts if (tx_buffer.head == tx_buffer.tail)
CBI(M_UCSRxB, M_UDRIEx); CBI(M_UCSRxB, M_UDRIEx);
}
} }
#ifdef M_USARTx_UDRE_vect #ifdef M_USARTx_UDRE_vect
ISR(M_USARTx_UDRE_vect) { ISR(M_USARTx_UDRE_vect) { _tx_udr_empty_irq(); }
_tx_udr_empty_irq();
}
#endif #endif
#endif // TX_BUFFER_SIZE #endif // TX_BUFFER_SIZE
#ifdef M_USARTx_RX_vect #ifdef M_USARTx_RX_vect
ISR(M_USARTx_RX_vect) { ISR(M_USARTx_RX_vect) { store_rxd_char(); }
store_rxd_char();
}
#endif #endif
// Public Methods // Public Methods
@ -302,9 +294,9 @@
bool useU2X = true; bool useU2X = true;
#if F_CPU == 16000000UL && SERIAL_PORT == 0 #if F_CPU == 16000000UL && SERIAL_PORT == 0
// hard-coded exception for compatibility with the bootloader shipped // Hard-coded exception for compatibility with the bootloader shipped
// with the Duemilanove and previous boards and the firmware on the 8U2 // with the Duemilanove and previous boards, and the firmware on the
// on the Uno and Mega 2560. // 8U2 on the Uno and Mega 2560.
if (baud == 57600) useU2X = false; if (baud == 57600) useU2X = false;
#endif #endif
@ -339,9 +331,9 @@
void MarlinSerial::checkRx(void) { void MarlinSerial::checkRx(void) {
if (TEST(M_UCSRxA, M_RXCx)) { if (TEST(M_UCSRxA, M_RXCx)) {
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
store_rxd_char(); store_rxd_char();
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
} }
} }
@ -361,35 +353,21 @@
else { else {
v = rx_buffer.buffer[t]; v = rx_buffer.buffer[t];
rx_buffer.tail = (ring_buffer_pos_t)(t + 1) & (RX_BUFFER_SIZE - 1); rx_buffer.tail = (ring_buffer_pos_t)(t + 1) & (RX_BUFFER_SIZE - 1);
#if ENABLED(SERIAL_XON_XOFF) #if ENABLED(SERIAL_XON_XOFF)
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) {
// for high speed transfers, we can use XON/XOFF protocol to do // Get count of bytes in the RX buffer
// software handshake and avoid overruns. ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) { // When below 10% of RX buffer capacity, send XON before
// running out of RX buffer bytes
// calculate count of bytes stored into the RX buffer if (rx_count < (RX_BUFFER_SIZE) / 10) {
ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
CRITICAL_SECTION_END; // End critical section before returning!
// if we are below 10% of RX buffer capacity, send XON before writeNoHandshake(XON_CHAR);
// we run out of RX buffer bytes return v;
if (rx_count < (RX_BUFFER_SIZE/10)) { }
}
// Send an XON character #endif
xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
// End critical section
CRITICAL_SECTION_END;
// Transmit the XON character
writeNoHandshake(XON_CHAR);
// Done
return v;
}
}
#endif
} }
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
return v; return v;
@ -397,68 +375,53 @@
ring_buffer_pos_t MarlinSerial::available(void) { ring_buffer_pos_t MarlinSerial::available(void) {
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
const ring_buffer_pos_t h = rx_buffer.head, const ring_buffer_pos_t h = rx_buffer.head, t = rx_buffer.tail;
t = rx_buffer.tail;
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
return (ring_buffer_pos_t)(RX_BUFFER_SIZE + h - t) & (RX_BUFFER_SIZE - 1); return (ring_buffer_pos_t)(RX_BUFFER_SIZE + h - t) & (RX_BUFFER_SIZE - 1);
} }
void MarlinSerial::flush(void) { void MarlinSerial::flush(void) {
// RX // Don't change this order of operations. If the RX interrupt occurs between
// don't reverse this or there may be problems if the RX interrupt // reading rx_buffer_head and updating rx_buffer_tail, the previous rx_buffer_head
// occurs after reading the value of rx_buffer_head but before writing // may be written to rx_buffer_tail, making the buffer appear full rather than empty.
// the value to rx_buffer_tail; the previous value of rx_buffer_head
// may be written to rx_buffer_tail, making it appear as if the buffer
// were full, not empty.
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
rx_buffer.head = rx_buffer.tail; rx_buffer.head = rx_buffer.tail;
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
#if ENABLED(SERIAL_XON_XOFF) #if ENABLED(SERIAL_XON_XOFF)
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) {
// for high speed transfers, we can use XON/XOFF protocol to do xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
// software handshake and avoid overruns. writeNoHandshake(XON_CHAR);
if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) { }
#endif
// Send an XON character
xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
// Transmit the XON character
writeNoHandshake(XON_CHAR);
}
#endif
} }
#if TX_BUFFER_SIZE > 0 #if TX_BUFFER_SIZE > 0
uint8_t MarlinSerial::availableForWrite(void) { uint8_t MarlinSerial::availableForWrite(void) {
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
const uint8_t h = tx_buffer.head, const uint8_t h = tx_buffer.head, t = tx_buffer.tail;
t = tx_buffer.tail;
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
return (uint8_t)(TX_BUFFER_SIZE + h - t) & (TX_BUFFER_SIZE - 1); return (uint8_t)(TX_BUFFER_SIZE + h - t) & (TX_BUFFER_SIZE - 1);
} }
void MarlinSerial::write(const uint8_t c) { void MarlinSerial::write(const uint8_t c) {
#if ENABLED(SERIAL_XON_XOFF)
#if ENABLED(SERIAL_XON_XOFF) const uint8_t state = xon_xoff_state;
uint8_t state = xon_xoff_state; if (!(state & XON_XOFF_CHAR_SENT)) {
if (!(state & XON_XOFF_CHAR_SENT)) { // Send 2 chars: XON/XOFF, then a user-specified char
// 2 characters to send: The XON/XOFF character and the user writeNoHandshake(state & XON_XOFF_CHAR_MASK);
// specified char. xon_xoff_state = state | XON_XOFF_CHAR_SENT;
writeNoHandshake(state & XON_XOFF_CHAR_MASK); }
xon_xoff_state = state | XON_XOFF_CHAR_SENT; #endif
} writeNoHandshake(c);
#endif
writeNoHandshake(c);
} }
void MarlinSerial::writeNoHandshake(uint8_t c) { void MarlinSerial::writeNoHandshake(const uint8_t c) {
_written = true; _written = true;
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
bool emty = (tx_buffer.head == tx_buffer.tail); bool emty = (tx_buffer.head == tx_buffer.tail);
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
// If the buffer and the data register is empty, just write the byte // If the buffer and the data register is empty, just write the byte
// to the data register and be done. This shortcut helps // to the data register and be done. This shortcut helps
// significantly improve the effective datarate at high (> // significantly improve the effective datarate at high (>
@ -497,7 +460,6 @@
return; return;
} }
void MarlinSerial::flushTX(void) { void MarlinSerial::flushTX(void) {
// TX // TX
// If we have never written a byte, no need to flush. This special // If we have never written a byte, no need to flush. This special
@ -516,35 +478,32 @@
} }
// If we get here, nothing is queued anymore (DRIE is disabled) and // If we get here, nothing is queued anymore (DRIE is disabled) and
// the hardware finished tranmission (TXC is set). // the hardware finished tranmission (TXC is set).
} }
#else #else // TX_BUFFER_SIZE == 0
void MarlinSerial::write(uint8_t c) {
void MarlinSerial::write(const uint8_t c) {
#if ENABLED(SERIAL_XON_XOFF) #if ENABLED(SERIAL_XON_XOFF)
// If we must do a priority insertion of an XON/XOFF char, do it now // Do a priority insertion of an XON/XOFF char, if needed.
uint8_t state = xon_xoff_state; const uint8_t state = xon_xoff_state;
if (!(state & XON_XOFF_CHAR_SENT)) { if (!(state & XON_XOFF_CHAR_SENT)) {
writeNoHandshake(state & XON_XOFF_CHAR_MASK);
writeNoHandshake(state & XON_XOFF_CHAR_MASK); xon_xoff_state = state | XON_XOFF_CHAR_SENT;
xon_xoff_state = state | XON_XOFF_CHAR_SENT; }
} #endif
#endif writeNoHandshake(c);
writeNoHandshake(c);
} }
void MarlinSerial::writeNoHandshake(uint8_t c) { void MarlinSerial::writeNoHandshake(uint8_t c) {
while (!TEST(M_UCSRxA, M_UDREx)) while (!TEST(M_UCSRxA, M_UDREx)) {/* nada */}
;
M_UDRx = c; M_UDRx = c;
} }
#endif
// end NEW
/// imports from print.h #endif // TX_BUFFER_SIZE == 0
/**
* Imports from print.h
*/
void MarlinSerial::print(char c, int base) { void MarlinSerial::print(char c, int base) {
print((long)c, base); print((long)c, base);

@ -84,61 +84,32 @@
#ifndef RX_BUFFER_SIZE #ifndef RX_BUFFER_SIZE
#define RX_BUFFER_SIZE 128 #define RX_BUFFER_SIZE 128
#endif #endif
#if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
#error "XON/XOFF requires a 1024 or greater RX_BUFFER_SIZE for allowing reliable transfers without drops"
#endif
#ifndef TX_BUFFER_SIZE #ifndef TX_BUFFER_SIZE
#define TX_BUFFER_SIZE 32 #define TX_BUFFER_SIZE 32
#endif #endif
#if !IS_POWEROF2(RX_BUFFER_SIZE) || (RX_BUFFER_SIZE < 2)
#error "RX_BUFFER_SIZE has to be a power of 2 and >= 2"
#endif
#if TX_BUFFER_SIZE != 0 && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWEROF2(TX_BUFFER_SIZE))
#error "TX_BUFFER_SIZE has to be a power of 2 or 0"
#endif
#if RX_BUFFER_SIZE > 256
typedef uint16_t ring_buffer_pos_t;
#else
typedef uint8_t ring_buffer_pos_t;
#endif
struct ring_buffer_r {
unsigned char buffer[RX_BUFFER_SIZE];
volatile ring_buffer_pos_t head;
volatile ring_buffer_pos_t tail;
};
#if TX_BUFFER_SIZE > 0 #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
struct ring_buffer_t { #error "XON/XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops."
unsigned char buffer[TX_BUFFER_SIZE];
volatile uint8_t head;
volatile uint8_t tail;
};
#endif #endif
#if !IS_POWER_OF_2(RX_BUFFER_SIZE) || RX_BUFFER_SIZE < 2
#if UART_PRESENT(SERIAL_PORT) #error "RX_BUFFER_SIZE must be a power of 2 greater than 1."
extern ring_buffer_r rx_buffer; #endif
#if TX_BUFFER_SIZE > 0 #if TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE))
extern ring_buffer_t tx_buffer; #error "TX_BUFFER_SIZE must be 0 or a power of 2 greater than 1."
#endif
#endif #endif
#if ENABLED(SERIAL_XON_XOFF) #if RX_BUFFER_SIZE > 256
#define XON_XOFF_CHAR_SENT (uint8_t)0x80 /* XON / XOFF Character was sent */ typedef uint16_t ring_buffer_pos_t;
#define XON_XOFF_CHAR_MASK (uint8_t)0x1F /* XON / XOFF character to send */ #else
typedef uint8_t ring_buffer_pos_t;
extern uint8_t xon_xoff_state;
// XON / XOFF character definitions
#define XON_CHAR (uint8_t)17
#define XOFF_CHAR (uint8_t)19
#endif #endif
#if ENABLED(SERIAL_STATS_DROPPED_RX) #if ENABLED(SERIAL_STATS_DROPPED_RX)
extern uint8_t rx_dropped_bytes; extern uint8_t rx_dropped_bytes;
#endif #endif
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
extern ring_buffer_pos_t rx_max_enqueued; extern ring_buffer_pos_t rx_max_enqueued;
#endif #endif
class MarlinSerial { //: public Stream class MarlinSerial { //: public Stream
@ -157,14 +128,15 @@
static uint8_t availableForWrite(void); static uint8_t availableForWrite(void);
static void flushTX(void); static void flushTX(void);
#endif #endif
static void writeNoHandshake(uint8_t c); static void writeNoHandshake(const uint8_t c);
#if ENABLED(SERIAL_STATS_DROPPED_RX) #if ENABLED(SERIAL_STATS_DROPPED_RX)
static uint32_t dropped() { return rx_dropped_bytes; } FORCE_INLINE static uint32_t dropped() { return rx_dropped_bytes; }
#endif #endif
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
static ring_buffer_pos_t rxMaxEnqueued() { return rx_max_enqueued; } #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
#endif FORCE_INLINE static ring_buffer_pos_t rxMaxEnqueued() { return rx_max_enqueued; }
#endif
private: private:
static void printNumber(unsigned long, const uint8_t); static void printNumber(unsigned long, const uint8_t);

@ -1097,7 +1097,7 @@ inline void get_serial_commands() {
int c; int c;
while (commands_in_queue < BUFSIZE && (c = MYSERIAL.read()) >= 0) { while (commands_in_queue < BUFSIZE && (c = MYSERIAL.read()) >= 0) {
char serial_char = c; char serial_char = c;
/** /**
* If the character ends the line * If the character ends the line
@ -13330,12 +13330,15 @@ void loop() {
// M29 closes the file // M29 closes the file
card.closefile(); card.closefile();
SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED); SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED);
#if ENABLED(SERIAL_STATS_DROPPED_RX)
SERIAL_ECHOLNPAIR("Dropped bytes: ", MarlinSerial::dropped()); #if ENABLED(SERIAL_STATS_DROPPED_RX)
#endif SERIAL_ECHOLNPAIR("Dropped bytes: ", customizedSerial.dropped());
#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) #endif
SERIAL_ECHOLNPAIR("Max RX Queue Size: ", MarlinSerial::rxMaxEnqueued());
#endif #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
SERIAL_ECHOLNPAIR("Max RX Queue Size: ", customizedSerial.rxMaxEnqueued());
#endif
ok_to_send(); ok_to_send();
} }
else { else {

@ -100,7 +100,7 @@
#define SET_BIT(n,b,value) (n) ^= ((-value)^(n)) & (_BV(b)) #define SET_BIT(n,b,value) (n) ^= ((-value)^(n)) & (_BV(b))
// Macro to check that a number if a power if 2 // Macro to check that a number if a power if 2
#define IS_POWEROF2(x) ((x) && !((x) & ((x) - 1))) #define IS_POWER_OF_2(x) ((x) && !((x) & ((x) - 1)))
// Macros for maths shortcuts // Macros for maths shortcuts
#ifndef M_PI #ifndef M_PI

Loading…
Cancel
Save