forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Fix the PR #4899 (ABL: Enable by type. Bilinear for all.) etc.

Browse Source 
About Configuration.h:
・Fix the PR #4899 (ABL: Enable by type. Bilinear for all.)
Remove Duplicated contents

・Fix the PR #4305 (Custom boot screen feature improvement)
Revert from "during boot" to "during bootup" in all the example
Configuration.h

・Fix the PR #4207 (Clean up, simplify and generalize the Allen-key-probe
code.)
Resolve and relocate the duplicated definitions in Z_PROBE_ALLEN_KEY
section

・Follow-up the PR #4805 (Additional documentation of Configuration.h)
Add forgotten changes to all the example Configuration.h

Adjust spacing

About Configuration_adv.h:
Add missing description of SLOWDOWN for DELTA

Adjust spacing
master
esenapaj 8 years ago committed by Scott Lahteine
parent 8b46eb3766
commit 92c03a44a9
40 changed files with 714 additions and 446 deletions
Show Stats Download Patch File Download Diff File

67
Marlin/Configuration.h
Unescape View File

@ -809,73 +809,6 @@
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
/**
* Select one form of Auto Bed Leveling below.
*
* If you're also using the Probe for Z Homing, it's
* highly recommended to enable Z_SAFE_HOMING also!
*
* - 3POINT
* Probe 3 arbitrary points on the bed (that aren't collinear)
* You specify the XY coordinates of all 3 points.
* The result is a single tilted plane. Best for a flat bed.
*
* - LINEAR
* Probe several points in a grid.
* You specify the rectangle and the density of sample points.
* The result is a single tilted plane. Best for a flat bed.
*
* - BILINEAR
* Probe several points in a grid.
* You specify the rectangle and the density of sample points.
* The result is a mesh, best for large or uneven beds.
*/
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
//#define AUTO_BED_LEVELING_BILINEAR
/**
* Enable detailed logging of G28, G29, M48, etc.
* Turn on with the command 'M111 S32'.
* NOTE: Requires a lot of PROGMEM!
*/
//#define DEBUG_LEVELING_FEATURE
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
// Set the number of grid points per dimension.
#define ABL_GRID_POINTS_X 3
#define ABL_GRID_POINTS_Y ABL_GRID_POINTS_X
// Set the boundaries for probing (where the probe can reach).
#define LEFT_PROBE_BED_POSITION 15
#define RIGHT_PROBE_BED_POSITION 170
#define FRONT_PROBE_BED_POSITION 20
#define BACK_PROBE_BED_POSITION 170
// The Z probe minimum outer margin (to validate G29 parameters).
#define MIN_PROBE_EDGE 10
#elif ENABLED(AUTO_BED_LEVELING_3POINT)
// 3 arbitrary points to probe.
// A simple cross-product is used to estimate the plane of the bed.
#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 180
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
*/
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
// @section homing // @section homing
// The center of the bed is at (X=0, Y=0) // The center of the bed is at (X=0, Y=0)

46
Marlin/example_configurations/Cartesio/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(MaukCC, CartesioE)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(MaukCC, CartesioE)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
#define SHOW_CUSTOM_BOOTSCREEN #define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 115200 #define BAUDRATE 115200
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -170,14 +179,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -822,7 +839,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (10*60) #define HOMING_FEEDRATE_Z (10*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/Felix/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -805,7 +822,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/Felix/DUAL/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -803,7 +820,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/Hephestos/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 115200 #define BAUDRATE 115200
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -172,14 +181,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -814,7 +831,6 @@
#define HOMING_FEEDRATE_XY 2000 #define HOMING_FEEDRATE_XY 2000
#define HOMING_FEEDRATE_Z 150 #define HOMING_FEEDRATE_Z 150
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/Hephestos_2/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "@jbrazio" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "@jbrazio" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
#define SHOW_CUSTOM_BOOTSCREEN #define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -816,7 +833,6 @@
#define HOMING_FEEDRATE_XY (150*60) #define HOMING_FEEDRATE_XY (150*60)
#define HOMING_FEEDRATE_Z 200 #define HOMING_FEEDRATE_Z 200
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/K8200/Configuration.h
Unescape View File

@ -95,8 +95,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(K8200, @CONSULitAS)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(K8200, @CONSULitAS)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -112,15 +112,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -176,14 +185,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -839,7 +856,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/K8400/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -822,7 +839,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (8*60) #define HOMING_FEEDRATE_Z (8*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/K8400/Dual-head/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -822,7 +839,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (8*60) #define HOMING_FEEDRATE_Z (8*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -822,7 +839,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/RigidBot/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 115200 #define BAUDRATE 115200
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -172,14 +181,22 @@
#define HOTEND_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis #define HOTEND_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis
#define HOTEND_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis #define HOTEND_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -820,7 +837,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (15*60) #define HOMING_FEEDRATE_Z (15*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/SCARA/Configuration.h
Unescape View File

@ -120,8 +120,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -137,15 +137,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -201,14 +210,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -837,7 +854,6 @@
#define HOMING_FEEDRATE_XY (40*60) #define HOMING_FEEDRATE_XY (40*60)
#define HOMING_FEEDRATE_Z (10*60) #define HOMING_FEEDRATE_Z (10*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/TAZ4/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(Aleph Objects, Inc, TAZ config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(Aleph Objects, Inc, TAZ config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -843,7 +860,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (8*60) #define HOMING_FEEDRATE_Z (8*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/WITBOX/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(bq Witbox)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(bq Witbox)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 115200 #define BAUDRATE 115200
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -172,14 +181,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -814,7 +831,6 @@
#define HOMING_FEEDRATE_XY (120*60) #define HOMING_FEEDRATE_XY (120*60)
#define HOMING_FEEDRATE_Z 432 #define HOMING_FEEDRATE_Z 432
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/adafruit/ST7565/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -822,7 +839,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

57
Marlin/example_configurations/delta/biv2.5/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -614,16 +631,16 @@
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE XY_PROBE_SPEED #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE XY_PROBE_SPEED
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z 100.0 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z 100.0
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (XY_PROBE_SPEED)/2 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (XY_PROBE_SPEED)/2
#define Z_PROBE_ALLEN_KEY_DEPLOY_4_X Z_PROBE_ALLEN_KEY_DEPLOY_3_X * 0.75
#define Z_PROBE_ALLEN_KEY_DEPLOY_4_Y Z_PROBE_ALLEN_KEY_DEPLOY_3_Y * 0.75
#define Z_PROBE_ALLEN_KEY_DEPLOY_4_Z Z_PROBE_ALLEN_KEY_DEPLOY_3_Z
#define Z_PROBE_ALLEN_KEY_DEPLOY_4_FEEDRATE XY_PROBE_SPEED
#define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip
#define Z_PROBE_ALLEN_KEY_STOW_1_Y -122.00 #define Z_PROBE_ALLEN_KEY_STOW_1_Y -122.00
#define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0 #define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0
@ -910,11 +927,9 @@
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
#endif #endif
// Delta only homes to Z // Delta only homes to Z
#define HOMING_FEEDRATE_Z (200*30) #define HOMING_FEEDRATE_Z (200*30)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

47
Marlin/example_configurations/delta/generic/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -904,11 +921,9 @@
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
#endif #endif
// Delta only homes to Z // Delta only homes to Z
#define HOMING_FEEDRATE_Z (200*60) #define HOMING_FEEDRATE_Z (200*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

47
Marlin/example_configurations/delta/kossel_mini/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -907,11 +924,9 @@
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
#endif #endif
// Delta only homes to Z // Delta only homes to Z
#define HOMING_FEEDRATE_Z (200*60) #define HOMING_FEEDRATE_Z (200*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

1
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
Unescape View File

@ -364,6 +364,7 @@
#define DEFAULT_MINSEGMENTTIME 20000 #define DEFAULT_MINSEGMENTTIME 20000
// If defined the movements slow down when the look ahead buffer is only half full // If defined the movements slow down when the look ahead buffer is only half full
// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second)
//#define SLOWDOWN //#define SLOWDOWN
// Frequency limit // Frequency limit

54
Marlin/example_configurations/delta/kossel_pro/Configuration.h
Unescape View File

@ -94,8 +94,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -111,15 +111,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 115200 #define BAUDRATE 115200
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -175,14 +184,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -617,10 +634,10 @@
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin #define Z_PROBE_ALLEN_KEY_DEPLOY_4_X 45.00 // Move right to trigger deploy pin
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 #define Z_PROBE_ALLEN_KEY_DEPLOY_4_Y -125.00
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z #define Z_PROBE_ALLEN_KEY_DEPLOY_4_Z Z_PROBE_ALLEN_KEY_DEPLOY_3_Z
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (XY_PROBE_SPEED)/2 #define Z_PROBE_ALLEN_KEY_DEPLOY_4_FEEDRATE (XY_PROBE_SPEED)/2
#define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip
#define Z_PROBE_ALLEN_KEY_STOW_1_Y -125.00 #define Z_PROBE_ALLEN_KEY_STOW_1_Y -125.00
@ -908,7 +925,6 @@
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
#endif #endif
// Delta only homes to Z // Delta only homes to Z
#define HOMING_FEEDRATE_Z (200*60) #define HOMING_FEEDRATE_Z (200*60)

1
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
Unescape View File

@ -369,6 +369,7 @@
#define DEFAULT_MINSEGMENTTIME 20000 #define DEFAULT_MINSEGMENTTIME 20000
// If defined the movements slow down when the look ahead buffer is only half full // If defined the movements slow down when the look ahead buffer is only half full
// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second)
//#define SLOWDOWN //#define SLOWDOWN
// Frequency limit // Frequency limit

46
Marlin/example_configurations/delta/kossel_xl/Configuration.h
Unescape View File

@ -81,8 +81,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(oxivanisher)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(oxivanisher)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -98,15 +98,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -162,14 +171,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 2 #define POWER_SUPPLY 2
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -913,7 +930,6 @@
// Delta only homes to Z // Delta only homes to Z
#define HOMING_FEEDRATE_Z (60*60) #define HOMING_FEEDRATE_Z (60*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/makibox/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -825,7 +842,6 @@
#define HOMING_FEEDRATE_XY 1500 #define HOMING_FEEDRATE_XY 1500
#define HOMING_FEEDRATE_Z (2*60) #define HOMING_FEEDRATE_Z (2*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

46
Marlin/example_configurations/tvrrug/Round2/Configuration.h
Unescape View File

@ -88,8 +88,8 @@
// build by the user have been successfully uploaded into firmware. // build by the user have been successfully uploaded into firmware.
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
#define SHOW_BOOTSCREEN #define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during boot in line 1 #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during boot in line 2 #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
// //
// *** VENDORS PLEASE READ ***************************************************** // *** VENDORS PLEASE READ *****************************************************
@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
* 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 1 #define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -818,7 +835,6 @@
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (4*60)
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
//============================================================================= //=============================================================================

Write Preview
Loading…
Cancel
Save