forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Merge pull request #6266 from thinkyhead/rc_cleanup_after

Browse Source 
Cleanup after recent merges
master
Scott Lahteine 8 years ago committed by GitHub
parent 34d3ed9ab1 d4ce839351
commit 98c9de11e1
34 changed files with 809 additions and 699 deletions
Show Stats Download Patch File Download Diff File

56
Marlin/Configuration.h
Unescape View File

@ -596,7 +596,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -623,16 +623,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1547,33 +1547,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

73
Marlin/Marlin_main.cpp
Unescape View File

@ -1777,7 +1777,6 @@ static void clean_up_after_endstop_or_probe_move() {
lcd_status_printf_P(0, PSTR(MSG_HOME " %s%s%s " MSG_FIRST), xx ? MSG_X : "", yy ? MSG_Y : "", zz ? MSG_Z : ""); lcd_status_printf_P(0, PSTR(MSG_HOME " %s%s%s " MSG_FIRST), xx ? MSG_X : "", yy ? MSG_Y : "", zz ? MSG_Z : "");
#endif #endif
return true; return true;
} }
return false; return false;
} }
@ -1983,7 +1982,6 @@ static void clean_up_after_endstop_or_probe_move() {
#endif #endif
#endif #endif
#if ENABLED(BLTOUCH) #if ENABLED(BLTOUCH)
void bltouch_command(int angle) { void bltouch_command(int angle) {
servo[Z_ENDSTOP_SERVO_NR].move(angle); // Give the BL-Touch the command and wait servo[Z_ENDSTOP_SERVO_NR].move(angle); // Give the BL-Touch the command and wait
@ -2206,8 +2204,7 @@ static void clean_up_after_endstop_or_probe_move() {
// - Raise to the BETWEEN height // - Raise to the BETWEEN height
// - Return the probed Z position // - Return the probed Z position
// //
//float probe_pt(const float &x, const float &y, const bool stow = true, const int verbose_level = 1) { float probe_pt(const float x, const float y, const bool stow/*=true*/, const int verbose_level/*=1*/) {
float probe_pt(const float x, const float y, const bool stow, const int verbose_level) {
#if ENABLED(DEBUG_LEVELING_FEATURE) #if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) { if (DEBUGGING(LEVELING)) {
SERIAL_ECHOPAIR(">>> probe_pt(", x); SERIAL_ECHOPAIR(">>> probe_pt(", x);
@ -5319,27 +5316,18 @@ inline void gcode_M42() {
#include "pinsDebug.h" #include "pinsDebug.h"
inline void toggle_pins() { inline void toggle_pins() {
int pin, j, start = 0, I_flag = 0, end = NUM_DIGITAL_PINS - 1, wait = 500, repeat = 1; int pin, j;
if (code_seen('R'))
repeat = code_value_int();
if (code_seen('S')) bool I_flag = code_seen('I') ? code_value_bool() : false;
start = code_value_int();
if (code_seen('E'))
end = code_value_int();
if (code_seen('I') ) int repeat = code_seen('R') ? code_value_int() : 1,
I_flag++; start = code_seen('S') ? code_value_int() : 0,
end = code_seen('E') ? code_value_int() : NUM_DIGITAL_PINS - 1,
wait = code_seen('W') ? code_value_int() : 500;
if (code_seen('W')) for (pin = start; pin <= end; pin++) {
wait = code_value_int(); if (!I_flag && pin_is_protected(pin)) {
for(pin = start; pin <= end; pin++) {
if ( I_flag == 0 && pin_is_protected(pin)) {
SERIAL_ECHOPAIR("Sensitive Pin: ", pin); SERIAL_ECHOPAIR("Sensitive Pin: ", pin);
SERIAL_ECHOPGM(" untouched.\n"); SERIAL_ECHOPGM(" untouched.\n");
} }
@ -5348,22 +5336,17 @@ inline void gcode_M42() {
pinMode(pin, OUTPUT); pinMode(pin, OUTPUT);
for(j = 0; j < repeat; j++) { for(j = 0; j < repeat; j++) {
digitalWrite(pin, 0); digitalWrite(pin, 0);
idle(); safe_delay(wait);
delay(wait);
digitalWrite(pin, 1); digitalWrite(pin, 1);
idle(); safe_delay(wait);
delay(wait);
digitalWrite(pin, 0); digitalWrite(pin, 0);
idle(); safe_delay(wait);
delay(wait);
} }
} }
SERIAL_ECHOPGM("\n"); SERIAL_ECHOPGM("\n");
} }
SERIAL_ECHOPGM("Done\n"); SERIAL_ECHOPGM("Done\n");
return; } // toggle_pins
} // toggle pin(s)
inline void servo_probe_test(){ inline void servo_probe_test(){
#if !(NUM_SERVOS >= 1 && HAS_SERVO_0) #if !(NUM_SERVOS >= 1 && HAS_SERVO_0)
@ -5481,7 +5464,6 @@ inline void gcode_M42() {
* M43 S - Servo probe test * M43 S - Servo probe test
* P<index> - Probe index (optional - defaults to 0 * P<index> - Probe index (optional - defaults to 0
*/ */
inline void gcode_M43() { inline void gcode_M43() {
if (code_seen('T')) { // must be first ot else it's "S" and "E" parameters will execute endstop or servo test if (code_seen('T')) { // must be first ot else it's "S" and "E" parameters will execute endstop or servo test
@ -5503,7 +5485,6 @@ inline void gcode_M42() {
return; return;
} }
// Get the range of pins to test or watch // Get the range of pins to test or watch
int first_pin = 0, last_pin = NUM_DIGITAL_PINS - 1; int first_pin = 0, last_pin = NUM_DIGITAL_PINS - 1;
if (code_seen('P')) { if (code_seen('P')) {
@ -5511,10 +5492,10 @@ inline void gcode_M42() {
if (first_pin > NUM_DIGITAL_PINS - 1) return; if (first_pin > NUM_DIGITAL_PINS - 1) return;
} }
bool ignore_protection = code_seen('I'); bool ignore_protection = code_seen('I') ? code_value_bool() : false;
// Watch until click, M108, or reset // Watch until click, M108, or reset
if (code_seen('W')) { // watch digital pins if (code_seen('W') && code_value_bool()) { // watch digital pins
SERIAL_PROTOCOLLNPGM("Watching pins"); SERIAL_PROTOCOLLNPGM("Watching pins");
byte pin_state[last_pin - first_pin + 1]; byte pin_state[last_pin - first_pin + 1];
for (int8_t pin = first_pin; pin <= last_pin; pin++) { for (int8_t pin = first_pin; pin <= last_pin; pin++) {
@ -5558,7 +5539,6 @@ inline void gcode_M42() {
report_pin_state_extended(pin, ignore_protection); report_pin_state_extended(pin, ignore_protection);
} }
#endif // PINS_DEBUGGING #endif // PINS_DEBUGGING
#if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
@ -6041,17 +6021,18 @@ inline void gcode_M105() {
#endif #endif
#ifndef MIN_COOLING_SLOPE_DEG
#define MIN_COOLING_SLOPE_DEG 1.50
#endif
#ifndef MIN_COOLING_SLOPE_TIME
#define MIN_COOLING_SLOPE_TIME 60
#endif
/** /**
* M109: Sxxx Wait for extruder(s) to reach temperature. Waits only when heating. * M109: Sxxx Wait for extruder(s) to reach temperature. Waits only when heating.
* Rxxx Wait for extruder(s) to reach temperature. Waits when heating and cooling. * Rxxx Wait for extruder(s) to reach temperature. Waits when heating and cooling.
*/ */
#ifndef MIN_COOLING_SLOPE_DEG
#define MIN_COOLING_SLOPE_DEG 1.50
#endif
#ifndef MIN_COOLING_SLOPE_TIME
#define MIN_COOLING_SLOPE_TIME 60
#endif
inline void gcode_M109() { inline void gcode_M109() {
if (get_target_extruder_from_command(109)) return; if (get_target_extruder_from_command(109)) return;
@ -6275,11 +6256,11 @@ inline void gcode_M109() {
residency_start_ms = now; residency_start_ms = now;
} }
#endif //TEMP_BED_RESIDENCY_TIME > 0 #endif // TEMP_BED_RESIDENCY_TIME > 0
// Prevent a wait-forever situation if R is misused i.e. M190 R0 // Prevent a wait-forever situation if R is misused i.e. M190 R0
if (wants_to_cool) { if (wants_to_cool) {
// break after MIN_COOLING_SLOPE_TIME_BED seconds // Break after MIN_COOLING_SLOPE_TIME_BED seconds
// if the temperature did not drop at least MIN_COOLING_SLOPE_DEG_BED // if the temperature did not drop at least MIN_COOLING_SLOPE_DEG_BED
if (!next_cool_check_ms || ELAPSED(now, next_cool_check_ms)) { if (!next_cool_check_ms || ELAPSED(now, next_cool_check_ms)) {
if (old_temp - temp < MIN_COOLING_SLOPE_DEG_BED) break; if (old_temp - temp < MIN_COOLING_SLOPE_DEG_BED) break;
@ -6307,7 +6288,7 @@ inline void gcode_M110() {
* M111: Set the debug level * M111: Set the debug level
*/ */
inline void gcode_M111() { inline void gcode_M111() {
marlin_debug_flags = code_seen('S') ? code_value_byte() : (uint8_t) DEBUG_NONE; marlin_debug_flags = code_seen('S') ? code_value_byte() : (uint8_t)DEBUG_NONE;
const static char str_debug_1[] PROGMEM = MSG_DEBUG_ECHO; const static char str_debug_1[] PROGMEM = MSG_DEBUG_ECHO;
const static char str_debug_2[] PROGMEM = MSG_DEBUG_INFO; const static char str_debug_2[] PROGMEM = MSG_DEBUG_INFO;
@ -6463,7 +6444,6 @@ inline void gcode_M140() {
#if ENABLED(ULTIPANEL) #if ENABLED(ULTIPANEL)
powersupply = true; powersupply = true;
LCD_MESSAGEPGM(WELCOME_MSG); LCD_MESSAGEPGM(WELCOME_MSG);
lcd_update();
#endif #endif
} }
@ -6496,7 +6476,6 @@ inline void gcode_M81() {
powersupply = false; powersupply = false;
#endif #endif
LCD_MESSAGEPGM(MACHINE_NAME " " MSG_OFF "."); LCD_MESSAGEPGM(MACHINE_NAME " " MSG_OFF ".");
lcd_update();
#endif #endif
} }

56
Marlin/example_configurations/Cartesio/Configuration.h
Unescape View File

@ -595,7 +595,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -622,16 +622,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1546,33 +1546,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/Felix/Configuration.h
Unescape View File

@ -579,7 +579,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -606,16 +606,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1530,33 +1530,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/Felix/DUAL/Configuration.h
Unescape View File

@ -579,7 +579,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -606,16 +606,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1530,33 +1530,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/Hephestos/Configuration.h
Unescape View File

@ -587,7 +587,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -614,16 +614,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1538,33 +1538,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/Hephestos_2/Configuration.h
Unescape View File

@ -590,7 +590,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -617,16 +617,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1541,33 +1541,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 2.00 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.60 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.60 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/K8200/Configuration.h
Unescape View File

@ -625,7 +625,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -652,16 +652,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1580,33 +1580,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/K8400/Configuration.h
Unescape View File

@ -596,7 +596,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -623,16 +623,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1547,33 +1547,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/K8400/Dual-head/Configuration.h
Unescape View File

@ -596,7 +596,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -623,16 +623,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1547,33 +1547,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
Unescape View File

@ -596,7 +596,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -623,16 +623,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1547,33 +1547,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/RigidBot/Configuration.h
Unescape View File

@ -595,7 +595,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -622,16 +622,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1548,33 +1548,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/SCARA/Configuration.h
Unescape View File

@ -611,7 +611,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -638,16 +638,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1562,33 +1562,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/TAZ4/Configuration.h
Unescape View File

@ -616,7 +616,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -643,16 +643,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1567,33 +1567,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/TinyBoy2/Configuration.h
Unescape View File

@ -647,7 +647,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -674,16 +674,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1598,33 +1598,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/WITBOX/Configuration.h
Unescape View File

@ -587,7 +587,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -614,16 +614,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1538,33 +1538,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/adafruit/ST7565/Configuration.h
Unescape View File

@ -596,7 +596,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -623,16 +623,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1547,33 +1547,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h
Unescape View File

@ -654,7 +654,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -681,16 +681,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 2000 #define XY_PROBE_SPEED 2000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
#define PROBE_DOUBLE_TOUCH #define PROBE_DOUBLE_TOUCH
/** /**
@ -1654,33 +1654,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/delta/generic/Configuration.h
Unescape View File

@ -641,7 +641,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -668,16 +668,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 4000 #define XY_PROBE_SPEED 4000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
@ -1638,33 +1638,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/delta/kossel_mini/Configuration.h
Unescape View File

@ -634,7 +634,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -661,16 +661,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 4000 #define XY_PROBE_SPEED 4000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1634,33 +1634,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/delta/kossel_pro/Configuration.h
Unescape View File

@ -635,7 +635,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -665,16 +665,16 @@
* not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed. * not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed.
*/ */
#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero). #define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero).
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1641,33 +1641,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/delta/kossel_xl/Configuration.h
Unescape View File

@ -654,7 +654,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -681,16 +681,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!) #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!)
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1649,33 +1649,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/makibox/Configuration.h
Unescape View File

@ -599,7 +599,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -626,16 +626,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1550,33 +1550,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

56
Marlin/example_configurations/tvrrug/Round2/Configuration.h
Unescape View File

@ -592,7 +592,7 @@
* is enabled then it also applies to Z_PROBE_SPEED_SLOW. * is enabled then it also applies to Z_PROBE_SPEED_SLOW.
*/ */
/* Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. */ // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED //#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -619,16 +619,16 @@
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
/* X and Y axis travel speed (mm/m) between probes */ // X and Y axis travel speed (mm/m) between probes
#define XY_PROBE_SPEED 8000 #define XY_PROBE_SPEED 8000
/* Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) */ // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
/* Speed for the "accurate" probe of each point */ // Speed for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
/* Use double touch for probing */ // Use double touch for probing
//#define PROBE_DOUBLE_TOUCH //#define PROBE_DOUBLE_TOUCH
/** /**
@ -1543,33 +1543,39 @@
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
/**********************************************************************\ /**
* Support for a filament diameter sensor * Filament Width Sensor
* Also allows adjustment of diameter at print time (vs at slicing) *
* Single extruder only at this point (extruder 0) * Measures the filament width in real-time and adjusts
* * flow rate to compensate for any irregularities.
* Motherboards *
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector * Also allows the measured filament diameter to set the
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) * extrusion rate, so the slicer only has to specify the
* 301 - Rambo - uses Analog input 3 * volume.
* Note may require analog pins to be defined for different motherboards *
**********************************************************************/ * Only a single extruder is supported at this time.
// Uncomment below to enable *
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
* 301 RAMBO : Analog input 3
*
* Note: May require analog pins to be defined for other boards.
*/
//#define FILAMENT_WIDTH_SENSOR //#define FILAMENT_WIDTH_SENSOR
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
//#define FILAMENT_LCD_DISPLAY //#define FILAMENT_LCD_DISPLAY
#endif #endif

2
Marlin/nozzle.h
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

3
Marlin/pins.h
Unescape View File

@ -303,6 +303,9 @@
#if !defined(E3_AUTO_FAN_PIN) && defined(ORIG_E3_AUTO_FAN_PIN) #if !defined(E3_AUTO_FAN_PIN) && defined(ORIG_E3_AUTO_FAN_PIN)
#define E3_AUTO_FAN_PIN ORIG_E3_AUTO_FAN_PIN #define E3_AUTO_FAN_PIN ORIG_E3_AUTO_FAN_PIN
#endif #endif
#if !defined(E4_AUTO_FAN_PIN) && defined(ORIG_E4_AUTO_FAN_PIN)
#define E4_AUTO_FAN_PIN ORIG_E4_AUTO_FAN_PIN
#endif
// List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! // List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, E0_MS1_PIN, E0_MS2_PIN, #define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, E0_MS1_PIN, E0_MS2_PIN,

89
Marlin/pinsDebug.h
Unescape View File

@ -80,7 +80,7 @@ bool endstop_monitor_flag = false;
const char* const pin_array[][3] PROGMEM = { const char* const pin_array[][3] PROGMEM = {
/** /**
* [pin name] [pin number] [is digital or analog] 1 = digital, 0 = analog * [pin name] [pin number] [is digital or analog] 1 = digital, 0 = analog
* Each entry takes up 6 bytes in FLASH: * Each entry takes up 6 bytes in FLASH:
* 2 byte pointer to location of the name string * 2 byte pointer to location of the name string
@ -109,7 +109,8 @@ const char* const pin_array[][3] PROGMEM = {
#define n_array (sizeof (pin_array) / sizeof (const char *))/3 #define n_array (sizeof (pin_array) / sizeof (const char *))/3
#if !defined(TIMER1B) // working with Teensyduino extension so need to re-define some things #ifndef TIMER1B
// working with Teensyduino extension so need to re-define some things
#include "pinsDebug_Teensyduino.h" #include "pinsDebug_Teensyduino.h"
#endif #endif
@ -132,7 +133,7 @@ static bool pwm_status(uint8_t pin) {
switch(digitalPinToTimer(pin)) { switch(digitalPinToTimer(pin)) {
#if defined(TCCR0A) && defined(COM0A1) #if defined(TCCR0A) && defined(COM0A1)
#if defined (TIMER0A) #ifdef TIMER0A
PWM_CASE(0,A); PWM_CASE(0,A);
#endif #endif
PWM_CASE(0,B); PWM_CASE(0,B);
@ -141,7 +142,7 @@ static bool pwm_status(uint8_t pin) {
#if defined(TCCR1A) && defined(COM1A1) #if defined(TCCR1A) && defined(COM1A1)
PWM_CASE(1,A); PWM_CASE(1,A);
PWM_CASE(1,B); PWM_CASE(1,B);
#if defined(COM1C1) && defined (TIMER1C) #if defined(COM1C1) && defined(TIMER1C)
PWM_CASE(1,C); PWM_CASE(1,C);
#endif #endif
#endif #endif
@ -200,13 +201,13 @@ const uint8_t* const PWM_other[][3] PROGMEM = {
const uint8_t* const PWM_OCR[][3] PROGMEM = { const uint8_t* const PWM_OCR[][3] PROGMEM = {
#if defined (TIMER0A) #ifdef TIMER0A
{&OCR0A,&OCR0B,0}, {&OCR0A,&OCR0B,0},
#else #else
{0,&OCR0B,0}, {0,&OCR0B,0},
#endif #endif
#if defined(COM1C1) && defined (TIMER1C) #if defined(COM1C1) && defined(TIMER1C)
{ (const uint8_t*) &OCR1A, (const uint8_t*) &OCR1B, (const uint8_t*) &OCR1C}, { (const uint8_t*) &OCR1A, (const uint8_t*) &OCR1B, (const uint8_t*) &OCR1C},
#else #else
{ (const uint8_t*) &OCR1A, (const uint8_t*) &OCR1B,0}, { (const uint8_t*) &OCR1A, (const uint8_t*) &OCR1B,0},
@ -217,7 +218,7 @@ const uint8_t* const PWM_OCR[][3] PROGMEM = {
#endif #endif
#if defined(TCCR3A) && defined(COM3A1) #if defined(TCCR3A) && defined(COM3A1)
#if defined(COM3C1) #ifdef COM3C1
{ (const uint8_t*) &OCR3A, (const uint8_t*) &OCR3B, (const uint8_t*) &OCR3C}, { (const uint8_t*) &OCR3A, (const uint8_t*) &OCR3B, (const uint8_t*) &OCR3C},
#else #else
{ (const uint8_t*) &OCR3A, (const uint8_t*) &OCR3B,0}, { (const uint8_t*) &OCR3A, (const uint8_t*) &OCR3B,0},
@ -279,10 +280,10 @@ void com_print(uint8_t N, uint8_t Z) {
} }
void timer_prefix(uint8_t T, char L, uint8_t N){ // T - timer L - pwm n - WGM bit layout void timer_prefix(uint8_t T, char L, uint8_t N) { // T - timer L - pwm n - WGM bit layout
char buffer[20]; // for the sprintf statements char buffer[20]; // for the sprintf statements
uint8_t *TCCRB = (uint8_t*) TCCR_B(T); uint8_t *TCCRB = (uint8_t*)TCCR_B(T);
uint8_t *TCCRA = (uint8_t*) TCCR_A(T); uint8_t *TCCRA = (uint8_t*)TCCR_A(T);
uint8_t WGM = (((*TCCRB & _BV(WGM_2)) >> 1) | (*TCCRA & (_BV(WGM_0) | _BV(WGM_1)))); uint8_t WGM = (((*TCCRB & _BV(WGM_2)) >> 1) | (*TCCRA & (_BV(WGM_0) | _BV(WGM_1))));
if (N == 4) WGM |= ((*TCCRB & _BV(WGM_3)) >> 1); if (N == 4) WGM |= ((*TCCRB & _BV(WGM_3)) >> 1);
@ -323,18 +324,15 @@ void timer_prefix(uint8_t T, char L, uint8_t N){ // T - timer L - pwm n - W
if (TEST(*TMSK, TOIE)) err_prob_interrupt(); if (TEST(*TMSK, TOIE)) err_prob_interrupt();
} }
static void pwm_details(uint8_t pin) { static void pwm_details(uint8_t pin) {
char buffer[20]; // for the sprintf statements char buffer[20]; // for the sprintf statements
uint8_t WGM; uint8_t WGM;
switch(digitalPinToTimer(pin)) { switch(digitalPinToTimer(pin)) {
#if defined(TCCR0A) && defined(COM0A1) #if defined(TCCR0A) && defined(COM0A1)
#if defined (TIMER0A) #ifdef TIMER0A
case TIMER0A: case TIMER0A:
timer_prefix(0,'A',3); timer_prefix(0,'A',3);
break; break;
@ -351,7 +349,7 @@ static void pwm_details(uint8_t pin) {
case TIMER1B: case TIMER1B:
timer_prefix(1,'B',4); timer_prefix(1,'B',4);
break; break;
#if defined(COM1C1) && defined (TIMER1C) #if defined(COM1C1) && defined(TIMER1C)
case TIMER1C: case TIMER1C:
timer_prefix(1,'C',4); timer_prefix(1,'C',4);
break; break;
@ -374,7 +372,7 @@ static void pwm_details(uint8_t pin) {
case TIMER3B: case TIMER3B:
timer_prefix(3,'B',4); timer_prefix(3,'B',4);
break; break;
#if defined(COM3C1) #ifdef COM3C1
case TIMER3C: case TIMER3C:
timer_prefix(3,'C',4); timer_prefix(3,'C',4);
break; break;
@ -410,17 +408,15 @@ static void pwm_details(uint8_t pin) {
} }
SERIAL_PROTOCOLPGM(" "); SERIAL_PROTOCOLPGM(" ");
// on pins that have two PWMs, print info on second PWM // on pins that have two PWMs, print info on second PWM
#if AVR_ATmega2560_FAMILY || AVR_AT90USB1286_FAMILY #if AVR_ATmega2560_FAMILY || AVR_AT90USB1286_FAMILY
// looking for port B7 - PWMs 0A and 1C // looking for port B7 - PWMs 0A and 1C
if ( ('B' == digitalPinToPort(pin) + 64) && (0x80 == digitalPinToBitMask(pin))) { if ( ('B' == digitalPinToPort(pin) + 64) && (0x80 == digitalPinToBitMask(pin))) {
#if !defined(TEENSYDUINO_IDE) #ifndef TEENSYDUINO_IDE
SERIAL_EOL; SERIAL_PROTOCOLPGM("\n . TIMER1C is also tied to this pin ");
SERIAL_PROTOCOLPGM (" . TIMER1C is also tied to this pin ");
timer_prefix(1,'C',4); timer_prefix(1,'C',4);
#else #else
SERIAL_EOL; SERIAL_PROTOCOLPGM("\n . TIMER0A is also tied to this pin ");
SERIAL_PROTOCOLPGM (" . TIMER0A is also tied to this pin ");
timer_prefix(0,'A',3); timer_prefix(0,'A',3);
#endif #endif
} }
@ -429,7 +425,7 @@ static void pwm_details(uint8_t pin) {
bool get_pinMode(int8_t pin) { return *portModeRegister(digitalPinToPort(pin)) & digitalPinToBitMask(pin); } bool get_pinMode(int8_t pin) { return *portModeRegister(digitalPinToPort(pin)) & digitalPinToBitMask(pin); }
#if !defined(digitalRead_mod) // use Teensyduino's version of digitalRead - it doesn't disable the PWMs #ifndef digitalRead_mod // use Teensyduino's version of digitalRead - it doesn't disable the PWMs
int digitalRead_mod(int8_t pin) { // same as digitalRead except the PWM stop section has been removed int digitalRead_mod(int8_t pin) { // same as digitalRead except the PWM stop section has been removed
uint8_t port = digitalPinToPort(pin); uint8_t port = digitalPinToPort(pin);
return (port != NOT_A_PIN) && (*portInputRegister(port) & digitalPinToBitMask(pin)) ? HIGH : LOW; return (port != NOT_A_PIN) && (*portInputRegister(port) & digitalPinToBitMask(pin)) ? HIGH : LOW;
@ -437,34 +433,31 @@ bool get_pinMode(int8_t pin) { return *portModeRegister(digitalPinToPort(pin)) &
#endif #endif
void print_port(int8_t pin) { // print port number void print_port(int8_t pin) { // print port number
#if defined(digitalPinToPort) #ifdef digitalPinToPort
SERIAL_PROTOCOLPGM(" Port: "); SERIAL_PROTOCOLPGM(" Port: ");
uint8_t x = digitalPinToPort(pin) + 64; uint8_t x = digitalPinToPort(pin) + 64;
SERIAL_CHAR(x); SERIAL_CHAR(x);
uint8_t temp = digitalPinToBitMask(pin); uint8_t temp = digitalPinToBitMask(pin);
for (x = '0'; (x < '9' && !(temp == 1)); x++){ for (x = '0'; x < '9' && temp != 1; x++) temp >>= 1;
temp = temp >> 1;
}
SERIAL_CHAR(x); SERIAL_CHAR(x);
#else #else
SERIAL_PROTOCOLPGM(" ") SERIAL_PROTOCOLPGM(" ");
#endif #endif
} }
// pretty report with PWM info // pretty report with PWM info
inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = true) { inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = true) {
uint8_t temp_char; uint8_t temp_char;
char *name_mem_pointer; char *name_mem_pointer;
char buffer[30]; // for the sprintf statements char buffer[30]; // for the sprintf statements
bool found = false; bool found = false,
bool multi_name_pin = false; multi_name_pin = false;
for (uint8_t x = 0; x < n_array; x++) { // scan entire array and report all instances of this pin for (uint8_t x = 0; x < n_array; x++) { // scan entire array and report all instances of this pin
if (pgm_read_byte(&pin_array[x][1]) == pin) { if (pgm_read_byte(&pin_array[x][1]) == pin) {
if (found == true) multi_name_pin = true; if (found) multi_name_pin = true;
found = true; found = true;
if (multi_name_pin == false) { // report digitial and analog pin number only on the first time through if (!multi_name_pin) { // report digitial and analog pin number only on the first time through
sprintf(buffer, "PIN:% 3d ", pin); // digital pin number sprintf(buffer, "PIN: %3d ", pin); // digital pin number
SERIAL_ECHO(buffer); SERIAL_ECHO(buffer);
print_port(pin); print_port(pin);
if (IS_ANALOG(pin)) { if (IS_ANALOG(pin)) {
@ -479,7 +472,7 @@ inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = t
temp_char = pgm_read_byte(name_mem_pointer + y); temp_char = pgm_read_byte(name_mem_pointer + y);
if (temp_char != 0) MYSERIAL.write(temp_char); if (temp_char != 0) MYSERIAL.write(temp_char);
else { else {
for (uint8_t i = 0; i < 28 - y; i++) MYSERIAL.write(" "); for (uint8_t i = 0; i < 28 - y; i++) MYSERIAL.write(' ');
break; break;
} }
} }
@ -487,12 +480,12 @@ inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = t
SERIAL_ECHOPGM("protected "); SERIAL_ECHOPGM("protected ");
else { else {
if (!(pgm_read_byte(&pin_array[x][2]))) { if (!(pgm_read_byte(&pin_array[x][2]))) {
sprintf(buffer, "Analog in =% 5d", analogRead(pin - analogInputToDigitalPin(0))); sprintf(buffer, "Analog in = %5d", analogRead(pin - analogInputToDigitalPin(0)));
SERIAL_ECHO(buffer); SERIAL_ECHO(buffer);
} }
else { else {
if (!get_pinMode(pin)) { if (!get_pinMode(pin)) {
// pinMode(pin, INPUT_PULLUP); // make sure input isn't floating - stopped doing this //pinMode(pin, INPUT_PULLUP); // make sure input isn't floating - stopped doing this
// because this could interfere with inductive/capacitive // because this could interfere with inductive/capacitive
// sensors (high impedance voltage divider) and with PT100 amplifier // sensors (high impedance voltage divider) and with PT100 amplifier
SERIAL_PROTOCOLPAIR("Input = ", digitalRead_mod(pin)); SERIAL_PROTOCOLPAIR("Input = ", digitalRead_mod(pin));
@ -502,43 +495,41 @@ inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = t
} }
else SERIAL_PROTOCOLPAIR("Output = ", digitalRead_mod(pin)); else SERIAL_PROTOCOLPAIR("Output = ", digitalRead_mod(pin));
} }
if (multi_name_pin == false && extended) pwm_details(pin); // report PWM capabilities only on the first pass & only if doing an extended report if (!multi_name_pin && extended) pwm_details(pin); // report PWM capabilities only on the first pass & only if doing an extended report
} }
SERIAL_EOL; SERIAL_EOL;
} // end of IF } // end of IF
} // end of for loop } // end of for loop
if (found == false) { if (!found) {
sprintf(buffer, "PIN:% 3d ", pin); sprintf(buffer, "PIN: %3d ", pin);
SERIAL_ECHO(buffer); SERIAL_ECHO(buffer);
print_port(pin); print_port(pin);
if (IS_ANALOG(pin)) { if (IS_ANALOG(pin)) {
sprintf(buffer, " (A%2d) ", int(pin - analogInputToDigitalPin(0))); // analog pin number sprintf(buffer, " (A%2d) ", int(pin - analogInputToDigitalPin(0))); // analog pin number
SERIAL_ECHO(buffer); SERIAL_ECHO(buffer);
} }
else SERIAL_ECHOPGM(" "); // add padding if not an analog pin else
SERIAL_ECHOPGM(" "); // add padding if not an analog pin
SERIAL_ECHOPGM("<unused/unknown>"); SERIAL_ECHOPGM("<unused/unknown>");
if (get_pinMode(pin)) { if (get_pinMode(pin))
SERIAL_PROTOCOLPAIR(" Output = ", digitalRead_mod(pin)); SERIAL_PROTOCOLPAIR(" Output = ", digitalRead_mod(pin));
}
else { else {
if (IS_ANALOG(pin)) { if (IS_ANALOG(pin)) {
sprintf(buffer, " Analog in =% 5d", analogRead(pin - analogInputToDigitalPin(0))); sprintf(buffer, " Analog in = %5d", analogRead(pin - analogInputToDigitalPin(0)));
SERIAL_ECHO(buffer); SERIAL_ECHO(buffer);
} }
else { else
SERIAL_ECHOPGM(" "); // add padding if not an analog pin SERIAL_ECHOPGM(" "); // add padding if not an analog pin
}
SERIAL_PROTOCOLPAIR(" Input = ", digitalRead_mod(pin)); SERIAL_PROTOCOLPAIR(" Input = ", digitalRead_mod(pin));
} }
// if (!pwm_status(pin)) SERIAL_ECHOPGM(" "); // add padding if it's not a PWM pin //if (!pwm_status(pin)) SERIAL_ECHOCHAR(' '); // add padding if it's not a PWM pin
if (extended) pwm_details(pin); // report PWM capabilities only if doing an extended report if (extended) pwm_details(pin); // report PWM capabilities only if doing an extended report
SERIAL_EOL; SERIAL_EOL;
} }
} }
inline void report_pin_state(int8_t pin) { inline void report_pin_state(int8_t pin) {
report_pin_state_extended(pin, false, false); report_pin_state_extended(pin, false, false);
} }

2
Marlin/printcounter.cpp
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

2
Marlin/printcounter.h
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

5
Marlin/stepper.cpp
Unescape View File

@ -346,8 +346,6 @@ ISR(TIMER1_COMPA_vect) {
void Stepper::isr() { void Stepper::isr() {
static uint32_t step_remaining = 0;
uint16_t ocr_val; uint16_t ocr_val;
#define ENDSTOP_NOMINAL_OCR_VAL 3000 // check endstops every 1.5ms to guarantee two stepper ISRs within 5ms for BLTouch #define ENDSTOP_NOMINAL_OCR_VAL 3000 // check endstops every 1.5ms to guarantee two stepper ISRs within 5ms for BLTouch
@ -364,6 +362,7 @@ void Stepper::isr() {
#if ENABLED(ENDSTOP_INTERRUPTS_FEATURE) #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
#define SPLIT(L) _SPLIT(L) #define SPLIT(L) _SPLIT(L)
#else // sample endstops in between step pulses #else // sample endstops in between step pulses
static uint32_t step_remaining = 0;
#define SPLIT(L) do { \ #define SPLIT(L) do { \
_SPLIT(L); \ _SPLIT(L); \
if (ENDSTOPS_ENABLED && L > ENDSTOP_NOMINAL_OCR_VAL) { \ if (ENDSTOPS_ENABLED && L > ENDSTOP_NOMINAL_OCR_VAL) { \
@ -391,7 +390,7 @@ void Stepper::isr() {
_ENABLE_ISRs(); // re-enable ISRs _ENABLE_ISRs(); // re-enable ISRs
return; return;
} }
# endif #endif
if (cleaning_buffer_counter) { if (cleaning_buffer_counter) {
--cleaning_buffer_counter; --cleaning_buffer_counter;

2
Marlin/stopwatch.cpp
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

2
Marlin/stopwatch.h
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

2
Marlin/twibus.cpp
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

2
Marlin/twibus.h
Unescape View File

@ -1,4 +1,4 @@
/* /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *

Write Preview
Loading…
Cancel
Save