Rename BEEPER to BEEPER_PIN

For consistency with other pins, allowing use of `PIN_EXISTS` macro.
master
Scott Lahteine 9 years ago committed by Richard Wackerbarth
parent b217474eab
commit 94a796c8cc

@ -512,7 +512,7 @@
#define WRITE_FAN(v) WRITE(FAN_PIN, v) #define WRITE_FAN(v) WRITE(FAN_PIN, v)
#endif #endif
#define HAS_BUZZER ((defined(BEEPER) && BEEPER >= 0) || defined(LCD_USE_I2C_BUZZER)) #define HAS_BUZZER (PIN_EXISTS(BEEPER) || defined(LCD_USE_I2C_BUZZER))
#if defined(NUM_SERVOS) && NUM_SERVOS > 0 #if defined(NUM_SERVOS) && NUM_SERVOS > 0
#ifndef X_ENDSTOP_SERVO_NR #ifndef X_ENDSTOP_SERVO_NR

@ -7,22 +7,22 @@
if (freq > 0) { if (freq > 0) {
#if ENABLED(LCD_USE_I2C_BUZZER) #if ENABLED(LCD_USE_I2C_BUZZER)
lcd_buzz(duration, freq); lcd_buzz(duration, freq);
#elif defined(BEEPER) && BEEPER >= 0 // on-board buzzers have no further condition #elif PIN_EXISTS(BEEPER) // on-board buzzers have no further condition
SET_OUTPUT(BEEPER); SET_OUTPUT(BEEPER_PIN);
#ifdef SPEAKER // a speaker needs a AC ore a pulsed DC #ifdef SPEAKER // a speaker needs a AC ore a pulsed DC
//tone(BEEPER, freq, duration); // needs a PWMable pin //tone(BEEPER_PIN, freq, duration); // needs a PWMable pin
unsigned int delay = 1000000 / freq / 2; unsigned int delay = 1000000 / freq / 2;
int i = duration * freq / 1000; int i = duration * freq / 1000;
while (i--) { while (i--) {
WRITE(BEEPER,HIGH); WRITE(BEEPER_PIN, HIGH);
delayMicroseconds(delay); delayMicroseconds(delay);
WRITE(BEEPER,LOW); WRITE(BEEPER_PIN, LOW);
delayMicroseconds(delay); delayMicroseconds(delay);
} }
#else // buzzer has its own resonator - needs a DC #else // buzzer has its own resonator - needs a DC
WRITE(BEEPER, HIGH); WRITE(BEEPER_PIN, HIGH);
delay(duration); delay(duration);
WRITE(BEEPER, LOW); WRITE(BEEPER_PIN, LOW);
#endif #endif
#else #else
delay(duration); delay(duration);

@ -30,8 +30,8 @@
#define HEATER_BED_PIN 9 // BED #define HEATER_BED_PIN 9 // BED
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#undef BEEPER #undef BEEPER_PIN
#define BEEPER -1 #define BEEPER_PIN -1
#undef LCD_PINS_RS #undef LCD_PINS_RS
#undef LCD_PINS_ENABLE #undef LCD_PINS_ENABLE
@ -56,6 +56,6 @@
#else #else
#define BEEPER 33 #define BEEPER_PIN 33
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL

@ -8,7 +8,8 @@
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 33 #define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 31 #define DOGLCD_A0 31
#define DOGLCD_CS 32 #define DOGLCD_CS 32

@ -6,7 +6,7 @@
#undef FAN_PIN #undef FAN_PIN
#define FAN_PIN 6 //Part Cooling System #define FAN_PIN 6 //Part Cooling System
#define BEEPER 33 #define BEEPER_PIN 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable) #define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side. //Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5 #define EXTRUDER_0_AUTO_FAN_PIN 5
@ -97,7 +97,7 @@
//LCD Pins// //LCD Pins//
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 33 #define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44 #define DOGLCD_A0 44
#define DOGLCD_CS 45 #define DOGLCD_CS 45

@ -53,7 +53,7 @@
#define TEMP_2_PIN 1 //ANALOG NUMBERING #define TEMP_2_PIN 1 //ANALOG NUMBERING
#define TEMP_BED_PIN 0 //ANALOG NUMBERING #define TEMP_BED_PIN 0 //ANALOG NUMBERING
#define BEEPER 36 #define BEEPER_PIN 36
#define KILL_PIN -1 #define KILL_PIN -1

@ -56,7 +56,7 @@
//#define TX_ENABLE_PIN 12 //#define TX_ENABLE_PIN 12
//#define RX_ENABLE_PIN 13 //#define RX_ENABLE_PIN 13
#define BEEPER -1 #define BEEPER_PIN -1
#define SDCARDDETECT -1 #define SDCARDDETECT -1
#define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work #define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work

@ -89,7 +89,7 @@
#endif #endif
#ifdef MINIPANEL #ifdef MINIPANEL
#define BEEPER 46 #define BEEPER_PIN 46
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 47 #define DOGLCD_A0 47
#define DOGLCD_CS 45 #define DOGLCD_CS 45

@ -58,7 +58,7 @@
#define HEATER_BED_PIN 10 // BED #define HEATER_BED_PIN 10 // BED
#define TEMP_BED_PIN 14 // ANALOG NUMBERING #define TEMP_BED_PIN 14 // ANALOG NUMBERING
#define BEEPER 33 // AUX-4 #define BEEPER_PIN 33 // AUX-4
#if defined(ULTRA_LCD) && defined(NEWPANEL) #if defined(ULTRA_LCD) && defined(NEWPANEL)

@ -74,7 +74,7 @@
#define TEMP_BED_PIN 14 // ANALOG NUMBERING #define TEMP_BED_PIN 14 // ANALOG NUMBERING
#endif #endif
#define BEEPER 64 #define BEEPER_PIN 64
#define LCD_PINS_RS 14 #define LCD_PINS_RS 14

@ -76,7 +76,7 @@
#define TEMP_2_PIN (TEMP_SENSOR_2 == -1 ? 9 : 12) // ANALOG NUMBERING #define TEMP_2_PIN (TEMP_SENSOR_2 == -1 ? 9 : 12) // ANALOG NUMBERING
#define TEMP_BED_PIN (TEMP_SENSOR_BED == -1 ? 8 : 14) // ANALOG NUMBERING #define TEMP_BED_PIN (TEMP_SENSOR_BED == -1 ? 8 : 14) // ANALOG NUMBERING
#define BEEPER 61 #define BEEPER_PIN 61
#define LCD_PINS_RS 32 #define LCD_PINS_RS 32
#define LCD_PINS_ENABLE 31 #define LCD_PINS_ENABLE 31

@ -91,8 +91,8 @@
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)
#define KILL_PIN 32 #define KILL_PIN 32
#if ENABLED(NEWPANEL) #if ENABLED(NEWPANEL)
//arduino pin which triggers an piezzo beeper
#define BEEPER 84 // Beeper on AUX-4 #define BEEPER_PIN 84 // Beeper on AUX-4
#define LCD_PINS_RS 82 #define LCD_PINS_RS 82
#define LCD_PINS_ENABLE 18 #define LCD_PINS_ENABLE 18
#define LCD_PINS_D4 19 #define LCD_PINS_D4 19

@ -59,8 +59,7 @@
#define HEATER_BED_PIN 3 // BED #define HEATER_BED_PIN 3 // BED
#define TEMP_BED_PIN 6 // ANALOG NUMBERING #define TEMP_BED_PIN 6 // ANALOG NUMBERING
#define BEEPER -1 #define BEEPER_PIN -1
#define LCD_PINS_RS -1 #define LCD_PINS_RS -1
#define LCD_PINS_ENABLE -1 #define LCD_PINS_ENABLE -1

@ -79,7 +79,7 @@
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
//we have no buzzer installed //we have no buzzer installed
#define BEEPER -1 #define BEEPER_PIN -1
//LCD Pins //LCD Pins
#if ENABLED(LCD_I2C_PANELOLU2) #if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27 #define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
@ -92,7 +92,7 @@
#endif // ULTRA_LCD && NEWPANEL #endif // ULTRA_LCD && NEWPANEL
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 32 //FastIO #define BEEPER_PIN 32 //FastIO
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 42 //Non-FastIO #define DOGLCD_A0 42 //Non-FastIO
#define DOGLCD_CS 43 //Non-FastIO #define DOGLCD_CS 43 //Non-FastIO

@ -112,8 +112,9 @@
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)
#define KILL_PIN 80 #define KILL_PIN 80
#if ENABLED(NEWPANEL) #if ENABLED(NEWPANEL)
//arduino pin which triggers an piezzo beeper
#define BEEPER 79 // Beeper on AUX-4 #define BEEPER_PIN 79 // Beeper on AUX-4
#define LCD_PINS_RS 70 #define LCD_PINS_RS 70
#define LCD_PINS_ENABLE 71 #define LCD_PINS_ENABLE 71
#define LCD_PINS_D4 72 #define LCD_PINS_D4 72
@ -133,8 +134,9 @@
#define SDCARDDETECT 81 // Ramps does not use this port #define SDCARDDETECT 81 // Ramps does not use this port
#else //!NEWPANEL - old style panel with shift register #else //!NEWPANEL - old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 33 No Beeper added #define BEEPER_PIN 33 // No Beeper added
//buttons are attached to a shift register //buttons are attached to a shift register
// Not wired this yet // Not wired this yet
// #define SHIFT_CLK 38 // #define SHIFT_CLK 38
@ -165,7 +167,7 @@
#endif // ULTRA_LCD #endif // ULTRA_LCD
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 44 #define BEEPER_PIN 44
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 70 #define DOGLCD_A0 70
#define DOGLCD_CS 71 #define DOGLCD_CS 71

@ -159,7 +159,7 @@
#endif #endif
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BEEPER 37 #define BEEPER_PIN 37
#define BTN_EN1 31 #define BTN_EN1 31
#define BTN_EN2 33 #define BTN_EN2 33
@ -186,12 +186,12 @@
#define SDCARDDETECT 49 #define SDCARDDETECT 49
#define LCD_SDSS 53 #define LCD_SDSS 53
#define KILL_PIN 41 #define KILL_PIN 41
#define BEEPER 23 #define BEEPER_PIN 23
#define DOGLCD_CS 29 #define DOGLCD_CS 29
#define DOGLCD_A0 27 #define DOGLCD_A0 27
#define LCD_PIN_BL 33 #define LCD_PIN_BL 33
#elif defined(MINIPANEL) #elif defined(MINIPANEL)
#define BEEPER 42 #define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44 #define DOGLCD_A0 44
#define DOGLCD_CS 66 #define DOGLCD_CS 66
@ -211,9 +211,10 @@
#define BTN_ENC 59 //the click switch #define BTN_ENC 59 //the click switch
//not connected to a pin //not connected to a pin
#define SDCARDDETECT 49 #define SDCARDDETECT 49
#else #else
// arduino pin which triggers an piezzo beeper
#define BEEPER 33 // Beeper on AUX-4 #define BEEPER_PIN 33 // Beeper on AUX-4
// buttons are directly attached using AUX-2 // buttons are directly attached using AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD) #if ENABLED(REPRAPWORLD_KEYPAD)
@ -241,8 +242,8 @@
#endif #endif
#else // !NEWPANEL (Old-style panel with shift register) #else // !NEWPANEL (Old-style panel with shift register)
// Arduino pin to trigger a piezzo beeper
#define BEEPER 33 // No Beeper added #define BEEPER_PIN 33 // No Beeper added
// Buttons are attached to a shift register // Buttons are attached to a shift register
// Not wired yet // Not wired yet

@ -22,8 +22,8 @@
#if ENABLED(RIGIDBOT_PANEL) #if ENABLED(RIGIDBOT_PANEL)
#undef BEEPER #undef BEEPER_PIN
#define BEEPER -1 #define BEEPER_PIN -1
#undef SDCARDDETECT #undef SDCARDDETECT
#define SDCARDDETECT 22 #define SDCARDDETECT 22
@ -48,8 +48,8 @@
#elif defined(REPRAP_DISCOUNT_SMART_CONTROLLER) #elif defined(REPRAP_DISCOUNT_SMART_CONTROLLER)
#undef BEEPER #undef BEEPER_PIN
#define BEEPER -1 #define BEEPER_PIN -1
#undef SDCARDDETECT #undef SDCARDDETECT
#define SDCARDDETECT 22 #define SDCARDDETECT 22

@ -102,7 +102,7 @@
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 53 #define SDSS 53
#define SDCARDDETECT 49 #define SDCARDDETECT 49
#define BEEPER 44 #define BEEPER_PIN 44
#define LCD_PINS_RS 19 #define LCD_PINS_RS 19
#define LCD_PINS_ENABLE 42 #define LCD_PINS_ENABLE 42
#define LCD_PINS_D4 18 #define LCD_PINS_D4 18

@ -95,7 +95,7 @@
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
// No buzzer installed // No buzzer installed
#define BEEPER -1 #define BEEPER_PIN -1
// LCD Pins // LCD Pins
#if ENABLED(DOGLCD) #if ENABLED(DOGLCD)
@ -106,7 +106,7 @@
#define LCD_PINS_RS 30 //CS chip select /SS chip slave select #define LCD_PINS_RS 30 //CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 29 //SID (MOSI) #define LCD_PINS_ENABLE 29 //SID (MOSI)
#define LCD_PINS_D4 17 //SCK (CLK) clock #define LCD_PINS_D4 17 //SCK (CLK) clock
#define BEEPER 27 // Pin 27 is take by LED_Pin, but Melzi LED do nothing with Marlin and I take this pin for BEEPER.... See here > [github.com] , If you want use this pin with Gcode M42 instead BEEPER #define BEEPER_PIN 27 // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with Marlin so this can be used for BEEPER_PIN. You can use this pin with M42 instead of BEEPER_PIN.
#else // Sanguinololu 1.3 #else // Sanguinololu 1.3
#define LCD_PINS_RS 4 #define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17 #define LCD_PINS_ENABLE 17
@ -160,7 +160,7 @@
#elif ENABLED(MAKRPANEL) #elif ENABLED(MAKRPANEL)
#define BEEPER 29 #define BEEPER_PIN 29
// Pins for DOGM SPI LCD Support // Pins for DOGM SPI LCD Support
#define DOGLCD_A0 30 #define DOGLCD_A0 30

@ -85,7 +85,7 @@
#define ALARM_PIN -1 #define ALARM_PIN -1
#define SDCARDDETECT -1 #define SDCARDDETECT -1
#define BEEPER -1 #define BEEPER_PIN -1
#define LCD_PINS_RS -1 #define LCD_PINS_RS -1
#define LCD_PINS_ENABLE -1 #define LCD_PINS_ENABLE -1
#define LCD_PINS_D4 -1 #define LCD_PINS_D4 -1

@ -68,9 +68,10 @@
#endif #endif
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
//we have no buzzer installed
#define BEEPER -1
//LCD Pins //LCD Pins
#define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2) #if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27 #define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
#define BTN_EN2 26 //TX1 - fastio.h pin mapping 26 #define BTN_EN2 26 //TX1 - fastio.h pin mapping 26

@ -58,8 +58,7 @@
#define MOTOR_CURRENT_PWM_RANGE 2000 #define MOTOR_CURRENT_PWM_RANGE 2000
#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250} #define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}
//arduino pin witch triggers an piezzo beeper #define BEEPER_PIN 18
#define BEEPER 18
#define LCD_PINS_RS 20 #define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 15 #define LCD_PINS_ENABLE 15

@ -57,9 +57,9 @@
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)
#define BEEPER_PIN 18
#if ENABLED(NEWPANEL) #if ENABLED(NEWPANEL)
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#define LCD_PINS_RS 20 #define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17 #define LCD_PINS_ENABLE 17
@ -71,15 +71,12 @@
//buttons are directly attached //buttons are directly attached
#define BTN_EN1 40 #define BTN_EN1 40
#define BTN_EN2 42 #define BTN_EN2 42
#define BTN_ENC 19 //the click #define BTN_ENC 19
#define SDCARDDETECT 38 #define SDCARDDETECT 38
#else //!NEWPANEL - Old style panel with shift register #else //!NEWPANEL - Old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
//buttons are attached to a shift register //buttons are attached to a shift register
#define SHIFT_CLK 38 #define SHIFT_CLK 38
#define SHIFT_LD 42 #define SHIFT_LD 42

@ -1325,7 +1325,7 @@ void lcd_quick_feedback() {
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS (1000/6) #define LCD_FEEDBACK_FREQUENCY_DURATION_MS (1000/6)
#endif #endif
lcd.buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); lcd.buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
#elif defined(BEEPER) && BEEPER >= 0 #elif PIN_EXISTS(BEEPER)
#ifndef LCD_FEEDBACK_FREQUENCY_HZ #ifndef LCD_FEEDBACK_FREQUENCY_HZ
#define LCD_FEEDBACK_FREQUENCY_HZ 5000 #define LCD_FEEDBACK_FREQUENCY_HZ 5000
#endif #endif

Loading…
Cancel
Save