@ -51,9 +51,6 @@
IntersectionDistance [ s1_ , s2_ , a_ , d_ ] : = ( 2 a d - s1 ^ 2 + s2 ^ 2 ) / ( 4 a )
*/
# include "Marlin.h"
# include "planner.h"
# include "stepper.h"
@ -377,20 +374,26 @@ void plan_init() {
void getHighESpeed ( )
{
static float oldt = 0 ;
if ( ! autotemp_enabled )
if ( ! autotemp_enabled ) {
return ;
if ( degTargetHotend0 ( ) + 2 < autotemp_min ) //probably temperature set to zero.
}
if ( degTargetHotend0 ( ) + 2 < autotemp_min ) { //probably temperature set to zero.
return ; //do nothing
}
float high = ;
float high = 0. ;
uint8_t block_index = block_buffer_tail ;
while ( block_index ! = block_buffer_head ) {
float se = block_buffer [ block_index ] . steps_e / float ( block_buffer [ block_index ] . step_event_count ) * block_buffer [ block_index ] . nominal_rate ;
//se; units steps/sec;
if ( se > high )
{
high = se ;
if ( ( block_buffer [ block_index ] . steps_x ! = 0 ) | |
( block_buffer [ block_index ] . steps_y ! = 0 ) | |
( block_buffer [ block_index ] . steps_z ! = 0 ) ) {
float se = ( float ( block_buffer [ block_index ] . steps_e ) / float ( block_buffer [ block_index ] . step_event_count ) ) * block_buffer [ block_index ] . nominal_speed ;
//se; mm/sec;
if ( se > high )
{
high = se ;
}
}
block_index = ( block_index + 1 ) & ( BLOCK_BUFFER_SIZE - 1 ) ;
}
@ -407,10 +410,6 @@ void getHighESpeed()
}
oldt = t ;
setTargetHotend0 ( t ) ;
// SERIAL_ECHO_START;
// SERIAL_ECHOPAIR("highe",high);
// SERIAL_ECHOPAIR(" t",t);
// SERIAL_ECHOLN("");
}
# endif
@ -456,6 +455,9 @@ void check_axes_activity() {
analogWrite ( FAN_PIN , tail_fan_speed ) ;
}
# endif
# ifdef AUTOTEMP
getHighESpeed ( ) ;
# endif
}
@ -517,7 +519,7 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
block - > step_event_count = max ( block - > steps_x , max ( block - > steps_y , max ( block - > steps_z , block - > steps_e ) ) ) ;
// Bail if this is a zero-length block
if ( block - > step_event_count < = dropsegments ) { return ; } ;
if ( block - > step_event_count < = dropsegments ) { return ; } ;
block - > fan_speed = FanSpeed ;
@ -540,7 +542,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
// Enable all
if ( block - > steps_e ! = 0 ) { enable_e0 ( ) ; enable_e1 ( ) ; enable_e2 ( ) ; }
if ( block - > steps_e = = 0 ) {
if ( feed_rate < mintravelfeedrate ) feed_rate = mintravelfeedrate ;
}
@ -548,12 +549,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
if ( feed_rate < minimumfeedrate ) feed_rate = minimumfeedrate ;
}
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
int moves_queued = ( block_buffer_head - block_buffer_tail + BLOCK_BUFFER_SIZE ) & ( BLOCK_BUFFER_SIZE - 1 ) ;
# ifdef SLOWDOWN
if ( moves_queued < ( BLOCK_BUFFER_SIZE * 0.5 ) & & moves_queued > 1 ) feed_rate = feed_rate * moves_queued / ( BLOCK_BUFFER_SIZE * 0.5 ) ;
# endif
float delta_mm [ 4 ] ;
delta_mm [ X_AXIS ] = ( target [ X_AXIS ] - position [ X_AXIS ] ) / axis_steps_per_unit [ X_AXIS ] ;
delta_mm [ Y_AXIS ] = ( target [ Y_AXIS ] - position [ Y_AXIS ] ) / axis_steps_per_unit [ Y_AXIS ] ;
@ -569,34 +564,33 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
// Calculate speed in mm/second for each axis. No divide by zero due to previous checks.
float inverse_second = feed_rate * inverse_millimeters ;
block - > nominal_speed = block - > millimeters * inverse_second ; // (mm/sec) Always > 0
block - > nominal_rate = ceil ( block - > step_event_count * inverse_second ) ; // (step/sec) Always > 0
int moves_queued = ( block_buffer_head - block_buffer_tail + BLOCK_BUFFER_SIZE ) & ( BLOCK_BUFFER_SIZE - 1 ) ;
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
# ifdef OLD_SLOWDOWN
if ( moves_queued < ( BLOCK_BUFFER_SIZE * 0.5 ) & & moves_queued > 1 ) feed_rate = feed_rate * moves_queued / ( BLOCK_BUFFER_SIZE * 0.5 ) ;
# endif
/*
# ifdef SLOWDOWN
// segment time im micro seconds
long segment_time = lround ( 1000000.0 / inverse_second ) ;
if ( ( blockcount> 0 ) & & ( blockcount < ( BLOCK_BUFFER_SIZE - 4 ) ) ) {
if ( segment_time < minsegmenttime ) { // buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
segment_time= segment_time + lround ( 2 * ( minsegmenttime - segment_time ) / blockcount ) ;
unsigned long segment_time = lround ( 1000000.0 / inverse_second ) ;
if ( ( moves_queued > 1 ) & & ( moves_queued < ( BLOCK_BUFFER_SIZE * 0.5 ) ) ) {
if ( segment_time < minsegmenttime ) { // buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
inverse_second= 1000000.0 / ( segment_time + lround ( 2 * ( minsegmenttime - segment_time ) / moves_queued) ) ;
}
}
else {
if ( segment_time < minsegmenttime ) segment_time = minsegmenttime ;
}
# endif
// END OF SLOW DOWN SECTION
*/
// Calculate speed in mm/sec for each axis
float current_speed [ 4 ] ;
for ( int i = 0 ; i < 4 ; i + + ) {
current_speed [ i ] = delta_mm [ i ] * inverse_second ;
}
block - > nominal_speed = block - > millimeters * inverse_second ; // (mm/sec) Always > 0
block - > nominal_rate = ceil ( block - > step_event_count * inverse_second ) ; // (step/sec) Always > 0
// Limit speed per axis
// Calculate and limit speed in mm/sec for each axis
float current_speed [ 4 ] ;
float speed_factor = 1.0 ; //factor <=1 do decrease speed
for ( int i = 0 ; i < 4 ; i + + ) {
current_speed [ i ] = delta_mm [ i ] * inverse_second ;
if ( abs ( current_speed [ i ] ) > max_feedrate [ i ] )
speed_factor = min ( speed_factor , max_feedrate [ i ] / abs ( current_speed [ i ] ) ) ;
}
@ -633,17 +627,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
// Correct the speed
if ( speed_factor < 1.0 ) {
// Serial.print("speed factor : "); Serial.println(speed_factor);
for ( int i = 0 ; i < 4 ; i + + ) {
if ( abs ( current_speed [ i ] ) > max_feedrate [ i ] )
speed_factor = min ( speed_factor , max_feedrate [ i ] / abs ( current_speed [ i ] ) ) ;
/*
if ( speed_factor < 0.1 ) {
Serial . print ( " speed factor : " ) ; Serial . println ( speed_factor ) ;
Serial . print ( " current_speed " ) ; Serial . print ( i ) ; Serial . print ( " : " ) ; Serial . println ( current_speed [ i ] ) ;
}
*/
}
for ( unsigned char i = 0 ; i < 4 ; i + + ) {
current_speed [ i ] * = speed_factor ;
}
@ -784,9 +767,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
*/
# endif // ADVANCE
calculate_trapezoid_for_block ( block , block - > entry_speed / block - > nominal_speed ,
MINIMUM_PLANNER_SPEED / block - > nominal_speed ) ;
@ -797,9 +777,7 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
memcpy ( position , target , sizeof ( target ) ) ; // position[] = target[]
planner_recalculate ( ) ;
# ifdef AUTOTEMP
getHighESpeed ( ) ;
# endif
st_wake_up ( ) ;
}
Erik van der Zalm
13 years ago