//#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
//#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
//#define BLTOUCH_HEATERS_OFF // if defined the printer's heaters are turned off during probe event
/**
@ -601,7 +606,7 @@
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
/**
*ZProbetonozzle(X,Y)offset,relativeto(0,0).
@ -630,8 +635,10 @@
#define XY_PROBE_SPEED 7500
// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 6 // Z Clearance between probe points
//
// For M851 give a range for adjusting the Z probe offset
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
@ -792,9 +790,9 @@
#define X_MIN_POS 0
#define Y_MIN_POS 0
#define Z_MIN_POS 0
#define X_MAX_POS 420// These numbers are not accurate for an unaltered gMax 1.5+ printer. My print bed
#define Y_MAX_POS 420// is inset a noticable amount from the edge of the bed. Combined with the inset,
// the nozzle can reach all cordinates of the mesh.
#define X_MAX_POS 420// These numbers are not accurate for an unaltered gMax 1.5+ printer. My print bed
#define Y_MAX_POS 420// is inset a noticable amount from the edge of the bed. Combined with the inset,
// the nozzle can reach all cordinates of the mesh.
#define Z_MAX_POS 500
// If enabled, axes won't move below MIN_POS in response to movement commands.
@ -994,8 +992,8 @@
#define Z_SAFE_HOMING
#if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT (((X_MIN_POS+X_MAX_POS)/2)-4) // X point for Z homing when homing all axis (G28).
#define Z_SAFE_HOMING_Y_POINT (((Y_MIN_POS+Y_MAX_POS)/2)+4) // Y point for Z homing when homing all axis (G28).
#define Z_SAFE_HOMING_X_POINT (((X_MIN_POS+X_MAX_POS)/2)-4) // X point for Z homing when homing all axis (G28).
#define Z_SAFE_HOMING_Y_POINT (((Y_MIN_POS+Y_MAX_POS)/2)+4) // Y point for Z homing when homing all axis (G28).
#endif
// Homing speeds (mm/m)
@ -1035,7 +1033,7 @@
//
// M100 Free Memory Watcher
//
#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
//
// G20/G21 Inch mode support
@ -1619,7 +1617,7 @@
*/
//#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
@ -1633,6 +1631,6 @@
// Display filament width on the LCD status line. Status messages will expire after 5 seconds.
Scott Lahteine
8 years ago