|
|
|
|
@ -9436,6 +9436,39 @@ inline void gcode_M503() {
|
|
|
|
|
|
|
|
|
|
#endif // ADVANCED_PAUSE_FEATURE
|
|
|
|
|
|
|
|
|
|
#if ENABLED(MK2_MULTIPLEXER)
|
|
|
|
|
|
|
|
|
|
inline void select_multiplexed_stepper(const uint8_t e) {
|
|
|
|
|
stepper.synchronize();
|
|
|
|
|
disable_e_steppers();
|
|
|
|
|
WRITE(E_MUX0_PIN, TEST(e, 0) ? HIGH : LOW);
|
|
|
|
|
WRITE(E_MUX1_PIN, TEST(e, 1) ? HIGH : LOW);
|
|
|
|
|
WRITE(E_MUX2_PIN, TEST(e, 2) ? HIGH : LOW);
|
|
|
|
|
safe_delay(100);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* M702: Unload all extruders
|
|
|
|
|
*/
|
|
|
|
|
inline void gcode_M702() {
|
|
|
|
|
for (uint8_t s = 0; s < E_STEPPERS; s++) {
|
|
|
|
|
select_multiplexed_stepper(e);
|
|
|
|
|
// TODO: standard unload filament function
|
|
|
|
|
// MK2 firmware behavior:
|
|
|
|
|
// - Make sure temperature is high enough
|
|
|
|
|
// - Raise Z to at least 15 to make room
|
|
|
|
|
// - Extrude 1cm of filament in 1 second
|
|
|
|
|
// - Under 230C quickly purge ~12mm, over 230C purge ~10mm
|
|
|
|
|
// - Change E max feedrate to 80, eject the filament from the tube. Sync.
|
|
|
|
|
// - Restore E max feedrate to 50
|
|
|
|
|
}
|
|
|
|
|
// Go back to the last active extruder
|
|
|
|
|
select_multiplexed_stepper(active_extruder);
|
|
|
|
|
disable_e_steppers();
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#endif // MK2_MULTIPLEXER
|
|
|
|
|
|
|
|
|
|
#if ENABLED(DUAL_X_CARRIAGE)
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
@ -10257,15 +10290,24 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
|
|
|
|
|
UNUSED(fr_mm_s);
|
|
|
|
|
UNUSED(no_move);
|
|
|
|
|
|
|
|
|
|
// Set the new active extruder
|
|
|
|
|
active_extruder = tmp_extruder;
|
|
|
|
|
#if ENABLED(SWITCHING_EXTRUDER) && !DONT_SWITCH
|
|
|
|
|
|
|
|
|
|
#endif // HOTENDS <= 1
|
|
|
|
|
stepper.synchronize();
|
|
|
|
|
move_extruder_servo(tmp_extruder);
|
|
|
|
|
|
|
|
|
|
#elif ENABLED(MK2_MULTIPLEXER)
|
|
|
|
|
|
|
|
|
|
if (tmp_extruder >= E_STEPPERS)
|
|
|
|
|
return invalid_extruder_error(tmp_extruder);
|
|
|
|
|
|
|
|
|
|
select_multiplexed_stepper(tmp_extruder);
|
|
|
|
|
|
|
|
|
|
#if ENABLED(SWITCHING_EXTRUDER) && !DONT_SWITCH
|
|
|
|
|
move_extruder_servo(active_extruder);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#endif // HOTENDS <= 1
|
|
|
|
|
|
|
|
|
|
active_extruder = tmp_extruder;
|
|
|
|
|
|
|
|
|
|
SERIAL_ECHO_START();
|
|
|
|
|
SERIAL_ECHOLNPAIR(MSG_ACTIVE_EXTRUDER, (int)active_extruder);
|
|
|
|
|
|
|
|
|
|
@ -11001,6 +11043,12 @@ void process_next_command() {
|
|
|
|
|
break;
|
|
|
|
|
#endif // DUAL_X_CARRIAGE
|
|
|
|
|
|
|
|
|
|
#if ENABLED(MK2_MULTIPLEXER)
|
|
|
|
|
case 702: // M702: Unload all extruders
|
|
|
|
|
gcode_M702();
|
|
|
|
|
break;
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LIN_ADVANCE)
|
|
|
|
|
case 900: // M900: Set advance K factor.
|
|
|
|
|
gcode_M900();
|
|
|
|
|
@ -12968,6 +13016,12 @@ void setup() {
|
|
|
|
|
#endif
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(MK2_MULTIPLEXER)
|
|
|
|
|
SET_OUTPUT(E_MUX0_PIN);
|
|
|
|
|
SET_OUTPUT(E_MUX1_PIN);
|
|
|
|
|
SET_OUTPUT(E_MUX2_PIN);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
lcd_init();
|
|
|
|
|
#if ENABLED(SHOW_BOOTSCREEN)
|
|
|
|
|
#if ENABLED(DOGLCD)
|
|
|
|
|
|
Scott Lahteine
8 years ago
committed by