Cosmetic patches

Marlin/Marlin_main.cpp

@@ -616,12 +616,12 @@ static uint8_t target_extruder;
 float cartes[XYZ] = { 0 };
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
-  bool filament_sensor = false;  //M405 turns on filament_sensor control, M406 turns it off
+  bool filament_sensor = false;                                 // M405 turns on filament sensor control. M406 turns it off.
-  float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA,  // Nominal filament width. Change with M404
+  float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA,  // Nominal filament width. Change with M404.
         filament_width_meas = DEFAULT_MEASURED_FILAMENT_DIA;    // Measured filament diameter
   int8_t measurement_delay[MAX_MEASUREMENT_DELAY + 1];          // Ring buffer to delayed measurement. Store extruder factor after subtracting 100
   int filwidth_delay_index[2] = { 0, -1 };                      // Indexes into ring buffer
-  int meas_delay_cm = MEASUREMENT_DELAY_CM;  //distance delay setting
+  int meas_delay_cm = MEASUREMENT_DELAY_CM;                     // Distance delay setting
 #endif
 
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
@@ -8220,10 +8220,10 @@ inline void gcode_M400() { stepper.synchronize(); }
     NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
 
     if (filwidth_delay_index[1] == -1) { // Initialize the ring buffer if not done since startup
-      int temp_ratio = thermalManager.widthFil_to_size_ratio();
+      const int temp_ratio = thermalManager.widthFil_to_size_ratio() - 100; // -100 to scale within a signed byte
 
       for (uint8_t i = 0; i < COUNT(measurement_delay); ++i)
-        measurement_delay[i] = temp_ratio - 100;  // Subtract 100 to scale within a signed byte
+        measurement_delay[i] = temp_ratio;
 
       filwidth_delay_index[0] = filwidth_delay_index[1] = 0;
     }
@@ -10279,7 +10279,7 @@ void process_next_command() {
         case 407:   // M407: Display measured filament diameter
           gcode_M407();
           break;
-      #endif // ENABLED(FILAMENT_WIDTH_SENSOR)
+      #endif // FILAMENT_WIDTH_SENSOR
 
       #if PLANNER_LEVELING
         case 420: // M420: Enable/Disable Bed Leveling

Marlin/printcounter.cpp

@@ -188,7 +188,8 @@ bool PrintCounter::start() {
     }
     return true;
   }
-  else return false;
+
+  return false;
 }
 
 // @Override

Marlin/printcounter.h

@@ -32,12 +32,12 @@
 // Print debug messages with M111 S2
 //#define DEBUG_PRINTCOUNTER
 
-struct printStatistics {    // 13 bytes
+struct printStatistics {    // 16 bytes (20 with real doubles)
   //const uint8_t magic;    // Magic header, it will always be 0x16
   uint16_t totalPrints;     // Number of prints
   uint16_t finishedPrints;  // Number of complete prints
   uint32_t printTime;       // Accumulated printing time
-  uint32_t longestPrint;    // Longest successfull print job
+  uint32_t longestPrint;    // Longest successful print job
   double   filamentUsed;    // Accumulated filament consumed in mm
 };
 

Marlin/temperature.cpp

@@ -961,8 +961,8 @@ void Temperature::updateTemperaturesFromRawValues() {
  */
 void Temperature::init() {
 
-  #if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1))
+  #if MB(RUMBA) && (TEMP_SENSOR_0 == -1 || TEMP_SENSOR_1 == -1 || TEMP_SENSOR_2 == -1 || TEMP_SENSOR_BED == -1)
-    //disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
+    // Disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
     MCUCR = _BV(JTD);
     MCUCR = _BV(JTD);
   #endif