forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

More redundant temp sensor changes. (After testing and debugging by reifsnderb)

Browse Source
master
Erik van der Zalm 11 years ago
parent 9be61cdc02
commit 5090c56651
5 changed files with 196 additions and 175 deletions
Show Stats Download Patch File Download Diff File

4
Marlin/Configuration.h
Unescape View File

@ -93,8 +93,8 @@
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. // This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Actual temperature must be close to target for this long before M109 returns success // Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_RESIDENCY_TIME 10 // (seconds)

6
Marlin/Configuration_adv.h
Unescape View File

@ -318,6 +318,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
//=========================================================================== //===========================================================================
//============================= Define Defines ============================ //============================= Define Defines ============================
//=========================================================================== //===========================================================================
#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
#error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
#endif
#if TEMP_SENSOR_0 > 0 #if TEMP_SENSOR_0 > 0
#define THERMISTORHEATER_0 TEMP_SENSOR_0 #define THERMISTORHEATER_0 TEMP_SENSOR_0
@ -367,8 +370,5 @@ const unsigned int dropsegments=5; //everything with less than this number of st
#undef BED_MAXTEMP #undef BED_MAXTEMP
#endif #endif
#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
#error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
#endif
#endif //__CONFIGURATION_ADV_H #endif //__CONFIGURATION_ADV_H

4
Marlin/Marlin_main.cpp
Unescape View File

@ -1055,7 +1055,7 @@ void process_commands()
case 105 : // M105 case 105 : // M105
if(setTargetedHotend(105)){ if(setTargetedHotend(105)){
break; break;
} }
#if defined(TEMP_0_PIN) && TEMP_0_PIN > -1 #if defined(TEMP_0_PIN) && TEMP_0_PIN > -1
SERIAL_PROTOCOLPGM("ok T:"); SERIAL_PROTOCOLPGM("ok T:");
SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1);
@ -2278,4 +2278,4 @@ bool setTargetedHotend(int code){
} }
} }
return false; return false;
} }

327
Marlin/pins.h
Unescape View File

@ -313,189 +313,200 @@
#if MOTHERBOARD == 33 || MOTHERBOARD == 34 #if MOTHERBOARD == 33 || MOTHERBOARD == 34
#define LARGE_FLASH true #define LARGE_FLASH true
#define X_STEP_PIN 54
#define X_DIR_PIN 55
#define X_ENABLE_PIN 38
#define X_MIN_PIN 3
#define X_MAX_PIN 2
#define Y_STEP_PIN 60
#define Y_DIR_PIN 61
#define Y_ENABLE_PIN 56
#define Y_MIN_PIN 14
#define Y_MAX_PIN 15
#define Z_STEP_PIN 46
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 62
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19
#define Z2_STEP_PIN 36
#define Z2_DIR_PIN 34
#define Z2_ENABLE_PIN 30
#define E0_STEP_PIN 26
#define E0_DIR_PIN 28
#define E0_ENABLE_PIN 24
#define E1_STEP_PIN 36
#define E1_DIR_PIN 34
#define E1_ENABLE_PIN 30
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#if MOTHERBOARD == 33
#define FAN_PIN 9 // (Sprinter config)
#else
#define FAN_PIN 4 // IO pin. Buffer needed
#endif
#define X_STEP_PIN 54 #define PS_ON_PIN 12
#define X_DIR_PIN 55
#define X_ENABLE_PIN 38
#define X_MIN_PIN 3
#define X_MAX_PIN 2
#define Y_STEP_PIN 60 #if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
#define Y_DIR_PIN 61 #define KILL_PIN 41
#define Y_ENABLE_PIN 56 #else
#define Y_MIN_PIN 14 #define KILL_PIN -1
#define Y_MAX_PIN 15 #endif
#define Z_STEP_PIN 46 #define HEATER_0_PIN 10 // EXTRUDER 1
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 62
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19
#define Z2_STEP_PIN 36 #if MOTHERBOARD == 33
#define Z2_DIR_PIN 34 #define HEATER_1_PIN -1
#define Z2_ENABLE_PIN 30 #else
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
#endif
#define E0_STEP_PIN 26 #define HEATER_2_PIN -1
#define E0_DIR_PIN 28 #define TEMP_0_PIN 13 // ANALOG NUMBERING
#define E0_ENABLE_PIN 24 #define TEMP_1_PIN 15 // ANALOG NUMBERING
#define TEMP_2_PIN -1 // ANALOG NUMBERING
#define HEATER_BED_PIN 8 // BED
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#define E1_STEP_PIN 36
#define E1_DIR_PIN 34
#define E1_ENABLE_PIN 30
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#if MOTHERBOARD == 33 #ifdef NUM_SERVOS
#define FAN_PIN 9 // (Sprinter config) #define SERVO0_PIN 11
#else
#define FAN_PIN 4 // IO pin. Buffer needed
#endif
#define PS_ON_PIN 12
#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) #if NUM_SERVOS > 1
#define KILL_PIN 41 #define SERVO1_PIN 6
#else #endif
#define KILL_PIN -1
#endif
#define HEATER_0_PIN 10 // EXTRUDER 1 #if NUM_SERVOS > 2
#if MOTHERBOARD == 33 #define SERVO2_PIN 5
#define HEATER_1_PIN -1 #endif
#else
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
#endif
#define HEATER_2_PIN -1
#define TEMP_0_PIN 13 // ANALOG NUMBERING
#define TEMP_1_PIN 15 // ANALOG NUMBERING
#define TEMP_2_PIN -1 // ANALOG NUMBERING
#define HEATER_BED_PIN 8 // BED
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#ifdef NUM_SERVOS #if NUM_SERVOS > 2
#define SERVO0_PIN 11 #define SERVO3_PIN 4
#if NUM_SERVOS > 1 #endif
#define SERVO1_PIN 6
#endif
#if NUM_SERVOS > 2
#define SERVO2_PIN 5
#endif
#if NUM_SERVOS > 2
#define SERVO3_PIN 4
#endif #endif
#endif
#ifdef ULTRA_LCD #ifdef ULTRA_LCD
#ifdef NEWPANEL #ifdef NEWPANEL
#define LCD_PINS_RS 16 #define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17 #define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23 #define LCD_PINS_D4 23
#define LCD_PINS_D5 25 #define LCD_PINS_D5 25
#define LCD_PINS_D6 27 #define LCD_PINS_D6 27
#define LCD_PINS_D7 29 #define LCD_PINS_D7 29
#ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
#define BEEPER 37
#define BTN_EN1 31 #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
#define BTN_EN2 33 #define BEEPER 37
#define BTN_ENC 35
#define SDCARDDETECT 49 #define BTN_EN1 31
#else #define BTN_EN2 33
//arduino pin which triggers an piezzo beeper #define BTN_ENC 35
#define BEEPER 33 // Beeper on AUX-4
//buttons are directly attached using AUX-2
#ifdef REPRAPWORLD_KEYPAD
#define BTN_EN1 64 // encoder
#define BTN_EN2 59 // encoder
#define BTN_ENC 63 // enter button
#define SHIFT_OUT 40 // shift register
#define SHIFT_CLK 44 // shift register
#define SHIFT_LD 42 // shift register
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31 //the click
#endif
#ifdef G3D_PANEL
#define SDCARDDETECT 49 #define SDCARDDETECT 49
#else #else
#define SDCARDDETECT -1 // Ramps does not use this port //arduino pin which triggers an piezzo beeper
#define BEEPER 33 // Beeper on AUX-4
//buttons are directly attached using AUX-2
#ifdef REPRAPWORLD_KEYPAD
#define BTN_EN1 64 // encoder
#define BTN_EN2 59 // encoder
#define BTN_ENC 63 // enter button
#define SHIFT_OUT 40 // shift register
#define SHIFT_CLK 44 // shift register
#define SHIFT_LD 42 // shift register
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31 //the click
#endif
#ifdef G3D_PANEL
#define SDCARDDETECT 49
#else
#define SDCARDDETECT -1 // Ramps does not use this port
#endif
#endif #endif
#endif
#else //old style panel with shift register #else //old style panel with shift register
//arduino pin witch triggers an piezzo beeper //arduino pin witch triggers an piezzo beeper
#define BEEPER 33 // No Beeper added #define BEEPER 33 // No Beeper added
//buttons are attached to a shift register //buttons are attached to a shift register
// Not wired this yet // Not wired this yet
//#define SHIFT_CLK 38 //#define SHIFT_CLK 38
//#define SHIFT_LD 42 //#define SHIFT_LD 42
//#define SHIFT_OUT 40 //#define SHIFT_OUT 40
//#define SHIFT_EN 17 //#define SHIFT_EN 17
#define LCD_PINS_RS 16 #define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17 #define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23 #define LCD_PINS_D4 23
#define LCD_PINS_D5 25 #define LCD_PINS_D5 25
#define LCD_PINS_D6 27 #define LCD_PINS_D6 27
#define LCD_PINS_D7 29 #define LCD_PINS_D7 29
#endif #endif
#endif //ULTRA_LCD #endif //ULTRA_LCD
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (MOTHERBOARD == 3) #else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (MOTHERBOARD == 3)
#define X_STEP_PIN 26 #define X_STEP_PIN 26
#define X_DIR_PIN 28 #define X_DIR_PIN 28
#define X_ENABLE_PIN 24 #define X_ENABLE_PIN 24
#define X_MIN_PIN 3 #define X_MIN_PIN 3
#define X_MAX_PIN -1 //2 #define X_MAX_PIN -1 //2
#define Y_STEP_PIN 38 #define Y_STEP_PIN 38
#define Y_DIR_PIN 40 #define Y_DIR_PIN 40
#define Y_ENABLE_PIN 36 #define Y_ENABLE_PIN 36
#define Y_MIN_PIN 16 #define Y_MIN_PIN 16
#define Y_MAX_PIN -1 //17 #define Y_MAX_PIN -1 //17
#define Z_STEP_PIN 44 #define Z_STEP_PIN 44
#define Z_DIR_PIN 46 #define Z_DIR_PIN 46
#define Z_ENABLE_PIN 42 #define Z_ENABLE_PIN 42
#define Z_MIN_PIN 18 #define Z_MIN_PIN 18
#define Z_MAX_PIN -1 //19 #define Z_MAX_PIN -1 //19
#define E0_STEP_PIN 32
#define E0_DIR_PIN 34
#define E0_ENABLE_PIN 30
#define SDPOWER 48
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN -1
#define KILL_PIN -1
#ifdef RAMPS_V_1_0 // RAMPS_V_1_0
#define HEATER_0_PIN 12 // RAMPS 1.0
#define HEATER_BED_PIN -1 // RAMPS 1.0
#define FAN_PIN 11 // RAMPS 1.0
#else // RAMPS_V_1_1 or RAMPS_V_1_2
#define HEATER_0_PIN 10 // RAMPS 1.1
#define HEATER_BED_PIN 8 // RAMPS 1.1
#define FAN_PIN 9 // RAMPS 1.1
#endif
#define E0_STEP_PIN 32 #define HEATER_1_PIN -1
#define E0_DIR_PIN 34 #define HEATER_2_PIN -1
#define E0_ENABLE_PIN 30 #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define SDPOWER 48
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN -1
#define KILL_PIN -1
#ifdef RAMPS_V_1_0 // RAMPS_V_1_0
#define HEATER_0_PIN 12 // RAMPS 1.0
#define HEATER_BED_PIN -1 // RAMPS 1.0
#define FAN_PIN 11 // RAMPS 1.0
#else // RAMPS_V_1_1 or RAMPS_V_1_2
#define HEATER_0_PIN 10 // RAMPS 1.1
#define HEATER_BED_PIN 8 // RAMPS 1.1
#define FAN_PIN 9 // RAMPS 1.1
#endif
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#endif// MOTHERBOARD == 33 || MOTHERBOARD == 34 #endif// MOTHERBOARD == 33 || MOTHERBOARD == 34
// SPI for Max6675 Thermocouple // SPI for Max6675 Thermocouple
@ -1618,4 +1629,4 @@
HEATER_BED_PIN, FAN_PIN, \ HEATER_BED_PIN, FAN_PIN, \
_E0_PINS _E1_PINS _E2_PINS \ _E0_PINS _E1_PINS _E2_PINS \
analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) } analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
#endif #endif

30
Marlin/temperature.cpp
Unescape View File

@ -107,15 +107,15 @@ static volatile bool temp_meas_ready = false;
(defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1)
static unsigned long extruder_autofan_last_check; static unsigned long extruder_autofan_last_check;
#endif #endif
#if EXTRUDERS > 3 #if EXTRUDERS > 3
# error Unsupported number of extruders # error Unsupported number of extruders
#elif EXTRUDERS > 2 #elif EXTRUDERS > 2
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2, v3 } # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2, v3 }
#elif EXTRUDERS > 1 #elif EXTRUDERS > 1
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2 } # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2 }
#else #else
# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1 } # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1 }
#endif #endif
// Init min and max temp with extreme values to prevent false errors during startup // Init min and max temp with extreme values to prevent false errors during startup
@ -127,8 +127,14 @@ static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 16383, 16383, 16383 );
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP; static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
#endif #endif
static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE );
static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN ); #ifdef TEMP_SENSOR_1_AS_REDUNDANT
static void *heater_ttbl_map[2] = {(void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE };
static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN };
#else
static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE );
static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN );
#endif
static float analog2temp(int raw, uint8_t e); static float analog2temp(int raw, uint8_t e);
static float analog2tempBed(int raw); static float analog2tempBed(int raw);
@ -475,11 +481,11 @@ void manage_heater()
} }
#endif #endif
#ifdef TEMP_SENSOR_1_AS_REDUNDANT #ifdef TEMP_SENSOR_1_AS_REDUNDANT
if(fabs(current_temperature[1] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) { if(fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) {
disable_heater(); disable_heater();
if(IsStopped() == false) { if(IsStopped() == false) {
SERIAL_ERROR_START; SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Extruder switched off. Temperature difference between temp sensors is to high !"); SERIAL_ERRORLNPGM("Extruder switched off. Temperature difference between temp sensors is too high !");
LCD_ALERTMESSAGEPGM("Err: REDUNDANT TEMP ERROR"); LCD_ALERTMESSAGEPGM("Err: REDUNDANT TEMP ERROR");
} }
#ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
@ -580,7 +586,11 @@ void manage_heater()
// Derived from RepRap FiveD extruder::getTemperature() // Derived from RepRap FiveD extruder::getTemperature()
// For hot end temperature measurement. // For hot end temperature measurement.
static float analog2temp(int raw, uint8_t e) { static float analog2temp(int raw, uint8_t e) {
#ifdef TEMP_SENSOR_1_AS_REDUNDANT
if(e > EXTRUDERS)
#else
if(e >= EXTRUDERS) if(e >= EXTRUDERS)
#endif
{ {
SERIAL_ERROR_START; SERIAL_ERROR_START;
SERIAL_ERROR((int)e); SERIAL_ERROR((int)e);
@ -660,7 +670,7 @@ static void updateTemperaturesFromRawValues()
} }
current_temperature_bed = analog2tempBed(current_temperature_bed_raw); current_temperature_bed = analog2tempBed(current_temperature_bed_raw);
#ifdef TEMP_SENSOR_1_AS_REDUNDANT #ifdef TEMP_SENSOR_1_AS_REDUNDANT
redundant_temperature =analog2temp(redundant_temperature_raw, 1); redundant_temperature = analog2temp(redundant_temperature_raw, 1);
#endif #endif
//Reset the watchdog after we know we have a temperature measurement. //Reset the watchdog after we know we have a temperature measurement.
watchdog_reset(); watchdog_reset();

Write Preview
Loading…
Cancel
Save