Change default to 4°C in 16s

master
Scott Lahteine 10 years ago
parent 54deb9eea3
commit 6110494a56

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 40000 //40 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 10 //Heat up at least 10 degree in 20 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

@ -19,8 +19,8 @@
// If the temperature has not increased at the end of that period, the target temperature is set to zero. // If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and // It can be reset with another M104/M109. This check is also only triggered if the target temperature and
// the current temperature differ by at least 2x WATCH_TEMP_INCREASE // the current temperature differ by at least 2x WATCH_TEMP_INCREASE
#define WATCH_TEMP_PERIOD 10000 // 10 seconds #define WATCH_TEMP_PERIOD 16000 // 16 seconds
#define WATCH_TEMP_INCREASE 2 // Heat up at least 2 degrees in 10 seconds #define WATCH_TEMP_INCREASE 4 // Heat up at least 4 degrees in 16 seconds
#ifdef PIDTEMP #ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.

Loading…
Cancel
Save