Split RAMPS 1.3 an 1.4 (PR#2741)

because of hardware differences on the SERVO0_PIN
master
AnHardt 9 years ago committed by Richard Wackerbarth
parent 6dfc7124a1
commit 8da2e98985

@ -98,6 +98,30 @@ MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),34)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),35)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),36)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),38)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),43)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),44)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),45)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),46)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),48)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Gen6
else ifeq ($(HARDWARE_MOTHERBOARD),5)

@ -10,13 +10,18 @@
#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0
#define BOARD_SETHI 20 // Sethi 3D_1
#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
#define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 / 1.4 (Power outputs: Spindle, Controller Fan)
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 (Power outputs: Extruder, Fan, Bed)
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Bed)
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 (Power outputs: Extruder, Fan, Fan)
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Fan)
#define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 (Power outputs: Spindle, Controller Fan)
#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like)
#define BOARD_RIGIDBOARD 42 // Invent-A-Part RigidBoard
#define BOARD_RAMPS_14_EFB 43 // RAMPS 1.4 (Power outputs: Extruder, Fan, Bed)
#define BOARD_RAMPS_14_EEB 44 // RAMPS 1.4 (Power outputs: Extruder0, Extruder1, Bed)
#define BOARD_RAMPS_14_EFF 45 // RAMPS 1.4 (Power outputs: Extruder, Fan, Fan)
#define BOARD_RAMPS_14_EEF 46 // RAMPS 1.4 (Power outputs: Extruder0, Extruder1, Fan)
#define BOARD_RAMPS_14_SF 48 // RAMPS 1.4 (Power outputs: Spindle, Controller Fan)
#define BOARD_GEN6 5 // Gen6
#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe
#define BOARD_SANGUINOLOLU_11 6 // Sanguinololu < 1.2

@ -38,6 +38,12 @@
#include "pins_RAMPS_13_EFB.h"
#elif MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF)
#include "pins_RAMPS_13.h"
#elif MB(RAMPS_14_EFB)
#define IS_RAMPS_14
#include "pins_RAMPS_13_EFB.h"
#elif MB(RAMPS_14_EEB) || MB(RAMPS_14_EFF) || MB(RAMPS_14_EEF) || MB(RAMPS_14_SF)
#define IS_RAMPS_14
#include "pins_RAMPS_13.h"
#elif MB(GEN6)
#include "pins_GEN6.h"
#elif MB(GEN6_DELUXE)

@ -1,5 +1,5 @@
/**
* Arduino Mega with RAMPS v1.3 pin assignments
* Arduino Mega with RAMPS v1.3 v1.4 pin assignments
*
* Applies to the following boards:
*
@ -9,7 +9,17 @@
* RAMPS_13_EEF (Extruder, Extruder, Fan)
* RAMPS_13_SF (Spindle, Controller Fan)
*
* RAMPS_14_EFB (Extruder, Fan, Bed)
* RAMPS_14_EEB (Extruder, Extruder, Bed)
* RAMPS_14_EFF (Extruder, Fan, Fan)
* RAMPS_14_EEF (Extruder, Extruder, Fan)
* RAMPS_14_SF (Spindle, Controller Fan)
*
* Other pins_MYBOARD.h files may override these defaults
*
* Differences between
* RAMPS_13 | RAMPS_14
* 7 | 11
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
@ -18,7 +28,11 @@
#define LARGE_FLASH true
#define SERVO0_PIN 11
#ifdef IS_RAMPS_14
#define SERVO0_PIN 11
#else
#define SERVO0_PIN 7 // RAMPS_13 // Will conflict with BTN_EN2 on LCD_I2C_VIKI
#endif
#define SERVO1_PIN 6
#define SERVO2_PIN 5
#define SERVO3_PIN 4
@ -154,7 +168,9 @@
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI)
#define BTN_EN1 22 // reverse if the encoder turns the wrong way.
#define BTN_EN2 7
#define BTN_EN2 7 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf
// tells about 40/42.
// 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49

Loading…
Cancel
Save