#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
@ -786,11 +884,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Preheat Constants
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 100// Insert Value between 0 and 255
#define PLA_PREHEAT_FAN_SPEED 255// Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 100// Insert Value between 0 and 255
#define ABS_PREHEAT_FAN_SPEED 255// Insert Value between 0 and 255
//============================= LCD and SD support ============================
//============================= LCD and SD support ============================
@ -1151,8 +1249,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
#define MEASURED_LOWER_LIMIT 1.60 //lower limit factor for sensor reading validation in mm
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
@ -285,7 +285,7 @@
// Default stepper release if idle. Set to 0 to deactivate.
// Default stepper release if idle. Set to 0 to deactivate.
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
// Time can be set by M18 and M84.
// Time can be set by M18 and M84.
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
#define DEFAULT_STEPPER_DEACTIVE_TIME 120
#define DISABLE_INACTIVE_X true
#define DISABLE_INACTIVE_X true
#define DISABLE_INACTIVE_Y true
#define DISABLE_INACTIVE_Y true
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
@ -297,7 +297,8 @@
// @section lcd
// @section lcd
#if ENABLED(ULTIPANEL)
#if ENABLED(ULTIPANEL)
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
#define MANUAL_FEEDRATE_XYZ 50*60
#define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
#endif
#endif
@ -307,7 +308,8 @@
#define DEFAULT_MINSEGMENTTIME 20000
#define DEFAULT_MINSEGMENTTIME 20000
// If defined the movements slow down when the look ahead buffer is only half full
// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN
// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second)
This example configuration ist for a Kossel XL with a printable bed diameter of 280mm and a height of 385mm. It also has the auto bed leveling probe (with a endstop switch) and the heat bed activated.
This example configuration is for a Kossel XL with a printable bed diameter of 280mm and a height of 380mm. It also has the auto bed leveling probe (with an endstop switch) and the heated bed activated.
## Configuration
## Configuration
You might have/want to edit at least the following settings in Configuration.h:
You might need (or want) to edit at least the following settings in `Configuration.h`:
* <code>MANUAL_Z_HOME_POS<code> The hight of your printing space available, auto bed leveling makes this not as important as before
* `MANUAL_Z_HOME_POS` - The available height of your printing space. Auto Bed Leveling makes it less important to have the exact value.
* <code>DELTA_PRINTABLE_RADIUS</code> The printable radius
* `DELTA_PRINTABLE_RADIUS` - The printable radius is how far from the center the nozzle can reach.
* <code>DEFAULT_AXIS_STEPS_PER_UNIT</code> [http://zennmaster.com/makingstuff/reprap-101-calibrating-your-extruder-part-1-e-steps](The steps for the extruder to optimize the amount of filament flow)
* `DEFAULT_AXIS_STEPS_PER_UNIT` - Steps-per-millimeter for the delta steppers, and for the extruder [to optimize the amount of filament flow](http://zennmaster.com/makingstuff/reprap-101-calibrating-your-extruder-part-1-e-steps).
### Fine tuning
### Fine tuning
* Increase <code>DELTA_RADIUS</code> when the model is convex (bulge in the middle)
* Increase `DELTA_RADIUS` if the model comes out convex (with a bulge in the middle)
* Increase <code>DELTA_DIAGONAL_ROD</code> when the model is larger then expected
* Increase `DELTA_DIAGONAL_ROD` if the model comes out larger than expected
Marc Urben
9 years ago
committed by