forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Merge remote-tracking branch 'origin/Marlin_v1' into Marlin_v1

Browse Source
master
Erik van der Zalm 13 years ago
parent 65934eee9c 9980ceb4a3
commit ac82411c73
16 changed files with 1434 additions and 1147 deletions
Show Stats Download Patch File Download Diff File

268
Marlin/Configuration.h
Unescape View File

@ -1,10 +1,13 @@
#ifndef __CONFIGURATION_H #ifndef __CONFIGURATION_H
#define __CONFIGURATION_H #define __CONFIGURATION_H
//#define DEBUG_STEPS
#define MM_PER_ARC_SEGMENT 1
#define N_ARC_CORRECTION 25 // This determines the communication speed of the printer
//#define BAUDRATE 250000
#define BAUDRATE 115200
//#define BAUDRATE 230400
// Frequency limit // Frequency limit
// See nophead's blog for more info // See nophead's blog for more info
@ -26,7 +29,9 @@
// Teensylu = 8 // Teensylu = 8
#define MOTHERBOARD 7 #define MOTHERBOARD 7
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
//// Thermistor settings: //// Thermistor settings:
// 1 is 100k thermistor // 1 is 100k thermistor
@ -49,49 +54,103 @@
//#define BED_USES_THERMISTOR //#define BED_USES_THERMISTOR
//#define BED_USES_AD595 //#define BED_USES_AD595
#define HEATER_CHECK_INTERVAL 50 #define HEATER_CHECK_INTERVAL 50 //ms
#define BED_CHECK_INTERVAL 5000 #define BED_CHECK_INTERVAL 5000 //ms
//// Experimental watchdog and minimal temp
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
/// CURRENTLY NOT IMPLEMENTED AND UNUSEABLE
//#define WATCHPERIOD 5000 //5 seconds
//// Endstop Settings // Actual temperature must be close to target for this long before M109 returns success
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors //#define TEMP_RESIDENCY_TIME 20 // (seconds)
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. //#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one
const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
// This determines the communication speed of the printer //// The minimal temperature defines the temperature below which the heater will not be enabled
#define BAUDRATE 250000 #define HEATER_0_MINTEMP 5
//#define BAUDRATE 115200 //#define HEATER_1_MINTEMP 5
//#define BAUDRATE 230400 //#define BED_MINTEMP 5
// Comment out (using // at the start of the line) to disable SD support:
// #define ULTRA_LCD //any lcd // When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275
//#define_HEATER_1_MAXTEMP 275
//#define BED_MAXTEMP 150
#define ULTIPANEL
#ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel // PID settings:
#define SDSUPPORT // Uncomment the following line to enable PID support.
#define ULTRA_LCD
#define LCD_WIDTH 20 #define PIDTEMP
#define LCD_HEIGHT 4 #ifdef PIDTEMP
#else //no panel but just lcd //#define PID_DEBUG // Sends debug data to the serial port.
#ifdef ULTRA_LCD //#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define LCD_WIDTH 16
#define LCD_HEIGHT 2 #define PID_MAX 255 // limits current to nozzle; 255=full current
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID
#define PID_dT 0.1 //sampling period of the PID
//To develop some PID settings for your machine, you can initiall follow
// the Ziegler-Nichols method.
// set Ki and Kd to zero.
// heat with a defined Kp and see if the temperature stabilizes
// ideally you do this graphically with repg.
// the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde
// PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain
// usually further manual tunine is necessary.
#define PID_CRITIAL_GAIN 3000
#define PID_SWING_AT_CRITIAL 45 //seconds
#define PID_PI //no differentail term
//#define PID_PID //normal PID
#ifdef PID_PID
//PID according to Ziegler-Nichols method
#define DEFAULT_Kp (0.6*PID_CRITIAL_GAIN)
#define DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT)
#endif #endif
#endif
#ifdef PID_PI
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#endif
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (3) //heatingpower=Kc*(e_speed)
#endif
#endif // PIDTEMP
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
const int dropsegments=5; //everything with this number of steps will be ignored as move
//// ADVANCED SETTINGS - to tweak parameters
#include "thermistortables.h"
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0 #define X_ENABLE_ON 0
@ -156,88 +215,33 @@ const int dropsegments=5; //everything with this number of steps will be ignore
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec)
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
//this enables the watchdog interrupt.
#define USE_WATCHDOG
//you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
#define RESET_MANUAL
#define WATCHDOG_TIMEOUT 4
//// Experimental watchdog and minimal temp
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
/// CURRENTLY NOT IMPLEMENTED AND UNUSEABLE
//#define WATCHPERIOD 5000 //5 seconds
// Actual temperature must be close to target for this long before M109 returns success
//#define TEMP_RESIDENCY_TIME 20 // (seconds)
//#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled //===========================================================================
//#define HEATER_0_MINTEMP 5 //=============================Additional Features===========================
//#define HEATER_1_MINTEMP 5 //===========================================================================
//#define BED_MINTEMP 5
// EEPROM
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support
#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can.
#define EEPROM_CHITCHAT
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
//#define HEATER_0_MAXTEMP 275
//#define_HEATER_1_MAXTEMP 275
//#define BED_MAXTEMP 150
/// PID settings: // The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// Uncomment the following line to enable PID support. // this enables the watchdog interrupt.
#define USE_WATCHDOG
#define PIDTEMP // you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
#ifdef PIDTEMP #define RESET_MANUAL
//#define PID_DEBUG // Sends debug data to the serial port. #define WATCHDOG_TIMEOUT 4 //seconds
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define PID_MAX 255 // limits current to nozzle; 255=full current
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID
#define PID_dT 0.1 //sampling period of the PID
//To develop some PID settings for your machine, you can initiall follow
// the Ziegler-Nichols method.
// set Ki and Kd to zero.
// heat with a defined Kp and see if the temperature stabilizes
// ideally you do this graphically with repg.
// the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde
// PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain
// usually further manual tunine is necessary.
#define PID_CRITIAL_GAIN 3000
#define PID_SWING_AT_CRITIAL 45 //seconds
#define PID_PI //no differentail term
//#define PID_PID //normal PID
#ifdef PID_PID
//PID according to Ziegler-Nichols method
#define DEFAULT_Kp (0.6*PID_CRITIAL_GAIN)
#define DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT)
#endif
#ifdef PID_PI
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#endif
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (5) //heatingpower=Kc*(e_speed)
#endif
#endif // PIDTEMP
// extruder advance constant (s2/mm3) // extruder advance constant (s2/mm3)
// //
@ -258,6 +262,52 @@ const int dropsegments=5; //everything with this number of steps will be ignore
#endif // ADVANCE #endif // ADVANCE
//LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
#define ULTIPANEL
#ifdef ULTIPANEL
#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
#define LCD_HEIGHT 4
#else //no panel but just lcd
#ifdef ULTRA_LCD
#define LCD_WIDTH 16
#define LCD_HEIGHT 2
#endif
#endif
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
//#define DEBUG_STEPS
// Arc interpretation settings:
#define MM_PER_ARC_SEGMENT 1
#define N_ARC_CORRECTION 25
//automatic temperature: just for testing, this is very dangerous, keep disabled!
// not working yet.
//Erik: the settings currently depend dramatically on skeinforge39 or 41.
//#define AUTOTEMP
#define AUTOTEMP_MIN 190
#define AUTOTEMP_MAX 260
#define AUTOTEMP_FACTOR 1000. //current target temperature= min+largest buffered espeeds)*FACTOR
const int dropsegments=0; //everything with less than this number of steps will be ignored as move and joined with the next movement
//===========================================================================
//=============================Buffers ============================
//===========================================================================
// The number of linear motions that can be in the plan at any give time. // The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
#if defined SDSUPPORT #if defined SDSUPPORT
@ -266,8 +316,12 @@ const int dropsegments=5; //everything with this number of steps will be ignore
#define BLOCK_BUFFER_SIZE 8 // maximize block buffer #define BLOCK_BUFFER_SIZE 8 // maximize block buffer
#endif #endif
//The ASCII buffer for recieving from the serial: //The ASCII buffer for recieving from the serial:
#define MAX_CMD_SIZE 96 #define MAX_CMD_SIZE 96
#define BUFSIZE 4 #define BUFSIZE 4
#include "thermistortables.h"
#endif //__CONFIGURATION_H #endif //__CONFIGURATION_H

166
Marlin/EEPROMwrite.h
Unescape View File

@ -25,6 +25,9 @@ template <class T> int EEPROM_readAnything(int &ee, T& value)
} }
//====================================================================================== //======================================================================================
#define EEPROM_OFFSET 100 #define EEPROM_OFFSET 100
@ -35,8 +38,9 @@ template <class T> int EEPROM_readAnything(int &ee, T& value)
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order. // ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
#define EEPROM_VERSION "V04" #define EEPROM_VERSION "V04"
void StoreSettings() inline void StoreSettings()
{ {
#ifdef EEPROM_SETTINGS
char ver[4]= "000"; char ver[4]= "000";
int i=EEPROM_OFFSET; int i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver); // invalidate data first EEPROM_writeAnything(i,ver); // invalidate data first
@ -62,71 +66,115 @@ void StoreSettings()
char ver2[4]=EEPROM_VERSION; char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET; i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver2); // validate data EEPROM_writeAnything(i,ver2); // validate data
SERIAL_ECHOLN("Settings Stored"); SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
#endif //EEPROM_SETTINGS
} }
void RetrieveSettings(bool def=false) inline void RetrieveSettings(bool def=false)
{ // if def=true, the default values will be used { // if def=true, the default values will be used
int i=EEPROM_OFFSET; #ifdef EEPROM_SETTINGS
char stored_ver[4]; int i=EEPROM_OFFSET;
char ver[4]=EEPROM_VERSION; char stored_ver[4];
EEPROM_readAnything(i,stored_ver); //read stored version char ver[4]=EEPROM_VERSION;
// SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]"); EEPROM_readAnything(i,stored_ver); //read stored version
if ((!def)&&(strncmp(ver,stored_ver,3)==0)) // SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
{ // version number match if ((!def)&&(strncmp(ver,stored_ver,3)==0))
EEPROM_readAnything(i,axis_steps_per_unit); { // version number match
EEPROM_readAnything(i,max_feedrate); EEPROM_readAnything(i,axis_steps_per_unit);
EEPROM_readAnything(i,max_acceleration_units_per_sq_second); EEPROM_readAnything(i,max_feedrate);
EEPROM_readAnything(i,acceleration); EEPROM_readAnything(i,max_acceleration_units_per_sq_second);
EEPROM_readAnything(i,retract_acceleration); EEPROM_readAnything(i,acceleration);
EEPROM_readAnything(i,minimumfeedrate); EEPROM_readAnything(i,retract_acceleration);
EEPROM_readAnything(i,mintravelfeedrate); EEPROM_readAnything(i,minimumfeedrate);
EEPROM_readAnything(i,minsegmenttime); EEPROM_readAnything(i,mintravelfeedrate);
EEPROM_readAnything(i,max_xy_jerk); EEPROM_readAnything(i,minsegmenttime);
EEPROM_readAnything(i,max_z_jerk); EEPROM_readAnything(i,max_xy_jerk);
#ifndef PIDTEMP EEPROM_readAnything(i,max_z_jerk);
float Kp,Ki,Kd; #ifndef PIDTEMP
#endif float Kp,Ki,Kd;
EEPROM_readAnything(i,Kp); #endif
EEPROM_readAnything(i,Ki); EEPROM_readAnything(i,Kp);
EEPROM_readAnything(i,Kd); EEPROM_readAnything(i,Ki);
EEPROM_readAnything(i,Kd);
SERIAL_ECHOLN("Stored settings retreived:"); SERIAL_ECHO_START;
} SERIAL_ECHOLNPGM("Stored settings retreived:");
else }
{ else
float tmp1[]=DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[]=DEFAULT_MAX_FEEDRATE;
long tmp3[]=DEFAULT_MAX_ACCELERATION;
for (short i=0;i<4;i++)
{ {
axis_steps_per_unit[i]=tmp1[i]; float tmp1[]=DEFAULT_AXIS_STEPS_PER_UNIT;
max_feedrate[i]=tmp2[i]; float tmp2[]=DEFAULT_MAX_FEEDRATE;
max_acceleration_units_per_sq_second[i]=tmp3[i]; long tmp3[]=DEFAULT_MAX_ACCELERATION;
for (short i=0;i<4;i++)
{
axis_steps_per_unit[i]=tmp1[i];
max_feedrate[i]=tmp2[i];
max_acceleration_units_per_sq_second[i]=tmp3[i];
}
acceleration=DEFAULT_ACCELERATION;
retract_acceleration=DEFAULT_RETRACT_ACCELERATION;
minimumfeedrate=DEFAULT_MINIMUMFEEDRATE;
minsegmenttime=DEFAULT_MINSEGMENTTIME;
mintravelfeedrate=DEFAULT_MINTRAVELFEEDRATE;
max_xy_jerk=DEFAULT_XYJERK;
max_z_jerk=DEFAULT_ZJERK;
SERIAL_ECHO_START;
SERIAL_ECHOLN("Using Default settings:");
} }
acceleration=DEFAULT_ACCELERATION; #ifdef EEPROM_CHITCHAT
retract_acceleration=DEFAULT_RETRACT_ACCELERATION; SERIAL_ECHO_START;
minimumfeedrate=DEFAULT_MINIMUMFEEDRATE; SERIAL_ECHOLNPGM("Steps per unit:");
minsegmenttime=DEFAULT_MINSEGMENTTIME; SERIAL_ECHO_START;
mintravelfeedrate=DEFAULT_MINTRAVELFEEDRATE; SERIAL_ECHOPAIR(" M92 X",axis_steps_per_unit[0]);
max_xy_jerk=DEFAULT_XYJERK; SERIAL_ECHOPAIR(" Y",axis_steps_per_unit[1]);
max_z_jerk=DEFAULT_ZJERK; SERIAL_ECHOPAIR(" Z",axis_steps_per_unit[2]);
SERIAL_ECHOLN("Using Default settings:"); SERIAL_ECHOPAIR(" E",axis_steps_per_unit[3]);
} SERIAL_ECHOLN("");
SERIAL_ECHOLN("Steps per unit:");
SERIAL_ECHOLN(" M92 X" <<_FLOAT(axis_steps_per_unit[0],3) << " Y" << _FLOAT(axis_steps_per_unit[1],3) << " Z" << _FLOAT(axis_steps_per_unit[2],3) << " E" << _FLOAT(axis_steps_per_unit[3],3)); SERIAL_ECHO_START;
SERIAL_ECHOLN("Maximum feedrates (mm/s):"); SERIAL_ECHOLNPGM("Maximum feedrates (mm/s):");
SERIAL_ECHOLN(" M203 X" <<_FLOAT(max_feedrate[0]/60,2)<<" Y" << _FLOAT(max_feedrate[1]/60,2) << " Z" << _FLOAT(max_feedrate[2]/60,2) << " E" << _FLOAT(max_feedrate[3]/60,2)); SERIAL_ECHO_START;
SERIAL_ECHOLN("Maximum Acceleration (mm/s2):"); SERIAL_ECHOPAIR(" M203 X",max_feedrate[0]/60);
SERIAL_ECHOLN(" M201 X" <<_FLOAT(max_acceleration_units_per_sq_second[0],0) << " Y" << _FLOAT(max_acceleration_units_per_sq_second[1],0) << " Z" << _FLOAT(max_acceleration_units_per_sq_second[2],0) << " E" << _FLOAT(max_acceleration_units_per_sq_second[3],0)); SERIAL_ECHOPAIR(" Y",max_feedrate[1]/60 );
SERIAL_ECHOLN("Acceleration: S=acceleration, T=retract acceleration"); SERIAL_ECHOPAIR(" Z", max_feedrate[2]/60 );
SERIAL_ECHOLN(" M204 S" <<_FLOAT(acceleration,2) << " T" << _FLOAT(retract_acceleration,2)); SERIAL_ECHOPAIR(" E", max_feedrate[3]/60);
SERIAL_ECHOLN("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)"); SERIAL_ECHOLN("");
SERIAL_ECHOLN(" M205 S" <<_FLOAT(minimumfeedrate/60,2) << " T" << _FLOAT(mintravelfeedrate/60,2) << " B" << _FLOAT(minsegmenttime,2) << " X" << _FLOAT(max_xy_jerk/60,2) << " Z" << _FLOAT(max_z_jerk/60,2)); SERIAL_ECHO_START;
#ifdef PIDTEMP SERIAL_ECHOLNPGM("Maximum Acceleration (mm/s2):");
SERIAL_ECHOLN("PID settings:"); SERIAL_ECHO_START;
SERIAL_ECHOLN(" M301 P" << _FLOAT(Kp,3) << " I" << _FLOAT(Ki,3) << " D" << _FLOAT(Kd,3)); SERIAL_ECHOPAIR(" M201 X" ,max_acceleration_units_per_sq_second[0] );
SERIAL_ECHOPAIR(" Y" , max_acceleration_units_per_sq_second[1] );
SERIAL_ECHOPAIR(" Z" ,max_acceleration_units_per_sq_second[2] );
SERIAL_ECHOPAIR(" E" ,max_acceleration_units_per_sq_second[3]);
SERIAL_ECHOLN("");
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Acceleration: S=acceleration, T=retract acceleration");
SERIAL_ECHO_START;
SERIAL_ECHOPAIR(" M204 S",acceleration );
SERIAL_ECHOPAIR(" T" ,retract_acceleration);
SERIAL_ECHOLN("");
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)");
SERIAL_ECHO_START;
SERIAL_ECHOPAIR(" M205 S",minimumfeedrate/60 );
SERIAL_ECHOPAIR(" T" ,mintravelfeedrate/60 );
SERIAL_ECHOPAIR(" B" ,minsegmenttime );
SERIAL_ECHOPAIR(" X" ,max_xy_jerk/60 );
SERIAL_ECHOPAIR(" Z" ,max_z_jerk/60);
SERIAL_ECHOLN("");
#ifdef PIDTEMP
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("PID settings:");
SERIAL_ECHO_START;
SERIAL_ECHOPAIR(" M301 P",Kp );
SERIAL_ECHOPAIR(" I" ,Ki );
SERIAL_ECHOPAIR(" D" ,Kd);
SERIAL_ECHOLN("");
#endif
#endif #endif
#endif //EEPROM_SETTINGS
} }
#endif #endif

51
Marlin/Marlin.h
Unescape View File

@ -5,12 +5,52 @@
// Licence: GPL // Licence: GPL
#include <WProgram.h> #include <WProgram.h>
#include "fastio.h" #include "fastio.h"
#include <avr/pgmspace.h>
#include "Configuration.h"
//#define SERIAL_ECHO(x) Serial << "echo: " << x;
//#define SERIAL_ECHOLN(x) Serial << "echo: "<<x<<endl;
//#define SERIAL_ERROR(x) Serial << "Error: " << x;
//#define SERIAL_ERRORLN(x) Serial << "Error: " << x<<endl;
//#define SERIAL_PROTOCOL(x) Serial << x;
//#define SERIAL_PROTOCOLLN(x) Serial << x<<endl;
#define SERIAL_PROTOCOL(x) Serial.print(x);
#define SERIAL_PROTOCOLPGM(x) serialprintPGM(PSTR(x));
#define SERIAL_PROTOCOLLN(x) {Serial.print(x);Serial.write('\n');}
#define SERIAL_PROTOCOLLNPGM(x) {serialprintPGM(PSTR(x));Serial.write('\n');}
const char errormagic[] PROGMEM ="Error:";
const char echomagic[] PROGMEM ="echo:";
#define SERIAL_ERROR_START serialprintPGM(errormagic);
#define SERIAL_ERROR(x) SERIAL_PROTOCOL(x)
#define SERIAL_ERRORPGM(x) SERIAL_PROTOCOLPGM(x)
#define SERIAL_ERRORLN(x) SERIAL_PROTOCOLLN(x)
#define SERIAL_ERRORLNPGM(x) SERIAL_PROTOCOLLNPGM(x)
#define SERIAL_ECHO_START serialprintPGM(echomagic);
#define SERIAL_ECHO(x) SERIAL_PROTOCOL(x)
#define SERIAL_ECHOPGM(x) SERIAL_PROTOCOLPGM(x)
#define SERIAL_ECHOLN(x) SERIAL_PROTOCOLLN(x)
#define SERIAL_ECHOLNPGM(x) SERIAL_PROTOCOLLNPGM(x)
#define SERIAL_ECHOPAIR(name,value) {SERIAL_ECHOPGM(name);SERIAL_ECHO(value);}
//things to write to serial from Programmemory. saves 400 to 2k of RAM.
#define SerialprintPGM(x) serialprintPGM(PSTR(x))
inline void serialprintPGM(const char *str)
{
char ch=pgm_read_byte(str);
while(ch)
{
Serial.write(ch);
ch=pgm_read_byte(++str);
}
}
#include "streaming.h"
#define SERIAL_ECHO(x) Serial << "echo: " << x;
#define SERIAL_ECHOLN(x) Serial << "echo: "<<x<<endl;
#define SERIAL_ERROR(x) Serial << "echo: ERROR: " << x;
#define SERIAL_ERRORLN(x) Serial << "echo: ERROR: " << x<<endl;
void get_command(); void get_command();
void process_commands(); void process_commands();
@ -69,5 +109,6 @@ void enquecommand(const char *cmd); //put an ascii command at the end of the cur
extern float homing_feedrate[]; extern float homing_feedrate[];
extern bool axis_relative_modes[]; extern bool axis_relative_modes[];
extern float current_position[NUM_AXIS] ;
#endif #endif

255
Marlin/Marlin.pde
Unescape View File

@ -32,7 +32,6 @@
#include "pins.h" #include "pins.h"
#include "Marlin.h" #include "Marlin.h"
#include "ultralcd.h" #include "ultralcd.h"
#include "streaming.h"
#include "planner.h" #include "planner.h"
#include "stepper.h" #include "stepper.h"
#include "temperature.h" #include "temperature.h"
@ -40,7 +39,8 @@
#include "cardreader.h" #include "cardreader.h"
char version_string[] = "1.0.0 Alpha 1"; #define VERSION_STRING "1.0.0 Alpha 1"
@ -99,8 +99,9 @@ char version_string[] = "1.0.0 Alpha 1";
// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk // M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk
// M220 - set speed factor override percentage S:factor in percent // M220 - set speed factor override percentage S:factor in percent
// M301 - Set PID parameters P I and D // M301 - Set PID parameters P I and D
// M400 - Finish all moves
// M500 - stores paramters in EEPROM // M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). D // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//Stepper Movement Variables //Stepper Movement Variables
@ -122,13 +123,14 @@ bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
volatile int feedmultiply=100; //100->1 200->2 volatile int feedmultiply=100; //100->1 200->2
int saved_feedmultiply; int saved_feedmultiply;
volatile bool feedmultiplychanged=false; volatile bool feedmultiplychanged=false;
float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0};
//=========================================================================== //===========================================================================
//=============================private variables============================= //=============================private variables=============================
//=========================================================================== //===========================================================================
const char axis_codes[NUM_AXIS] = {'X', 'Y', 'Z', 'E'}; const char axis_codes[NUM_AXIS] = {'X', 'Y', 'Z', 'E'};
static float destination[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0}; static float destination[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0};
static float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0};
static float offset[3] = {0.0, 0.0, 0.0}; static float offset[3] = {0.0, 0.0, 0.0};
static bool home_all_axis = true; static bool home_all_axis = true;
static float feedrate = 1500.0, next_feedrate, saved_feedrate; static float feedrate = 1500.0, next_feedrate, saved_feedrate;
@ -173,6 +175,23 @@ static unsigned long stoptime=0;
//=========================================================================== //===========================================================================
extern "C"{
extern unsigned int __bss_end;
extern unsigned int __heap_start;
extern void *__brkval;
int freeMemory() {
int free_memory;
if((int)__brkval == 0)
free_memory = ((int)&free_memory) - ((int)&__bss_end);
else
free_memory = ((int)&free_memory) - ((int)__brkval);
return free_memory;
}
}
//adds an command to the main command buffer //adds an command to the main command buffer
//thats really done in a non-safe way. //thats really done in a non-safe way.
@ -183,7 +202,10 @@ void enquecommand(const char *cmd)
{ {
//this is dangerous if a mixing of serial and this happsens //this is dangerous if a mixing of serial and this happsens
strcpy(&(cmdbuffer[bufindw][0]),cmd); strcpy(&(cmdbuffer[bufindw][0]),cmd);
SERIAL_ECHOLN("enqueing \""<<cmdbuffer[bufindw]<<"\""); SERIAL_ECHO_START;
SERIAL_ECHOPGM("enqueing \"");
SERIAL_ECHO(cmdbuffer[bufindw]);
SERIAL_ECHOLNPGM("\"");
bufindw= (bufindw + 1)%BUFSIZE; bufindw= (bufindw + 1)%BUFSIZE;
buflen += 1; buflen += 1;
} }
@ -192,8 +214,12 @@ void enquecommand(const char *cmd)
void setup() void setup()
{ {
Serial.begin(BAUDRATE); Serial.begin(BAUDRATE);
SERIAL_ECHOLN("Marlin "<<version_string); SERIAL_ECHO_START;
Serial.println("start"); SERIAL_ECHOLNPGM(VERSION_STRING);
SERIAL_PROTOCOLLNPGM("start");
SERIAL_ECHO_START;
SERIAL_ECHOPGM("Free Memory:");
SERIAL_ECHOLN(freeMemory());
for(int8_t i = 0; i < BUFSIZE; i++) for(int8_t i = 0; i < BUFSIZE; i++)
{ {
fromsd[i] = false; fromsd[i] = false;
@ -228,12 +254,12 @@ void loop()
if(strstr(cmdbuffer[bufindr],"M29") == NULL) if(strstr(cmdbuffer[bufindr],"M29") == NULL)
{ {
card.write_command(cmdbuffer[bufindr]); card.write_command(cmdbuffer[bufindr]);
Serial.println("ok"); SERIAL_PROTOCOLLNPGM("ok");
} }
else else
{ {
card.closefile(); card.closefile();
Serial.println("Done saving file."); SERIAL_PROTOCOLLNPGM("Done saving file.");
} }
} }
else else
@ -249,6 +275,7 @@ void loop()
//check heater every n milliseconds //check heater every n milliseconds
manage_heater(); manage_heater();
manage_inactivity(1); manage_inactivity(1);
checkHitEndstops();
LCD_STATUS; LCD_STATUS;
} }
@ -268,8 +295,9 @@ inline void get_command()
strchr_pointer = strchr(cmdbuffer[bufindw], 'N'); strchr_pointer = strchr(cmdbuffer[bufindw], 'N');
gcode_N = (strtol(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL, 10)); gcode_N = (strtol(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL, 10));
if(gcode_N != gcode_LastN+1 && (strstr(cmdbuffer[bufindw], "M110") == NULL) ) { if(gcode_N != gcode_LastN+1 && (strstr(cmdbuffer[bufindw], "M110") == NULL) ) {
Serial.print("Serial Error: Line Number is not Last Line Number+1, Last Line:"); SERIAL_ERROR_START;
Serial.println(gcode_LastN); SERIAL_ERRORPGM("Line Number is not Last Line Number+1, Last Line:");
SERIAL_ERRORLN(gcode_LastN);
//Serial.println(gcode_N); //Serial.println(gcode_N);
FlushSerialRequestResend(); FlushSerialRequestResend();
serial_count = 0; serial_count = 0;
@ -284,8 +312,9 @@ inline void get_command()
strchr_pointer = strchr(cmdbuffer[bufindw], '*'); strchr_pointer = strchr(cmdbuffer[bufindw], '*');
if( (int)(strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)) != checksum) { if( (int)(strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)) != checksum) {
Serial.print("Error: checksum mismatch, Last Line:"); SERIAL_ERROR_START;
Serial.println(gcode_LastN); SERIAL_ERRORPGM("checksum mismatch, Last Line:");
SERIAL_ERRORLN(gcode_LastN);
FlushSerialRequestResend(); FlushSerialRequestResend();
serial_count = 0; serial_count = 0;
return; return;
@ -294,8 +323,9 @@ inline void get_command()
} }
else else
{ {
Serial.print("Error: No Checksum with line number, Last Line:"); SERIAL_ERROR_START;
Serial.println(gcode_LastN); SERIAL_ERRORPGM("No Checksum with line number, Last Line:");
SERIAL_ERRORLN(gcode_LastN);
FlushSerialRequestResend(); FlushSerialRequestResend();
serial_count = 0; serial_count = 0;
return; return;
@ -308,8 +338,9 @@ inline void get_command()
{ {
if((strstr(cmdbuffer[bufindw], "*") != NULL)) if((strstr(cmdbuffer[bufindw], "*") != NULL))
{ {
Serial.print("Error: No Line Number with checksum, Last Line:"); SERIAL_ERROR_START;
Serial.println(gcode_LastN); SERIAL_ERRORPGM("No Line Number with checksum, Last Line:");
SERIAL_ERRORLN(gcode_LastN);
serial_count = 0; serial_count = 0;
return; return;
} }
@ -325,7 +356,7 @@ inline void get_command()
if(card.saving) if(card.saving)
break; break;
#endif //SDSUPPORT #endif //SDSUPPORT
Serial.println("ok"); SERIAL_PROTOCOLLNPGM("ok");
break; break;
default: default:
break; break;
@ -350,22 +381,23 @@ inline void get_command()
return; return;
} }
while( !card.eof() && buflen < BUFSIZE) { while( !card.eof() && buflen < BUFSIZE) {
int16_t n=card.get();
serial_char = card.get(); serial_char = (char)n;
if(serial_char == '\n' || serial_char == '\r' || serial_char == ':' || serial_count >= (MAX_CMD_SIZE - 1)) if(serial_char == '\n' || serial_char == '\r' || serial_char == ':' || serial_count >= (MAX_CMD_SIZE - 1)||n==-1)
{ {
if(card.eof()){ if(card.eof()){
card.sdprinting = false; card.sdprinting = false;
Serial.println("echo: Done printing file"); SERIAL_PROTOCOLLNPGM("Done printing file");
stoptime=millis(); stoptime=millis();
char time[30]; char time[30];
unsigned long t=(stoptime-starttime)/1000; unsigned long t=(stoptime-starttime)/1000;
int sec,min; int sec,min;
min=t/60; min=t/60;
sec=t%60; sec=t%60;
sprintf(time,"echo: %i min, %i sec",min,sec); sprintf(time,"%i min, %i sec",min,sec);
Serial.println(time); SERIAL_ECHO_START;
SERIAL_ECHOLN(time);
LCD_MESSAGE(time); LCD_MESSAGE(time);
card.checkautostart(true); card.checkautostart(true);
} }
@ -386,6 +418,7 @@ inline void get_command()
if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char;
} }
} }
#endif //SDSUPPORT #endif //SDSUPPORT
} }
@ -417,20 +450,25 @@ inline bool code_seen(char code)
destination[LETTER##_AXIS] = 1.5 * LETTER##_MAX_LENGTH * LETTER##_HOME_DIR; \ destination[LETTER##_AXIS] = 1.5 * LETTER##_MAX_LENGTH * LETTER##_HOME_DIR; \
feedrate = homing_feedrate[LETTER##_AXIS]; \ feedrate = homing_feedrate[LETTER##_AXIS]; \
prepare_move(); \ prepare_move(); \
st_synchronize();\
\ \
current_position[LETTER##_AXIS] = 0;\ current_position[LETTER##_AXIS] = 0;\
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\ plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\
destination[LETTER##_AXIS] = -5 * LETTER##_HOME_DIR;\ destination[LETTER##_AXIS] = -5 * LETTER##_HOME_DIR;\
prepare_move(); \ prepare_move(); \
st_synchronize();\
\ \
destination[LETTER##_AXIS] = 10 * LETTER##_HOME_DIR;\ destination[LETTER##_AXIS] = 10 * LETTER##_HOME_DIR;\
feedrate = homing_feedrate[LETTER##_AXIS]/2 ; \ feedrate = homing_feedrate[LETTER##_AXIS]/2 ; \
prepare_move(); \ prepare_move(); \
st_synchronize();\
\ \
current_position[LETTER##_AXIS] = (LETTER##_HOME_DIR == -1) ? 0 : LETTER##_MAX_LENGTH;\ current_position[LETTER##_AXIS] = (LETTER##_HOME_DIR == -1) ? 0 : LETTER##_MAX_LENGTH;\
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\ plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\
destination[LETTER##_AXIS] = current_position[LETTER##_AXIS];\ destination[LETTER##_AXIS] = current_position[LETTER##_AXIS];\
feedrate = 0.0;\ feedrate = 0.0;\
st_synchronize();\
endstops_hit_on_purpose();\
} }
inline void process_commands() inline void process_commands()
@ -461,6 +499,7 @@ inline void process_commands()
previous_millis_cmd = millis(); previous_millis_cmd = millis();
return; return;
case 4: // G4 dwell case 4: // G4 dwell
LCD_MESSAGEPGM("DWELL...");
codenum = 0; codenum = 0;
if(code_seen('P')) codenum = code_value(); // milliseconds to wait if(code_seen('P')) codenum = code_value(); // milliseconds to wait
if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
@ -495,6 +534,7 @@ inline void process_commands()
feedrate = saved_feedrate; feedrate = saved_feedrate;
feedmultiply = saved_feedmultiply; feedmultiply = saved_feedmultiply;
previous_millis_cmd = millis(); previous_millis_cmd = millis();
endstops_hit_on_purpose();
break; break;
case 90: // G90 case 90: // G90
relative_mode = false; relative_mode = false;
@ -521,13 +561,14 @@ inline void process_commands()
#ifdef SDSUPPORT #ifdef SDSUPPORT
case 20: // M20 - list SD card case 20: // M20 - list SD card
Serial.println("Begin file list"); SERIAL_PROTOCOLLNPGM("Begin file list");
card.ls(); card.ls();
Serial.println("End file list"); SERIAL_PROTOCOLLNPGM("End file list");
break; break;
case 21: // M21 - init SD card case 21: // M21 - init SD card
card.initsd(); card.initsd();
break; break;
case 22: //M22 - release SD card case 22: //M22 - release SD card
card.release(); card.release();
@ -579,8 +620,9 @@ inline void process_commands()
int sec,min; int sec,min;
min=t/60; min=t/60;
sec=t%60; sec=t%60;
sprintf(time,"echo: time needed %i min, %i sec",min,sec); sprintf(time,"%i min, %i sec",min,sec);
Serial.println(time); SERIAL_ECHO_START;
SERIAL_ECHOLN(time);
LCD_MESSAGE(time); LCD_MESSAGE(time);
} }
break; break;
@ -617,37 +659,30 @@ inline void process_commands()
if (code_seen('S')) setTargetBed(code_value()); if (code_seen('S')) setTargetBed(code_value());
break; break;
case 105: // M105 case 105: // M105
//SERIAL_ECHOLN(freeMemory());
#if (TEMP_0_PIN > -1) || defined (HEATER_USES_AD595) #if (TEMP_0_PIN > -1) || defined (HEATER_USES_AD595)
tt = degHotend0(); SERIAL_PROTOCOLPGM("ok T:");
#endif SERIAL_PROTOCOL( degHotend0());
#if TEMP_1_PIN > -1
bt = degBed();
#endif
#if (TEMP_0_PIN > -1) || defined (HEATER_USES_AD595)
Serial.print("ok T:");
Serial.print(tt);
#if TEMP_1_PIN > -1 #if TEMP_1_PIN > -1
#ifdef PIDTEMP SERIAL_PROTOCOLPGM(" B:");
Serial.print(" B:"); SERIAL_PROTOCOL(degBed());
#if TEMP_1_PIN > -1 #endif //TEMP_1_PIN
Serial.println(bt); #else
#else SERIAL_ERROR_START;
Serial.println(HeaterPower); SERIAL_ERRORLNPGM("No thermistors - no temp");
#endif #endif
#else //not PIDTEMP #ifdef PIDTEMP
Serial.println(); SERIAL_PROTOCOLPGM(" @:");
#endif //PIDTEMP SERIAL_PROTOCOL( HeaterPower);
#else
Serial.println();
#endif //TEMP_1_PIN
#else
SERIAL_ERRORLN("No thermistors - no temp");
#endif #endif
SERIAL_PROTOCOLLN("");
return; return;
break; break;
case 109: case 109:
{// M109 - Wait for extruder heater to reach target. {// M109 - Wait for extruder heater to reach target.
LCD_MESSAGE("Heating..."); LCD_MESSAGEPGM("Heating...");
if (code_seen('S')) setTargetHotend0(code_value()); if (code_seen('S')) setTargetHotend0(code_value());
setWatch(); setWatch();
@ -668,8 +703,8 @@ inline void process_commands()
#endif //TEMP_RESIDENCY_TIME #endif //TEMP_RESIDENCY_TIME
if( (millis() - codenum) > 1000 ) if( (millis() - codenum) > 1000 )
{ //Print Temp Reading every 1 second while heating up/cooling down { //Print Temp Reading every 1 second while heating up/cooling down
Serial.print("T:"); SERIAL_PROTOCOLPGM("T:");
Serial.println( degHotend0() ); SERIAL_PROTOCOLLN( degHotend0() );
codenum = millis(); codenum = millis();
} }
manage_heater(); manage_heater();
@ -685,12 +720,13 @@ inline void process_commands()
} }
#endif //TEMP_RESIDENCY_TIME #endif //TEMP_RESIDENCY_TIME
} }
LCD_MESSAGE("Heating done."); LCD_MESSAGEPGM("Heating done.");
starttime=millis(); starttime=millis();
} }
break; break;
case 190: // M190 - Wait bed for heater to reach target. case 190: // M190 - Wait bed for heater to reach target.
#if TEMP_1_PIN > -1 #if TEMP_1_PIN > -1
LCD_MESSAGEPGM("Bed Heating.");
if (code_seen('S')) setTargetBed(code_value()); if (code_seen('S')) setTargetBed(code_value());
codenum = millis(); codenum = millis();
while(isHeatingBed()) while(isHeatingBed())
@ -698,16 +734,17 @@ inline void process_commands()
if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up.
{ {
float tt=degHotend0(); float tt=degHotend0();
Serial.print("T:"); SERIAL_PROTOCOLPGM("T:");
Serial.println( tt ); SERIAL_PROTOCOLLN(tt );
Serial.print("ok T:"); SERIAL_PROTOCOLPGM("ok T:");
Serial.print( tt ); SERIAL_PROTOCOL(tt );
Serial.print(" B:"); SERIAL_PROTOCOLPGM(" B:");
Serial.println( degBed() ); SERIAL_PROTOCOLLN(degBed() );
codenum = millis(); codenum = millis();
} }
manage_heater(); manage_heater();
} }
LCD_MESSAGEPGM("Bed done.");
#endif #endif
break; break;
@ -752,6 +789,7 @@ inline void process_commands()
else else
{ {
st_synchronize(); st_synchronize();
LCD_MESSAGEPGM("Free move.");
disable_x(); disable_x();
disable_y(); disable_y();
disable_z(); disable_z();
@ -770,53 +808,53 @@ inline void process_commands()
} }
break; break;
case 115: // M115 case 115: // M115
Serial.println("FIRMWARE_NAME:Marlin; Sprinter/grbl mashup for gen6 FIRMWARE_URL:http://www.mendel-parts.com PROTOCOL_VERSION:1.0 MACHINE_TYPE:Mendel EXTRUDER_COUNT:1"); SerialprintPGM("FIRMWARE_NAME:Marlin; Sprinter/grbl mashup for gen6 FIRMWARE_URL:http://www.mendel-parts.com PROTOCOL_VERSION:1.0 MACHINE_TYPE:Mendel EXTRUDER_COUNT:1");
break; break;
case 114: // M114 case 114: // M114
Serial.print("X:"); SERIAL_PROTOCOLPGM("X:");
Serial.print(current_position[X_AXIS]); SERIAL_PROTOCOL(current_position[X_AXIS]);
Serial.print("Y:"); SERIAL_PROTOCOLPGM("Y:");
Serial.print(current_position[Y_AXIS]); SERIAL_PROTOCOL(current_position[Y_AXIS]);
Serial.print("Z:"); SERIAL_PROTOCOLPGM("Z:");
Serial.print(current_position[Z_AXIS]); SERIAL_PROTOCOL(current_position[Z_AXIS]);
Serial.print("E:"); SERIAL_PROTOCOLPGM("E:");
Serial.print(current_position[E_AXIS]); SERIAL_PROTOCOL(current_position[E_AXIS]);
#ifdef DEBUG_STEPS #ifdef DEBUG_STEPS
Serial.print(" Count X:"); SERIAL_PROTOCOLPGM(" Count X:");
Serial.print(float(count_position[X_AXIS])/axis_steps_per_unit[X_AXIS]); SERIAL_PROTOCOL(float(count_position[X_AXIS])/axis_steps_per_unit[X_AXIS]);
Serial.print("Y:"); SERIAL_PROTOCOLPGM("Y:");
Serial.print(float(count_position[Y_AXIS])/axis_steps_per_unit[Y_AXIS]); SERIAL_PROTOCOL(float(count_position[Y_AXIS])/axis_steps_per_unit[Y_AXIS]);
Serial.print("Z:"); SERIAL_PROTOCOLPGM("Z:");
Serial.println(float(count_position[Z_AXIS])/axis_steps_per_unit[Z_AXIS]); SERIAL_PROTOCOL(float(count_position[Z_AXIS])/axis_steps_per_unit[Z_AXIS]);
#endif #endif
Serial.println(""); SERIAL_PROTOCOLLN("");
break; break;
case 119: // M119 case 119: // M119
#if (X_MIN_PIN > -1) #if (X_MIN_PIN > -1)
Serial.print("x_min:"); SERIAL_PROTOCOLPGM("x_min:");
Serial.print((READ(X_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(X_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
#if (X_MAX_PIN > -1) #if (X_MAX_PIN > -1)
Serial.print("x_max:"); SERIAL_PROTOCOLPGM("x_max:");
Serial.print((READ(X_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(X_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
#if (Y_MIN_PIN > -1) #if (Y_MIN_PIN > -1)
Serial.print("y_min:"); SERIAL_PROTOCOLPGM("y_min:");
Serial.print((READ(Y_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(Y_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
#if (Y_MAX_PIN > -1) #if (Y_MAX_PIN > -1)
Serial.print("y_max:"); SERIAL_PROTOCOLPGM("y_max:");
Serial.print((READ(Y_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(Y_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
#if (Z_MIN_PIN > -1) #if (Z_MIN_PIN > -1)
Serial.print("z_min:"); SERIAL_PROTOCOLPGM("z_min:");
Serial.print((READ(Z_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(Z_MIN_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
#if (Z_MAX_PIN > -1) #if (Z_MAX_PIN > -1)
Serial.print("z_max:"); SERIAL_PROTOCOLPGM("z_max:");
Serial.print((READ(Z_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "); SERIAL_PROTOCOL(((READ(Z_MAX_PIN)^ENDSTOPS_INVERTING)?"H ":"L "));
#endif #endif
Serial.println(""); SERIAL_PROTOCOLLN("");
break; break;
//TODO: update for all axis, use for loop //TODO: update for all axis, use for loop
case 201: // M201 case 201: // M201
@ -867,8 +905,28 @@ inline void process_commands()
if(code_seen('P')) Kp = code_value(); if(code_seen('P')) Kp = code_value();
if(code_seen('I')) Ki = code_value()*PID_dT; if(code_seen('I')) Ki = code_value()*PID_dT;
if(code_seen('D')) Kd = code_value()/PID_dT; if(code_seen('D')) Kd = code_value()/PID_dT;
#ifdef PID_ADD_EXTRUSION_RATE
if(code_seen('C')) Kc = code_value();
#endif
SERIAL_PROTOCOL("ok p:");
SERIAL_PROTOCOL(Kp);
SERIAL_PROTOCOL(" i:");
SERIAL_PROTOCOL(Ki/PID_dT);
SERIAL_PROTOCOL(" d:");
SERIAL_PROTOCOL(Kd*PID_dT);
#ifdef PID_ADD_EXTRUSION_RATE
SERIAL_PROTOCOL(" c:");
SERIAL_PROTOCOL(Kc*PID_dT);
#endif
SERIAL_PROTOCOLLN("");
break; break;
#endif //PIDTEMP #endif //PIDTEMP
case 400: // finish all moves
{
st_synchronize();
}
break;
case 500: // Store settings in EEPROM case 500: // Store settings in EEPROM
{ {
StoreSettings(); StoreSettings();
@ -889,9 +947,10 @@ inline void process_commands()
} }
else else
{ {
Serial.print("echo: Unknown command:\""); SERIAL_ECHO_START;
Serial.print(cmdbuffer[bufindr]); SERIAL_ECHOPGM("Unknown command:\"");
Serial.println("\""); SERIAL_ECHO(cmdbuffer[bufindr]);
SERIAL_ECHOLNPGM("\"");
} }
ClearToSend(); ClearToSend();
@ -901,8 +960,8 @@ void FlushSerialRequestResend()
{ {
//char cmdbuffer[bufindr][100]="Resend:"; //char cmdbuffer[bufindr][100]="Resend:";
Serial.flush(); Serial.flush();
Serial.print("Resend:"); SERIAL_PROTOCOLPGM("Resend:");
Serial.println(gcode_LastN + 1); SERIAL_PROTOCOLLN(gcode_LastN + 1);
ClearToSend(); ClearToSend();
} }
@ -913,7 +972,7 @@ void ClearToSend()
if(fromsd[bufindr]) if(fromsd[bufindr])
return; return;
#endif //SDSUPPORT #endif //SDSUPPORT
Serial.println("ok"); SERIAL_PROTOCOLLNPGM("ok");
} }
inline void get_coordinates() inline void get_coordinates()
@ -987,7 +1046,9 @@ void kill()
disable_e(); disable_e();
if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT);
SERIAL_ERRORLN("Printer halted. kill() called !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Printer halted. kill() called !!");
LCD_MESSAGEPGM("KILLED. ");
while(1); // Wait for reset while(1); // Wait for reset
} }

33
Marlin/cardreader.h
Unescape View File

@ -30,8 +30,8 @@ public:
inline void ls() {root.ls();}; inline void ls() {root.ls();};
inline bool eof() { sdpos = file.curPosition();return sdpos>=filesize ;}; inline bool eof() { return sdpos>=filesize ;};
inline char get() { int16_t n = file.read(); return (n!=-1)?(char)n:'\n';}; inline int16_t get() { sdpos = file.curPosition();return (int16_t)file.read();};
inline void setIndex(long index) {sdpos = index;file.seekSet(index);}; inline void setIndex(long index) {sdpos = index;file.seekSet(index);};
public: public:
@ -52,6 +52,35 @@ private:
bool autostart_stilltocheck; //the sd start is delayed, because otherwise the serial cannot answer fast enought to make contact with the hostsoftware. bool autostart_stilltocheck; //the sd start is delayed, because otherwise the serial cannot answer fast enought to make contact with the hostsoftware.
}; };
#else
class CardReader
{
public:
inline CardReader(){};
inline static void initsd(){};
inline static void write_command(char *buf){};
inline static void checkautostart(bool x) {};
inline static void closefile() {};
inline static void release(){};
inline static void startFileprint(){};
inline static void startFilewrite(char *name){};
inline static void pauseSDPrint(){};
inline static void getStatus(){};
inline static void selectFile(char* name){};
inline static void getfilename(const uint8_t nr){};
inline static uint8_t getnrfilenames(){return 0;};
inline static void ls() {};
inline static bool eof() {return true;};
inline static char get() {return 0;};
inline static void setIndex(){};
};
#endif //SDSUPPORT #endif //SDSUPPORT

47
Marlin/cardreader.pde
Unescape View File

@ -29,20 +29,24 @@ void CardReader::initsd()
if (!card.init(SPI_FULL_SPEED,SDSS)) if (!card.init(SPI_FULL_SPEED,SDSS))
{ {
//if (!card.init(SPI_HALF_SPEED,SDSS)) //if (!card.init(SPI_HALF_SPEED,SDSS))
SERIAL_ECHOLN("SD init fail"); SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("SD init fail");
} }
else if (!volume.init(&card)) else if (!volume.init(&card))
{ {
SERIAL_ERRORLN("volume.init failed"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("volume.init failed");
} }
else if (!root.openRoot(&volume)) else if (!root.openRoot(&volume))
{ {
SERIAL_ERRORLN("openRoot failed"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("openRoot failed");
} }
else else
{ {
cardOK = true; cardOK = true;
SERIAL_ECHOLN("SD card ok"); SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("SD card ok");
} }
#endif //SDSS #endif //SDSS
} }
@ -76,17 +80,17 @@ void CardReader::selectFile(char* name)
file.close(); file.close();
if (file.open(&root, name, O_READ)) { if (file.open(&root, name, O_READ)) {
Serial.print("File opened:");
Serial.print(name);
Serial.print(" Size:");
filesize = file.fileSize(); filesize = file.fileSize();
Serial.println(filesize); SERIAL_PROTOCOLPGM("File opened:");
SERIAL_PROTOCOL(name);
SERIAL_PROTOCOLPGM(" Size:");
SERIAL_PROTOCOLLN(filesize);
sdpos = 0; sdpos = 0;
Serial.println("File selected"); SERIAL_PROTOCOLLNPGM("File selected");
} }
else{ else{
Serial.println("file.open failed"); SERIAL_PROTOCOLLNPGM("file.open failed");
} }
} }
} }
@ -101,14 +105,14 @@ void CardReader::startFilewrite(char *name)
if (!file.open(&root, name, O_CREAT | O_APPEND | O_WRITE | O_TRUNC)) if (!file.open(&root, name, O_CREAT | O_APPEND | O_WRITE | O_TRUNC))
{ {
Serial.print("open failed, File: "); SERIAL_PROTOCOLPGM("open failed, File: ");
Serial.print(name); SERIAL_PROTOCOL(name);
Serial.print("."); SERIAL_PROTOCOLLNPGM(".");
} }
else{ else{
saving = true; saving = true;
Serial.print("Writing to file: "); SERIAL_PROTOCOLPGM("Writing to file: ");
Serial.println(name); SERIAL_PROTOCOLLN(name);
} }
} }
} }
@ -116,13 +120,13 @@ void CardReader::startFilewrite(char *name)
void CardReader::getStatus() void CardReader::getStatus()
{ {
if(cardOK){ if(cardOK){
Serial.print("SD printing byte "); SERIAL_PROTOCOLPGM("SD printing byte ");
Serial.print(sdpos); SERIAL_PROTOCOL(sdpos);
Serial.print("/"); SERIAL_PROTOCOLPGM("/");
Serial.println(filesize); SERIAL_PROTOCOLLN(filesize);
} }
else{ else{
Serial.println("Not SD printing"); SERIAL_PROTOCOLLNPGM("Not SD printing");
} }
} }
void CardReader::write_command(char *buf) void CardReader::write_command(char *buf)
@ -143,7 +147,8 @@ void CardReader::write_command(char *buf)
file.write(begin); file.write(begin);
if (file.writeError) if (file.writeError)
{ {
SERIAL_ERRORLN("error writing to file"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("error writing to file");
} }
} }

1386
Marlin/pins.h
Unescape View File

@ -1,694 +1,694 @@
#ifndef PINS_H #ifndef PINS_H
#define PINS_H #define PINS_H
/**************************************************************************************** /****************************************************************************************
* Arduino pin assignment * Arduino pin assignment
* *
* ATMega168 * ATMega168
* +-\/-+ * +-\/-+
* PC6 1| |28 PC5 (AI 5 / D19) * PC6 1| |28 PC5 (AI 5 / D19)
* (D 0) PD0 2| |27 PC4 (AI 4 / D18) * (D 0) PD0 2| |27 PC4 (AI 4 / D18)
* (D 1) PD1 3| |26 PC3 (AI 3 / D17) * (D 1) PD1 3| |26 PC3 (AI 3 / D17)
* (D 2) PD2 4| |25 PC2 (AI 2 / D16) * (D 2) PD2 4| |25 PC2 (AI 2 / D16)
* PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15) * PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15)
* (D 4) PD4 6| |23 PC0 (AI 0 / D14) * (D 4) PD4 6| |23 PC0 (AI 0 / D14)
* VCC 7| |22 GND * VCC 7| |22 GND
* GND 8| |21 AREF * GND 8| |21 AREF
* PB6 9| |20 AVCC * PB6 9| |20 AVCC
* PB7 10| |19 PB5 (D 13) * PB7 10| |19 PB5 (D 13)
* PWM+ (D 5) PD5 11| |18 PB4 (D 12) * PWM+ (D 5) PD5 11| |18 PB4 (D 12)
* PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM * PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM
* (D 7) PD7 13| |16 PB2 (D 10) PWM * (D 7) PD7 13| |16 PB2 (D 10) PWM
* (D 8) PB0 14| |15 PB1 (D 9) PWM * (D 8) PB0 14| |15 PB1 (D 9) PWM
* +----+ * +----+
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 0 #if MOTHERBOARD == 0
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega168__ #ifndef __AVR_ATmega168__
#error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu. #error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu.
#endif #endif
#define X_STEP_PIN 2 #define X_STEP_PIN 2
#define X_DIR_PIN 3 #define X_DIR_PIN 3
#define X_ENABLE_PIN -1 #define X_ENABLE_PIN -1
#define X_MIN_PIN 4 #define X_MIN_PIN 4
#define X_MAX_PIN 9 #define X_MAX_PIN 9
#define Y_STEP_PIN 10 #define Y_STEP_PIN 10
#define Y_DIR_PIN 7 #define Y_DIR_PIN 7
#define Y_ENABLE_PIN -1 #define Y_ENABLE_PIN -1
#define Y_MIN_PIN 8 #define Y_MIN_PIN 8
#define Y_MAX_PIN 13 #define Y_MAX_PIN 13
#define Z_STEP_PIN 19 #define Z_STEP_PIN 19
#define Z_DIR_PIN 18 #define Z_DIR_PIN 18
#define Z_ENABLE_PIN 5 #define Z_ENABLE_PIN 5
#define Z_MIN_PIN 17 #define Z_MIN_PIN 17
#define Z_MAX_PIN 16 #define Z_MAX_PIN 16
#define E_STEP_PIN 11 #define E_STEP_PIN 11
#define E_DIR_PIN 12 #define E_DIR_PIN 12
#define E_ENABLE_PIN -1 #define E_ENABLE_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS -1 #define SDSS -1
#define LED_PIN -1 #define LED_PIN -1
#define FAN_PIN -1 #define FAN_PIN -1
#define PS_ON_PIN 15 #define PS_ON_PIN 15
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 6 #define HEATER_0_PIN 6
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Sanguino/RepRap Motherboard with direct-drive extruders * Sanguino/RepRap Motherboard with direct-drive extruders
* *
* ATMega644P * ATMega644P
* *
* +---\/---+ * +---\/---+
* (D 0) PB0 1| |40 PA0 (AI 0 / D31) * (D 0) PB0 1| |40 PA0 (AI 0 / D31)
* (D 1) PB1 2| |39 PA1 (AI 1 / D30) * (D 1) PB1 2| |39 PA1 (AI 1 / D30)
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
* RST 9| |32 AREF * RST 9| |32 AREF
* VCC 10| |31 GND * VCC 10| |31 GND
* GND 11| |30 AVCC * GND 11| |30 AVCC
* XTAL2 12| |29 PC7 (D 23) * XTAL2 12| |29 PC7 (D 23)
* XTAL1 13| |28 PC6 (D 22) * XTAL1 13| |28 PC6 (D 22)
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
* +--------+ * +--------+
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 1 #if MOTHERBOARD == 1
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif #endif
#define X_STEP_PIN 15 #define X_STEP_PIN 15
#define X_DIR_PIN 18 #define X_DIR_PIN 18
#define X_ENABLE_PIN 19 #define X_ENABLE_PIN 19
#define X_MIN_PIN 20 #define X_MIN_PIN 20
#define X_MAX_PIN 21 #define X_MAX_PIN 21
#define Y_STEP_PIN 23 #define Y_STEP_PIN 23
#define Y_DIR_PIN 22 #define Y_DIR_PIN 22
#define Y_ENABLE_PIN 19 #define Y_ENABLE_PIN 19
#define Y_MIN_PIN 25 #define Y_MIN_PIN 25
#define Y_MAX_PIN 26 #define Y_MAX_PIN 26
#define Z_STEP_PIN 29 #define Z_STEP_PIN 29
#define Z_DIR_PIN 30 #define Z_DIR_PIN 30
#define Z_ENABLE_PIN 31 #define Z_ENABLE_PIN 31
#define Z_MIN_PIN 2 #define Z_MIN_PIN 2
#define Z_MAX_PIN 1 #define Z_MAX_PIN 1
#define E_STEP_PIN 12 #define E_STEP_PIN 12
#define E_DIR_PIN 16 #define E_DIR_PIN 16
#define E_ENABLE_PIN 3 #define E_ENABLE_PIN 3
#define SDPOWER -1 #define SDPOWER -1
#define SDSS -1 #define SDSS -1
#define LED_PIN 0 #define LED_PIN 0
#define FAN_PIN -1 #define FAN_PIN -1
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 14 #define HEATER_0_PIN 14
#define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
#endif #endif
/**************************************************************************************** /****************************************************************************************
* RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---******* * RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---*******
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 2 #if MOTHERBOARD == 2
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif #endif
#define X_STEP_PIN 15 #define X_STEP_PIN 15
#define X_DIR_PIN 18 #define X_DIR_PIN 18
#define X_ENABLE_PIN 19 #define X_ENABLE_PIN 19
#define X_MIN_PIN 20 #define X_MIN_PIN 20
#define X_MAX_PIN 21 #define X_MAX_PIN 21
#define Y_STEP_PIN 23 #define Y_STEP_PIN 23
#define Y_DIR_PIN 22 #define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24 #define Y_ENABLE_PIN 24
#define Y_MIN_PIN 25 #define Y_MIN_PIN 25
#define Y_MAX_PIN 26 #define Y_MAX_PIN 26
#define Z_STEP_PINN 27 #define Z_STEP_PINN 27
#define Z_DIR_PINN 28 #define Z_DIR_PINN 28
#define Z_ENABLE_PIN 29 #define Z_ENABLE_PIN 29
#define Z_MIN_PIN 30 #define Z_MIN_PIN 30
#define Z_MAX_PIN 31 #define Z_MAX_PIN 31
#define E_STEP_PIN 17 #define E_STEP_PIN 17
#define E_DIR_PIN 16 #define E_DIR_PIN 16
#define E_ENABLE_PIN -1 #define E_ENABLE_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 4 #define SDSS 4
#define LED_PIN 0 #define LED_PIN 0
#define SD_CARD_WRITE 2 #define SD_CARD_WRITE 2
#define SD_CARD_DETECT 3 #define SD_CARD_DETECT 3
#define SD_CARD_SELECT 4 #define SD_CARD_SELECT 4
//our RS485 pins //our RS485 pins
#define TX_ENABLE_PIN 12 #define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13 #define RX_ENABLE_PIN 13
//pin for controlling the PSU. //pin for controlling the PSU.
#define PS_ON_PIN 14 #define PS_ON_PIN 14
#define FAN_PIN -1 #define FAN_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN -1 #define HEATER_0_PIN -1
#define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Arduino Mega pin assignment * Arduino Mega pin assignment
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 33 #if MOTHERBOARD == 33
#define MOTHERBOARD 3 #define MOTHERBOARD 3
#define RAMPS_V_1_3 #define RAMPS_V_1_3
#endif #endif
#if MOTHERBOARD == 3 #if MOTHERBOARD == 3
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
//////////////////FIX THIS////////////// //////////////////FIX THIS//////////////
#ifndef __AVR_ATmega1280__ #ifndef __AVR_ATmega1280__
#ifndef __AVR_ATmega2560__ #ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif #endif
#endif #endif
// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1 // uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1
// #define RAMPS_V_1_3 // #define RAMPS_V_1_3
// #define RAMPS_V_1_0 // #define RAMPS_V_1_0
#ifdef RAMPS_V_1_3 #ifdef RAMPS_V_1_3
#define X_STEP_PIN 54 #define X_STEP_PIN 54
#define X_DIR_PIN 55 #define X_DIR_PIN 55
#define X_ENABLE_PIN 38 #define X_ENABLE_PIN 38
#define X_MIN_PIN 3 #define X_MIN_PIN 3
#define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable. #define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable.
#define Y_STEP_PIN 60 #define Y_STEP_PIN 60
#define Y_DIR_PIN 61 #define Y_DIR_PIN 61
#define Y_ENABLE_PIN 56 #define Y_ENABLE_PIN 56
#define Y_MIN_PIN 14 #define Y_MIN_PIN 14
#define Y_MAX_PIN -1 //15 #define Y_MAX_PIN -1 //15
#define Z_STEP_PIN 46 #define Z_STEP_PIN 46
#define Z_DIR_PIN 48 #define Z_DIR_PIN 48
#define Z_ENABLE_PIN 62 #define Z_ENABLE_PIN 62
#define Z_MIN_PIN 18 #define Z_MIN_PIN 18
#define Z_MAX_PIN -1 //19 #define Z_MAX_PIN -1 //19
#define E_STEP_PIN 26 #define E_STEP_PIN 26
#define E_DIR_PIN 28 #define E_DIR_PIN 28
#define E_ENABLE_PIN 24 #define E_ENABLE_PIN 24
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define FAN_PIN 9 #define FAN_PIN 9
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 10 #define HEATER_0_PIN 10
#define HEATER_1_PIN 8 #define HEATER_1_PIN 8
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#define TEMP_0_PIN 13 // ANALOG NUMBERING #define TEMP_0_PIN 13 // ANALOG NUMBERING
#define TEMP_1_PIN 14 // ANALOG NUMBERING #define TEMP_1_PIN 14 // ANALOG NUMBERING
#define TEMP_2_PIN -1 // ANALOG NUMBERING #define TEMP_2_PIN -1 // ANALOG NUMBERING
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default #else // RAMPS_V_1_1 or RAMPS_V_1_2 as default
#define X_STEP_PIN 26 #define X_STEP_PIN 26
#define X_DIR_PIN 28 #define X_DIR_PIN 28
#define X_ENABLE_PIN 24 #define X_ENABLE_PIN 24
#define X_MIN_PIN 3 #define X_MIN_PIN 3
#define X_MAX_PIN -1 //2 #define X_MAX_PIN -1 //2
#define Y_STEP_PIN 38 #define Y_STEP_PIN 38
#define Y_DIR_PIN 40 #define Y_DIR_PIN 40
#define Y_ENABLE_PIN 36 #define Y_ENABLE_PIN 36
#define Y_MIN_PIN 16 #define Y_MIN_PIN 16
#define Y_MAX_PIN -1 //17 #define Y_MAX_PIN -1 //17
#define Z_STEP_PIN 44 #define Z_STEP_PIN 44
#define Z_DIR_PIN 46 #define Z_DIR_PIN 46
#define Z_ENABLE_PIN 42 #define Z_ENABLE_PIN 42
#define Z_MIN_PIN 18 #define Z_MIN_PIN 18
#define Z_MAX_PIN -1 //19 #define Z_MAX_PIN -1 //19
#define E_STEP_PIN 32 #define E_STEP_PIN 32
#define E_DIR_PIN 34 #define E_DIR_PIN 34
#define E_ENABLE_PIN 30 #define E_ENABLE_PIN 30
#define SDPOWER 48 #define SDPOWER 48
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#ifdef RAMPS_V_1_0 // RAMPS_V_1_0 #ifdef RAMPS_V_1_0 // RAMPS_V_1_0
#define HEATER_0_PIN 12 // RAMPS 1.0 #define HEATER_0_PIN 12 // RAMPS 1.0
#define HEATER_1_PIN -1 // RAMPS 1.0 #define HEATER_1_PIN -1 // RAMPS 1.0
#define FAN_PIN 11 // RAMPS 1.0 #define FAN_PIN 11 // RAMPS 1.0
#else // RAMPS_V_1_1 or RAMPS_V_1_2 #else // RAMPS_V_1_1 or RAMPS_V_1_2
#define HEATER_0_PIN 10 // RAMPS 1.1 #define HEATER_0_PIN 10 // RAMPS 1.1
#define HEATER_1_PIN 8 // RAMPS 1.1 #define HEATER_1_PIN 8 // RAMPS 1.1
#define FAN_PIN 9 // RAMPS 1.1 #define FAN_PIN 9 // RAMPS 1.1
#endif #endif
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#endif #endif
// SPI for Max6675 Thermocouple // SPI for Max6675 Thermocouple
#ifndef SDSUPPORT #ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support #define SCK_PIN 52 // these pins are defined in the SD library if building with SD support #define SCK_PIN 52
#define MISO_PIN 50 #define MISO_PIN 50
#define MOSI_PIN 51 #define MOSI_PIN 51
#define MAX6675_SS 53 #define MAX6675_SS 53
#else #else
#define MAX6675_SS 49 #define MAX6675_SS 49
#endif #endif
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Duemilanove w/ ATMega328P pin assignment * Duemilanove w/ ATMega328P pin assignment
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 4 #if MOTHERBOARD == 4
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega328P__ #ifndef __AVR_ATmega328P__
#error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
#endif #endif
#define X_STEP_PIN 19 #define X_STEP_PIN 19
#define X_DIR_PIN 18 #define X_DIR_PIN 18
#define X_ENABLE_PIN -1 #define X_ENABLE_PIN -1
#define X_MIN_PIN 17 #define X_MIN_PIN 17
#define X_MAX_PIN -1 #define X_MAX_PIN -1
#define Y_STEP_PIN 10 #define Y_STEP_PIN 10
#define Y_DIR_PIN 7 #define Y_DIR_PIN 7
#define Y_ENABLE_PIN -1 #define Y_ENABLE_PIN -1
#define Y_MIN_PIN 8 #define Y_MIN_PIN 8
#define Y_MAX_PIN -1 #define Y_MAX_PIN -1
#define Z_STEP_PIN 13 #define Z_STEP_PIN 13
#define Z_DIR_PIN 3 #define Z_DIR_PIN 3
#define Z_ENABLE_PIN 2 #define Z_ENABLE_PIN 2
#define Z_MIN_PIN 4 #define Z_MIN_PIN 4
#define Z_MAX_PIN -1 #define Z_MAX_PIN -1
#define E_STEP_PIN 11 #define E_STEP_PIN 11
#define E_DIR_PIN 12 #define E_DIR_PIN 12
#define E_ENABLE_PIN -1 #define E_ENABLE_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS -1 #define SDSS -1
#define LED_PIN -1 #define LED_PIN -1
#define FAN_PIN 5 #define FAN_PIN 5
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 6 #define HEATER_0_PIN 6
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Gen6 pin assignment * Gen6 pin assignment
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 5 #if MOTHERBOARD == 5
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif #endif
//x axis pins //x axis pins
#define X_STEP_PIN 15 #define X_STEP_PIN 15
#define X_DIR_PIN 18 #define X_DIR_PIN 18
#define X_ENABLE_PIN 19 #define X_ENABLE_PIN 19
#define X_MIN_PIN 20 #define X_MIN_PIN 20
#define X_MAX_PIN -1 #define X_MAX_PIN -1
//y axis pins //y axis pins
#define Y_STEP_PIN 23 #define Y_STEP_PIN 23
#define Y_DIR_PIN 22 #define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24 #define Y_ENABLE_PIN 24
#define Y_MIN_PIN 25 #define Y_MIN_PIN 25
#define Y_MAX_PIN -1 #define Y_MAX_PIN -1
//z axis pins //z axis pins
#define Z_STEP_PIN 27 #define Z_STEP_PIN 27
#define Z_DIR_PIN 28 #define Z_DIR_PIN 28
#define Z_ENABLE_PIN 29 #define Z_ENABLE_PIN 29
#define Z_MIN_PIN 30 #define Z_MIN_PIN 30
#define Z_MAX_PIN -1 #define Z_MAX_PIN -1
//extruder pins //extruder pins
#define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715 #define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715
#define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715 #define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715
#define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715 #define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715
#define TEMP_0_PIN 5 //changed @ rkoeppl 20110410 #define TEMP_0_PIN 5 //changed @ rkoeppl 20110410
#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 #define HEATER_0_PIN 14 //changed @ rkoeppl 20110410
#define HEATER_1_PIN -1 //changed @ rkoeppl 20110410 #define HEATER_1_PIN -1 //changed @ rkoeppl 20110410
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 17 #define SDSS 17
#define LED_PIN -1 //changed @ rkoeppl 20110410 #define LED_PIN -1 //changed @ rkoeppl 20110410
#define TEMP_1_PIN -1 //changed @ rkoeppl 20110410 #define TEMP_1_PIN -1 //changed @ rkoeppl 20110410
#define TEMP_2_PIN -1 #define TEMP_2_PIN -1
#define FAN_PIN -1 //changed @ rkoeppl 20110410 #define FAN_PIN -1 //changed @ rkoeppl 20110410
#define PS_ON_PIN -1 //changed @ rkoeppl 20110410 #define PS_ON_PIN -1 //changed @ rkoeppl 20110410
//our pin for debugging. //our pin for debugging.
#define DEBUG_PIN 0 #define DEBUG_PIN 0
//our RS485 pins //our RS485 pins
#define TX_ENABLE_PIN 12 #define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13 #define RX_ENABLE_PIN 13
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Sanguinololu pin assignment * Sanguinololu pin assignment
* *
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 62 #if MOTHERBOARD == 62
#define MOTHERBOARD 6 #define MOTHERBOARD 6
#define SANGUINOLOLU_V_1_2 #define SANGUINOLOLU_V_1_2
#endif #endif
#if MOTHERBOARD == 6 #if MOTHERBOARD == 6
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif #endif
#define X_STEP_PIN 15 #define X_STEP_PIN 15
#define X_DIR_PIN 21 #define X_DIR_PIN 21
#define X_MIN_PIN 18 #define X_MIN_PIN 18
#define X_MAX_PIN -2 #define X_MAX_PIN -2
#define Y_STEP_PIN 22 #define Y_STEP_PIN 22
#define Y_DIR_PIN 23 #define Y_DIR_PIN 23
#define Y_MIN_PIN 19 #define Y_MIN_PIN 19
#define Y_MAX_PIN -1 #define Y_MAX_PIN -1
#define Z_STEP_PIN 3 #define Z_STEP_PIN 3
#define Z_DIR_PIN 2 #define Z_DIR_PIN 2
#define Z_MIN_PIN 20 #define Z_MIN_PIN 20
#define Z_MAX_PIN -1 #define Z_MAX_PIN -1
#define E_STEP_PIN 1 #define E_STEP_PIN 1
#define E_DIR_PIN 0 #define E_DIR_PIN 0
#define LED_PIN -1 #define LED_PIN -1
#define FAN_PIN -1 #define FAN_PIN -1
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 13 // (extruder) #define HEATER_0_PIN 13 // (extruder)
#ifdef SANGUINOLOLU_V_1_2 #ifdef SANGUINOLOLU_V_1_2
#define HEATER_1_PIN 12 // (bed) #define HEATER_1_PIN 12 // (bed)
#define X_ENABLE_PIN 14 #define X_ENABLE_PIN 14
#define Y_ENABLE_PIN 14 #define Y_ENABLE_PIN 14
#define Z_ENABLE_PIN 26 #define Z_ENABLE_PIN 26
#define E_ENABLE_PIN 14 #define E_ENABLE_PIN 14
#else #else
#define HEATER_1_PIN 14 // (bed) #define HEATER_1_PIN 14 // (bed)
#define X_ENABLE_PIN -1 #define X_ENABLE_PIN -1
#define Y_ENABLE_PIN -1 #define Y_ENABLE_PIN -1
#define Z_ENABLE_PIN -1 #define Z_ENABLE_PIN -1
#define E_ENABLE_PIN -1 #define E_ENABLE_PIN -1
#endif #endif
#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) #define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) #define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define TEMP_2_PIN -1 #define TEMP_2_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 31 #define SDSS 31
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#endif #endif
#if MOTHERBOARD == 7 #if MOTHERBOARD == 7
#define KNOWN_BOARD #define KNOWN_BOARD
/***************************************************************** /*****************************************************************
* Ultimaker pin assignment * Ultimaker pin assignment
******************************************************************/ ******************************************************************/
#ifndef __AVR_ATmega1280__ #ifndef __AVR_ATmega1280__
#ifndef __AVR_ATmega2560__ #ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif #endif
#endif #endif
#define X_STEP_PIN 25 #define X_STEP_PIN 25
#define X_DIR_PIN 23 #define X_DIR_PIN 23
#define X_MIN_PIN 22 #define X_MIN_PIN 22
#define X_MAX_PIN 24 #define X_MAX_PIN 24
#define X_ENABLE_PIN 27 #define X_ENABLE_PIN 27
#define Y_STEP_PIN 31 #define Y_STEP_PIN 31
#define Y_DIR_PIN 33 #define Y_DIR_PIN 33
#define Y_MIN_PIN 26 #define Y_MIN_PIN 26
#define Y_MAX_PIN 28 #define Y_MAX_PIN 28
#define Y_ENABLE_PIN 29 #define Y_ENABLE_PIN 29
#define Z_STEP_PIN 37 #define Z_STEP_PIN 37
#define Z_DIR_PIN 39 #define Z_DIR_PIN 39
#define Z_MIN_PIN 30 #define Z_MIN_PIN 30
#define Z_MAX_PIN 32 #define Z_MAX_PIN 32
#define Z_ENABLE_PIN 35 #define Z_ENABLE_PIN 35
#define HEATER_1_PIN 4 #define HEATER_1_PIN 4
#define TEMP_1_PIN 11 #define TEMP_1_PIN 11
#define EXTRUDER_0_STEP_PIN 43 #define EXTRUDER_0_STEP_PIN 43
#define EXTRUDER_0_DIR_PIN 45 #define EXTRUDER_0_DIR_PIN 45
#define EXTRUDER_0_ENABLE_PIN 41 #define EXTRUDER_0_ENABLE_PIN 41
#define HEATER_0_PIN 2 #define HEATER_0_PIN 2
#define TEMP_0_PIN 8 #define TEMP_0_PIN 8
#define EXTRUDER_1_STEP_PIN 49 #define EXTRUDER_1_STEP_PIN 49
#define EXTRUDER_1_DIR_PIN 47 #define EXTRUDER_1_DIR_PIN 47
#define EXTRUDER_1_ENABLE_PIN 51 #define EXTRUDER_1_ENABLE_PIN 51
#define EXTRUDER_1_HEATER_PIN 3 #define EXTRUDER_1_HEATER_PIN 3
#define EXTRUDER_1_TEMPERATURE_PIN 10 #define EXTRUDER_1_TEMPERATURE_PIN 10
#define HEATER_2_PIN 51 #define HEATER_2_PIN 51
#define TEMP_2_PIN 3 #define TEMP_2_PIN 3
#define E_STEP_PIN EXTRUDER_0_STEP_PIN #define E_STEP_PIN EXTRUDER_0_STEP_PIN
#define E_DIR_PIN EXTRUDER_0_DIR_PIN #define E_DIR_PIN EXTRUDER_0_DIR_PIN
#define E_ENABLE_PIN EXTRUDER_0_ENABLE_PIN #define E_ENABLE_PIN EXTRUDER_0_ENABLE_PIN
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 53 #define SDSS 53
#define LED_PIN 13 #define LED_PIN 13
#define FAN_PIN 7 #define FAN_PIN 7
#define PS_ON_PIN 12 #define PS_ON_PIN 12
#define KILL_PIN -1 #define KILL_PIN -1
#ifdef ULTRA_LCD #ifdef ULTRA_LCD
#ifdef NEWPANEL #ifdef NEWPANEL
//arduino pin witch triggers an piezzo beeper //arduino pin witch triggers an piezzo beeper
#define BEEPER 18 #define BEEPER 18
#define LCD_PINS_RS 20 #define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17 #define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16 #define LCD_PINS_D4 16
#define LCD_PINS_D5 21 #define LCD_PINS_D5 21
#define LCD_PINS_D6 5 #define LCD_PINS_D6 5
#define LCD_PINS_D7 6 #define LCD_PINS_D7 6
//buttons are directly attached //buttons are directly attached
#define BTN_EN1 40 #define BTN_EN1 40
#define BTN_EN2 42 #define BTN_EN2 42
#define BTN_ENC 19 //the click #define BTN_ENC 19 //the click
#define BLEN_C 2 #define BLEN_C 2
#define BLEN_B 1 #define BLEN_B 1
#define BLEN_A 0 #define BLEN_A 0
#define SDCARDDETECT 38 #define SDCARDDETECT 38
//encoder rotation values //encoder rotation values
#define encrot0 0 #define encrot0 0
#define encrot1 2 #define encrot1 2
#define encrot2 3 #define encrot2 3
#define encrot3 1 #define encrot3 1
#else //old style panel with shift register #else //old style panel with shift register
//arduino pin witch triggers an piezzo beeper //arduino pin witch triggers an piezzo beeper
#define BEEPER 18 #define BEEPER 18
//buttons are attached to a shift register //buttons are attached to a shift register
#define SHIFT_CLK 38 #define SHIFT_CLK 38
#define SHIFT_LD 42 #define SHIFT_LD 42
#define SHIFT_OUT 40 #define SHIFT_OUT 40
#define SHIFT_EN 17 #define SHIFT_EN 17
#define LCD_PINS_RS 16 #define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 5 #define LCD_PINS_ENABLE 5
#define LCD_PINS_D4 6 #define LCD_PINS_D4 6
#define LCD_PINS_D5 21 #define LCD_PINS_D5 21
#define LCD_PINS_D6 20 #define LCD_PINS_D6 20
#define LCD_PINS_D7 19 #define LCD_PINS_D7 19
//encoder rotation values //encoder rotation values
#define encrot0 0 #define encrot0 0
#define encrot1 2 #define encrot1 2
#define encrot2 3 #define encrot2 3
#define encrot3 1 #define encrot3 1
//bits in the shift register that carry the buttons for: //bits in the shift register that carry the buttons for:
// left up center down right red // left up center down right red
#define BL_LE 7 #define BL_LE 7
#define BL_UP 6 #define BL_UP 6
#define BL_MI 5 #define BL_MI 5
#define BL_DW 4 #define BL_DW 4
#define BL_RI 3 #define BL_RI 3
#define BL_ST 2 #define BL_ST 2
#define BLEN_B 1 #define BLEN_B 1
#define BLEN_A 0 #define BLEN_A 0
#endif #endif
#endif //ULTRA_LCD #endif //ULTRA_LCD
#endif #endif
/**************************************************************************************** /****************************************************************************************
* Teensylu 0.7 pin assingments (ATMEGA90USB) * Teensylu 0.7 pin assingments (ATMEGA90USB)
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE! * Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
****************************************************************************************/ ****************************************************************************************/
#if MOTHERBOARD == 8 #if MOTHERBOARD == 8
#define MOTHERBOARD 8 #define MOTHERBOARD 8
#define KNOWN_BOARD 1 #define KNOWN_BOARD 1
#define X_STEP_PIN 0 #define X_STEP_PIN 0
#define X_DIR_PIN 1 #define X_DIR_PIN 1
#define X_ENABLE_PIN 39 #define X_ENABLE_PIN 39
#define X_MIN_PIN 13 #define X_MIN_PIN 13
#define X_MAX_PIN -1 #define X_MAX_PIN -1
#define Y_STEP_PIN 2 #define Y_STEP_PIN 2
#define Y_DIR_PIN 3 #define Y_DIR_PIN 3
#define Y_ENABLE_PIN 38 #define Y_ENABLE_PIN 38
#define Y_MIN_PIN 14 #define Y_MIN_PIN 14
#define Y_MAX_PIN -1 #define Y_MAX_PIN -1
#define Z_STEP_PIN 4 #define Z_STEP_PIN 4
#define Z_DIR_PIN 5 #define Z_DIR_PIN 5
#define Z_ENABLE_PIN 23 #define Z_ENABLE_PIN 23
#define Z_MIN_PIN 15 #define Z_MIN_PIN 15
#define Z_MAX_PIN -1 #define Z_MAX_PIN -1
#define E_STEP_PIN 6 #define E_STEP_PIN 6
#define E_DIR_PIN 7 #define E_DIR_PIN 7
#define E_ENABLE_PIN 19 #define E_ENABLE_PIN 19
#define HEATER_0_PIN 21 // Extruder #define HEATER_0_PIN 21 // Extruder
#define HEATER_1_PIN 20 // Bed #define HEATER_1_PIN 20 // Bed
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#define FAN_PIN 22 // Fan #define FAN_PIN 22 // Fan
#define TEMP_0_PIN 7 // Extruder #define TEMP_0_PIN 7 // Extruder
#define TEMP_1_PIN 6 // Bed #define TEMP_1_PIN 6 // Bed
#define TEMP_2_PIN -1 #define TEMP_2_PIN -1
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 8 #define SDSS 8
#define LED_PIN -1 #define LED_PIN -1
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define ALARM_PIN -1 #define ALARM_PIN -1
#ifndef SDSUPPORT #ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support // these pins are defined in the SD library if building with SD support
#define SCK_PIN 9 #define SCK_PIN 9
#define MISO_PIN 11 #define MISO_PIN 11
#define MOSI_PIN 10 #define MOSI_PIN 10
#endif #endif
#endif #endif
#ifndef KNOWN_BOARD #ifndef KNOWN_BOARD
#error Unknown MOTHERBOARD value in configuration.h #error Unknown MOTHERBOARD value in configuration.h
#endif #endif
//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! //List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, HEATER_2_PIN, FAN_PIN, TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN} #define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, HEATER_2_PIN, FAN_PIN, TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN}
#endif #endif

38
Marlin/planner.cpp
Unescape View File

@ -86,6 +86,10 @@ long position[4]; //rescaled from extern when axis_steps_per_unit are changed
static float previous_speed[4]; // Speed of previous path line segment static float previous_speed[4]; // Speed of previous path line segment
static float previous_nominal_speed; // Nominal speed of previous path line segment static float previous_nominal_speed; // Nominal speed of previous path line segment
#ifdef AUTOTEMP
float high_e_speed=0;
#endif
//=========================================================================== //===========================================================================
//=============================private variables ============================ //=============================private variables ============================
@ -372,6 +376,34 @@ block_t *plan_get_current_block() {
return(block); return(block);
} }
#ifdef AUTOTEMP
void getHighESpeed()
{
if(degTargetHotend0()+2<AUTOTEMP_MIN) //probably temperature set to zero.
return; //do nothing
float high=0;
char block_index = block_buffer_tail;
while(block_index != block_buffer_head) {
float se=block_buffer[block_index].speed_e;
if(se>high)
{
high=se;
}
block_index = (block_index+1) & (BLOCK_BUFFER_SIZE - 1);
}
high_e_speed=high*axis_steps_per_unit[E_AXIS]/(1000000.0); //so it is independent of the esteps/mm. before
float g=AUTOTEMP_MIN+high_e_speed*AUTOTEMP_FACTOR;
float t=constrain(AUTOTEMP_MIN,g,AUTOTEMP_MAX);
setTargetHotend0(t);
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("highe",high_e_speed);
SERIAL_ECHOPAIR(" t",t);
SERIAL_ECHOLN("");
}
#endif
void check_axes_activity() { void check_axes_activity() {
unsigned char x_active = 0; unsigned char x_active = 0;
unsigned char y_active = 0; unsigned char y_active = 0;
@ -686,7 +718,9 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
memcpy(position, target, sizeof(target)); // position[] = target[] memcpy(position, target, sizeof(target)); // position[] = target[]
planner_recalculate(); planner_recalculate();
#ifdef AUTOTEMP
getHighESpeed();
#endif
st_wake_up(); st_wake_up();
} }
@ -702,4 +736,4 @@ void plan_set_position(const float &x, const float &y, const float &z, const flo
previous_speed[2] = 0.0; previous_speed[2] = 0.0;
previous_speed[3] = 0.0; previous_speed[3] = 0.0;
} }

6
Marlin/planner.h
Unescape View File

@ -92,5 +92,7 @@ extern float max_xy_jerk; //speed than can be stopped at once, if i understand c
extern float max_z_jerk; extern float max_z_jerk;
extern float mintravelfeedrate; extern float mintravelfeedrate;
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS]; extern unsigned long axis_steps_per_sqr_second[NUM_AXIS];
#ifdef AUTOTEMP
#endif extern float high_e_speed;
#endif
#endif

60
Marlin/stepper.cpp
Unescape View File

@ -33,12 +33,14 @@
#include "speed_lookuptable.h" #include "speed_lookuptable.h"
//=========================================================================== //===========================================================================
//=============================public variables ============================ //=============================public variables ============================
//=========================================================================== //===========================================================================
block_t *current_block; // A pointer to the block currently being traced block_t *current_block; // A pointer to the block currently being traced
//=========================================================================== //===========================================================================
//=============================private variables ============================ //=============================private variables ============================
//=========================================================================== //===========================================================================
@ -62,7 +64,9 @@ static long acceleration_time, deceleration_time;
static unsigned short acc_step_rate; // needed for deccelaration start point static unsigned short acc_step_rate; // needed for deccelaration start point
static char step_loops; static char step_loops;
volatile long endstops_trigsteps[3]={0,0,0};
volatile long endstops_stepsTotal,endstops_stepsDone;
static volatile bool endstops_hit=false;
// if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer. // if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer.
// for debugging purposes only, should be disabled by default // for debugging purposes only, should be disabled by default
@ -152,9 +156,49 @@ asm volatile ( \
#define DISABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 &= ~(1<<OCIE1A) #define DISABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 &= ~(1<<OCIE1A)
void endstops_triggered(const unsigned long &stepstaken)
{
//this will only work if there is no bufferig
//however, if you perform a move at which the endstops should be triggered, and wait for it to complete, i.e. by blocking command, it should work
//yes, it uses floats, but: if endstops are triggered, thats hopefully not critical anymore anyways.
//endstops_triggerpos;
if(endstops_hit) //hitting a second time while the first hit is not reported
return;
if(current_block == NULL)
return;
endstops_stepsTotal=current_block->step_event_count;
endstops_stepsDone=stepstaken;
endstops_trigsteps[0]=current_block->steps_x;
endstops_trigsteps[1]=current_block->steps_y;
endstops_trigsteps[2]=current_block->steps_z;
endstops_hit=true;
}
void checkHitEndstops()
{
if( !endstops_hit)
return;
float endstops_triggerpos[3]={0,0,0};
float ratiodone=endstops_stepsDone/float(endstops_stepsTotal); //ratio of current_block thas was performed
endstops_triggerpos[0]=current_position[0]-(endstops_trigsteps[0]*ratiodone)/float(axis_steps_per_unit[0]);
endstops_triggerpos[1]=current_position[1]-(endstops_trigsteps[1]*ratiodone)/float(axis_steps_per_unit[1]);
endstops_triggerpos[2]=current_position[2]-(endstops_trigsteps[2]*ratiodone)/float(axis_steps_per_unit[2]);
SERIAL_ECHO_START;
SERIAL_ECHOPGM("endstops hit: ");
SERIAL_ECHOPAIR(" X:",endstops_triggerpos[0]);
SERIAL_ECHOPAIR(" Y:",endstops_triggerpos[1]);
SERIAL_ECHOPAIR(" Z:",endstops_triggerpos[2]);
SERIAL_ECHOLN("");
endstops_hit=false;
}
void endstops_hit_on_purpose()
{
endstops_hit=false;
}
// __________________________ // __________________________
// /| |\ _________________ ^ // /| |\ _________________ ^
@ -232,7 +276,9 @@ inline void trapezoid_generator_reset() {
ISR(TIMER1_COMPA_vect) ISR(TIMER1_COMPA_vect)
{ {
if(busy){ if(busy){
/* SERIAL_ERRORLN(*(unsigned short *)OCR1A<< " ISR overtaking itself.");*/ SERIAL_ERROR_START
SERIAL_ERROR(*(unsigned short *)OCR1A);
SERIAL_ERRORLNPGM(" ISR overtaking itself.");
return; return;
} // The busy-flag is used to avoid reentering this interrupt } // The busy-flag is used to avoid reentering this interrupt
@ -294,6 +340,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if X_MIN_PIN > -1 #if X_MIN_PIN > -1
if(READ(X_MIN_PIN) != ENDSTOPS_INVERTING) { if(READ(X_MIN_PIN) != ENDSTOPS_INVERTING) {
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -305,6 +352,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if X_MAX_PIN > -1 #if X_MAX_PIN > -1
if((READ(X_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_x >0)){ if((READ(X_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_x >0)){
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -317,6 +365,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if Y_MIN_PIN > -1 #if Y_MIN_PIN > -1
if(READ(Y_MIN_PIN) != ENDSTOPS_INVERTING) { if(READ(Y_MIN_PIN) != ENDSTOPS_INVERTING) {
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -328,6 +377,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if Y_MAX_PIN > -1 #if Y_MAX_PIN > -1
if((READ(Y_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_y >0)){ if((READ(Y_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_y >0)){
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -340,6 +390,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if Z_MIN_PIN > -1 #if Z_MIN_PIN > -1
if(READ(Z_MIN_PIN) != ENDSTOPS_INVERTING) { if(READ(Z_MIN_PIN) != ENDSTOPS_INVERTING) {
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -351,6 +402,7 @@ ISR(TIMER1_COMPA_vect)
#endif #endif
#if Z_MAX_PIN > -1 #if Z_MAX_PIN > -1
if((READ(Z_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_z >0)){ if((READ(Z_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_z >0)){
endstops_triggered(step_events_completed);
step_events_completed = current_block->step_event_count; step_events_completed = current_block->step_event_count;
} }
#endif #endif
@ -614,4 +666,4 @@ void st_synchronize()
manage_inactivity(1); manage_inactivity(1);
LCD_STATUS; LCD_STATUS;
} }
} }

7
Marlin/stepper.h
Unescape View File

@ -39,6 +39,13 @@ void st_wake_up();
extern volatile long count_position[NUM_AXIS]; extern volatile long count_position[NUM_AXIS];
extern volatile int count_direction[NUM_AXIS]; extern volatile int count_direction[NUM_AXIS];
#endif #endif
void checkHitEndstops(); //call from somwhere to create an serial error message with the locations the endstops where hit, in case they were triggered
void endstops_hit_on_purpose(); //avoid creation of the message, i.e. after homeing and before a routine call of checkHitEndstops();
extern block_t *current_block; // A pointer to the block currently being traced extern block_t *current_block; // A pointer to the block currently being traced
#endif #endif

84
Marlin/streaming.h
Unescape View File

@ -1,84 +0,0 @@
/*
Streaming.h - Arduino library for supporting the << streaming operator
Copyright (c) 2010 Mikal Hart. All rights reserved.
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef ARDUINO_STREAMING
#define ARDUINO_STREAMING
//#include <WProgram.h>
#define STREAMING_LIBRARY_VERSION 4
// Generic template
template<class T>
inline Print &operator <<(Print &stream, T arg)
{ stream.print(arg); return stream; }
struct _BASED
{
long val;
int base;
_BASED(long v, int b): val(v), base(b)
{}
};
#define _HEX(a) _BASED(a, HEX)
#define _DEC(a) _BASED(a, DEC)
#define _OCT(a) _BASED(a, OCT)
#define _BIN(a) _BASED(a, BIN)
#define _BYTE(a) _BASED(a, BYTE)
// Specialization for class _BASED
// Thanks to Arduino forum user Ben Combee who suggested this
// clever technique to allow for expressions like
// Serial << _HEX(a);
inline Print &operator <<(Print &obj, const _BASED &arg)
{ obj.print(arg.val, arg.base); return obj; }
#if ARDUINO >= 18
// Specialization for class _FLOAT
// Thanks to Michael Margolis for suggesting a way
// to accommodate Arduino 0018's floating point precision
// feature like this:
// Serial << _FLOAT(gps_latitude, 6); // 6 digits of precision
struct _FLOAT
{
float val;
int digits;
_FLOAT(double v, int d): val(v), digits(d)
{}
};
inline Print &operator <<(Print &obj, const _FLOAT &arg)
{ obj.print(arg.val, arg.digits); return obj; }
#endif
// Specialization for enum _EndLineCode
// Thanks to Arduino forum user Paul V. who suggested this
// clever technique to allow for expressions like
// Serial << "Hello!" << endl;
enum _EndLineCode { endl };
inline Print &operator <<(Print &obj, _EndLineCode arg)
{ obj.println(); return obj; }
#endif

30
Marlin/temperature.cpp
Unescape View File

@ -35,7 +35,6 @@
#include "pins.h" #include "pins.h"
#include "Marlin.h" #include "Marlin.h"
#include "ultralcd.h" #include "ultralcd.h"
#include "streaming.h"
#include "temperature.h" #include "temperature.h"
#include "watchdog.h" #include "watchdog.h"
@ -160,11 +159,13 @@ void manage_heater()
// pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high // pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high
// #endif // #endif
pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX); pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX);
} }
#endif //PID_OPENLOOP #endif //PID_OPENLOOP
#ifdef PID_DEBUG #ifdef PID_DEBUG
SERIAL_ECHOLN(" PIDDEBUG Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm<<" iTerm "<<iTerm<<" dTerm "<<dTerm); //SERIAL_ECHOLN(" PIDDEBUG Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm<<" iTerm "<<iTerm<<" dTerm "<<dTerm);
#endif //PID_DEBUG #endif //PID_DEBUG
HeaterPower=pid_output;
analogWrite(HEATER_0_PIN, pid_output); analogWrite(HEATER_0_PIN, pid_output);
#endif //PIDTEMP #endif //PIDTEMP
@ -253,7 +254,7 @@ int temp2analogBed(int celsius) {
return (1023 * OVERSAMPLENR) - raw; return (1023 * OVERSAMPLENR) - raw;
#elif defined BED_USES_AD595 #elif defined BED_USES_AD595
return celsius * (1024.0 / (5.0 * 100.0) ) * OVERSAMPLENR; return lround(celsius * (1024.0 * OVERSAMPLENR/ (5.0 * 100.0) ) );
#endif #endif
} }
@ -464,7 +465,8 @@ ISR(TIMER0_COMPB_vect)
temp_count++; temp_count++;
break; break;
default: default:
SERIAL_ERRORLN("Temp measurement error!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temp measurement error!");
break; break;
} }
@ -498,7 +500,8 @@ ISR(TIMER0_COMPB_vect)
if(current_raw[TEMPSENSOR_HOTEND_0] >= maxttemp_0) { if(current_raw[TEMPSENSOR_HOTEND_0] >= maxttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0; target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0); analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MAXTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 0 switched off. MAXTEMP triggered !!");
kill(); kill();
} }
#endif #endif
@ -509,7 +512,8 @@ ISR(TIMER0_COMPB_vect)
target_raw[TEMPSENSOR_HOTEND_1] = 0; target_raw[TEMPSENSOR_HOTEND_1] = 0;
if(current_raw[2] >= maxttemp_1) { if(current_raw[2] >= maxttemp_1) {
analogWrite(HEATER_2_PIN, 0); analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MAXTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 1 switched off. MAXTEMP triggered !!");
kill() kill()
} }
#endif #endif
@ -520,7 +524,8 @@ ISR(TIMER0_COMPB_vect)
if(current_raw[TEMPSENSOR_HOTEND_0] <= minttemp_0) { if(current_raw[TEMPSENSOR_HOTEND_0] <= minttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0; target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0); analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MINTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 0 switched off. MINTEMP triggered !!");
kill(); kill();
} }
#endif #endif
@ -531,7 +536,8 @@ ISR(TIMER0_COMPB_vect)
if(current_raw[TEMPSENSOR_HOTEND_1] <= minttemp_1) { if(current_raw[TEMPSENSOR_HOTEND_1] <= minttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0; target_raw[TEMPSENSOR_HOTEND_1] = 0;
analogWrite(HEATER_2_PIN, 0); analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MINTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 1 switched off. MINTEMP triggered !!");
kill(); kill();
} }
#endif #endif
@ -542,7 +548,8 @@ ISR(TIMER0_COMPB_vect)
if(current_raw[1] <= bed_minttemp) { if(current_raw[1] <= bed_minttemp) {
target_raw[1] = 0; target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0); WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperatur heated bed switched off. MINTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperatur heated bed switched off. MINTEMP triggered !!");
kill(); kill();
} }
#endif #endif
@ -553,7 +560,8 @@ ISR(TIMER0_COMPB_vect)
if(current_raw[1] >= bed_maxttemp) { if(current_raw[1] >= bed_maxttemp) {
target_raw[1] = 0; target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0); WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperature heated bed switched off. MAXTEMP triggered !!"); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature heated bed switched off. MAXTEMP triggered !!");
kill(); kill();
} }
#endif #endif
@ -561,4 +569,4 @@ ISR(TIMER0_COMPB_vect)
} }
} }

1
Marlin/ultralcd.h
Unescape View File

@ -83,6 +83,7 @@
#define LCD_MESSAGE(x) lcd_status(x); #define LCD_MESSAGE(x) lcd_status(x);
#define LCD_MESSAGEPGM(x) lcd_statuspgm(PSTR(x));
#define LCD_STATUS lcd_status() #define LCD_STATUS lcd_status()
#else //no lcd #else //no lcd
#define LCD_STATUS #define LCD_STATUS

142
Marlin/ultralcd.pde
Unescape View File

@ -42,6 +42,19 @@ static long previous_millis_buttons=0;
static MainMenu menu; static MainMenu menu;
#include <avr/pgmspace.h>
void lcdProgMemprint(const char *str)
{
char ch=pgm_read_byte(str);
while(ch)
{
lcd.print(ch);
ch=pgm_read_byte(++str);
}
}
#define lcdprintPGM(x) lcdProgMemprint(PSTR(x))
//=========================================================================== //===========================================================================
//=============================functions ============================ //=============================functions ============================
@ -54,6 +67,20 @@ void lcd_status(const char* message)
strncpy(messagetext,message,LCD_WIDTH); strncpy(messagetext,message,LCD_WIDTH);
} }
void lcd_statuspgm(const char* message)
{
char ch=pgm_read_byte(message);
char *target=messagetext;
uint8_t cnt=0;
while(ch &&cnt<LCD_WIDTH)
{
*target=ch;
target++;
cnt++;
ch=pgm_read_byte(++message);
}
}
inline void clear() inline void clear()
{ {
lcd.clear(); lcd.clear();
@ -92,7 +119,7 @@ void lcd_init()
lcd.createChar(2,Thermometer); lcd.createChar(2,Thermometer);
lcd.createChar(3,uplevel); lcd.createChar(3,uplevel);
lcd.createChar(4,refresh); lcd.createChar(4,refresh);
LCD_MESSAGE(fillto(LCD_WIDTH,"UltiMarlin ready.")); LCD_MESSAGEPGM("UltiMarlin ready.");
} }
@ -264,9 +291,9 @@ void MainMenu::showStatus()
feedmultiplychanged=false; feedmultiplychanged=false;
encoderpos=feedmultiply; encoderpos=feedmultiply;
clear(); clear();
lcd.setCursor(0,0);lcd.print("\002123/567\001 "); lcd.setCursor(0,0);lcdprintPGM("\002123/567\001 ");
#if defined BED_USES_THERMISTOR || defined BED_USES_AD595 #if defined BED_USES_THERMISTOR || defined BED_USES_AD595
lcd.setCursor(10,0);lcd.print("B123/567\001 "); lcd.setCursor(10,0);lcdprintPGM("B123/567\001 ");
#endif #endif
} }
@ -311,7 +338,7 @@ void MainMenu::showStatus()
if(starttime!=oldtime) if(starttime!=oldtime)
{ {
lcd.print(itostr2(time/60));lcd.print("h ");lcd.print(itostr2(time%60));lcd.print("m"); lcd.print(itostr2(time/60));lcdprintPGM("h ");lcd.print(itostr2(time%60));lcdprintPGM("m");
oldtime=time; oldtime=time;
} }
} }
@ -320,7 +347,7 @@ void MainMenu::showStatus()
if((currentz!=oldzpos)||force_lcd_update) if((currentz!=oldzpos)||force_lcd_update)
{ {
lcd.setCursor(10,1); lcd.setCursor(10,1);
lcd.print("Z:");lcd.print(itostr31(currentz)); lcdprintPGM("Z:");lcd.print(itostr31(currentz));
oldzpos=currentz; oldzpos=currentz;
} }
static int oldfeedmultiply=0; static int oldfeedmultiply=0;
@ -339,7 +366,7 @@ void MainMenu::showStatus()
{ {
oldfeedmultiply=curfeedmultiply; oldfeedmultiply=curfeedmultiply;
lcd.setCursor(0,2); lcd.setCursor(0,2);
lcd.print(itostr3(curfeedmultiply));lcd.print("% "); lcd.print(itostr3(curfeedmultiply));lcdprintPGM("% ");
} }
if(messagetext[0]!='\0') if(messagetext[0]!='\0')
{ {
@ -353,9 +380,9 @@ void MainMenu::showStatus()
if(force_lcd_update) //initial display of content if(force_lcd_update) //initial display of content
{ {
encoderpos=feedmultiply; encoderpos=feedmultiply;
lcd.setCursor(0,0);lcd.print("\002123/567\001 "); lcd.setCursor(0,0);lcdprintPGM("\002123/567\001 ");
#if defined BED_USES_THERMISTOR || defined BED_USES_AD595 #if defined BED_USES_THERMISTOR || defined BED_USES_AD595
lcd.setCursor(10,0);lcd.print("B123/567\001 "); lcd.setCursor(10,0);lcdprintPGM("B123/567\001 ");
#endif #endif
} }
@ -405,7 +432,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Prepare"); lcd.setCursor(0,line);lcdprintPGM(" Prepare");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -418,7 +445,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Auto Home"); lcd.setCursor(0,line);lcdprintPGM(" Auto Home");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -431,7 +458,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Set Origin"); lcd.setCursor(0,line);lcdprintPGM(" Set Origin");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
@ -445,7 +472,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Preheat"); lcd.setCursor(0,line);lcdprintPGM(" Preheat");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -458,7 +485,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Extrude"); lcd.setCursor(0,line);lcdprintPGM(" Extrude");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -472,7 +499,7 @@ void MainMenu::showPrepare()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Disable Steppers"); lcd.setCursor(0,line);lcdprintPGM(" Disable Steppers");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -541,7 +568,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Control"); lcd.setCursor(0,line);lcdprintPGM(" Control");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -554,7 +581,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" \002Nozzle:"); lcd.setCursor(0,line);lcdprintPGM(" \002Nozzle:");
lcd.setCursor(13,line);lcd.print(ftostr3(intround(degHotend0()))); lcd.setCursor(13,line);lcd.print(ftostr3(intround(degHotend0())));
} }
@ -588,7 +615,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Fan speed:"); lcd.setCursor(0,line);lcdprintPGM(" Fan speed:");
lcd.setCursor(13,line);lcd.print(ftostr3(fanpwm)); lcd.setCursor(13,line);lcd.print(ftostr3(fanpwm));
} }
@ -625,8 +652,8 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Acc:"); lcd.setCursor(0,line);lcdprintPGM(" Acc:");
lcd.setCursor(13,line);lcd.print(itostr3(acceleration/100));lcd.print("00"); lcd.setCursor(13,line);lcd.print(itostr3(acceleration/100));lcdprintPGM("00");
} }
if((activeline==line) ) if((activeline==line) )
@ -650,7 +677,7 @@ void MainMenu::showControl()
{ {
if(encoderpos<5) encoderpos=5; if(encoderpos<5) encoderpos=5;
if(encoderpos>990) encoderpos=990; if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcd.print("00"); lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcdprintPGM("00");
} }
} }
}break; }break;
@ -658,7 +685,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Vxy-jerk: "); lcd.setCursor(0,line);lcdprintPGM(" Vxy-jerk: ");
lcd.setCursor(13,line);lcd.print(itostr3(max_xy_jerk/60)); lcd.setCursor(13,line);lcd.print(itostr3(max_xy_jerk/60));
} }
@ -692,7 +719,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" PID-P: "); lcd.setCursor(0,line);lcdprintPGM(" PID-P: ");
lcd.setCursor(13,line);lcd.print(itostr4(Kp)); lcd.setCursor(13,line);lcd.print(itostr4(Kp));
} }
@ -726,7 +753,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" PID-I: "); lcd.setCursor(0,line);lcdprintPGM(" PID-I: ");
lcd.setCursor(13,line);lcd.print(ftostr51(Ki)); lcd.setCursor(13,line);lcd.print(ftostr51(Ki));
} }
@ -760,7 +787,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" PID-D: "); lcd.setCursor(0,line);lcdprintPGM(" PID-D: ");
lcd.setCursor(13,line);lcd.print(itostr4(Kd)); lcd.setCursor(13,line);lcd.print(itostr4(Kd));
} }
@ -797,7 +824,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" PID-C: "); lcd.setCursor(0,line);lcdprintPGM(" PID-C: ");
lcd.setCursor(13,line);lcd.print(itostr3(Kc)); lcd.setCursor(13,line);lcd.print(itostr3(Kc));
} }
@ -834,11 +861,11 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Vmax "); lcd.setCursor(0,line);lcdprintPGM(" Vmax ");
if(i==ItemC_vmaxx)lcd.print("x:"); if(i==ItemC_vmaxx)lcdprintPGM("x:");
if(i==ItemC_vmaxy)lcd.print("y:"); if(i==ItemC_vmaxy)lcdprintPGM("y:");
if(i==ItemC_vmaxz)lcd.print("z:"); if(i==ItemC_vmaxz)lcdprintPGM("z:");
if(i==ItemC_vmaxe)lcd.print("e:"); if(i==ItemC_vmaxe)lcdprintPGM("e:");
lcd.setCursor(13,line);lcd.print(itostr3(max_feedrate[i-ItemC_vmaxx]/60)); lcd.setCursor(13,line);lcd.print(itostr3(max_feedrate[i-ItemC_vmaxx]/60));
} }
@ -873,7 +900,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Vmin:"); lcd.setCursor(0,line);lcdprintPGM(" Vmin:");
lcd.setCursor(13,line);lcd.print(itostr3(minimumfeedrate/60)); lcd.setCursor(13,line);lcd.print(itostr3(minimumfeedrate/60));
} }
@ -907,7 +934,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" VTrav min:"); lcd.setCursor(0,line);lcdprintPGM(" VTrav min:");
lcd.setCursor(13,line);lcd.print(itostr3(mintravelfeedrate/60)); lcd.setCursor(13,line);lcd.print(itostr3(mintravelfeedrate/60));
} }
@ -945,12 +972,12 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Amax "); lcd.setCursor(0,line);lcdprintPGM(" Amax ");
if(i==ItemC_amaxx)lcd.print("x:"); if(i==ItemC_amaxx)lcdprintPGM("x:");
if(i==ItemC_amaxy)lcd.print("y:"); if(i==ItemC_amaxy)lcdprintPGM("y:");
if(i==ItemC_amaxz)lcd.print("z:"); if(i==ItemC_amaxz)lcdprintPGM("z:");
if(i==ItemC_amaxe)lcd.print("e:"); if(i==ItemC_amaxe)lcdprintPGM("e:");
lcd.setCursor(13,line);lcd.print(itostr3(max_acceleration_units_per_sq_second[i-ItemC_amaxx]/100));lcd.print("00"); lcd.setCursor(13,line);lcd.print(itostr3(max_acceleration_units_per_sq_second[i-ItemC_amaxx]/100));lcdprintPGM("00");
} }
if((activeline==line) ) if((activeline==line) )
@ -974,7 +1001,7 @@ void MainMenu::showControl()
{ {
if(encoderpos<1) encoderpos=1; if(encoderpos<1) encoderpos=1;
if(encoderpos>990) encoderpos=990; if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcd.print("00"); lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcdprintPGM("00");
} }
} }
}break; }break;
@ -982,8 +1009,8 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" A-retract:"); lcd.setCursor(0,line);lcdprintPGM(" A-retract:");
lcd.setCursor(13,line);lcd.print(ftostr3(retract_acceleration/100));lcd.print("00"); lcd.setCursor(13,line);lcd.print(ftostr3(retract_acceleration/100));lcdprintPGM("00");
} }
if((activeline==line) ) if((activeline==line) )
@ -1008,7 +1035,7 @@ void MainMenu::showControl()
{ {
if(encoderpos<10) encoderpos=10; if(encoderpos<10) encoderpos=10;
if(encoderpos>990) encoderpos=990; if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcd.print("00"); lcd.setCursor(13,line);lcd.print(itostr3(encoderpos));lcdprintPGM("00");
} }
} }
}break; }break;
@ -1016,7 +1043,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Esteps/mm:"); lcd.setCursor(0,line);lcdprintPGM(" Esteps/mm:");
lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[3])); lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[3]));
} }
@ -1053,7 +1080,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Store EPROM"); lcd.setCursor(0,line);lcdprintPGM(" Store EPROM");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -1067,7 +1094,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Load EPROM"); lcd.setCursor(0,line);lcdprintPGM(" Load EPROM");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -1081,7 +1108,7 @@ void MainMenu::showControl()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" Restore Failsafe"); lcd.setCursor(0,line);lcdprintPGM(" Restore Failsafe");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -1165,7 +1192,7 @@ void MainMenu::showSD()
{ {
if(force_lcd_update) if(force_lcd_update)
{ {
lcd.setCursor(0,line);lcd.print(" File"); lcd.setCursor(0,line);lcdprintPGM(" File");
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -1185,11 +1212,11 @@ void MainMenu::showSD()
if(true) if(true)
#endif #endif
{ {
lcd.print(" \004Refresh"); lcdprintPGM(" \004Refresh");
} }
else else
{ {
lcd.print(" \004Insert Card"); lcdprintPGM(" \004Insert Card");
} }
} }
@ -1210,7 +1237,7 @@ void MainMenu::showSD()
{ {
card.getfilename(i-2); card.getfilename(i-2);
//Serial.print("Filenr:");Serial.println(i-2); //Serial.print("Filenr:");Serial.println(i-2);
lcd.setCursor(0,line);lcd.print(" ");lcd.print(card.filename); lcd.setCursor(0,line);lcdprintPGM(" ");lcd.print(card.filename);
} }
if((activeline==line) && CLICKED) if((activeline==line) && CLICKED)
{ {
@ -1292,7 +1319,7 @@ void MainMenu::showMainMenu()
{ {
case ItemM_watch: case ItemM_watch:
{ {
if(force_lcd_update) {lcd.setCursor(0,line);lcd.print(" Watch \x7E");} if(force_lcd_update) {lcd.setCursor(0,line);lcdprintPGM(" Watch \x7E");}
if((activeline==line)&&CLICKED) if((activeline==line)&&CLICKED)
{ {
BLOCK; BLOCK;
@ -1302,7 +1329,7 @@ void MainMenu::showMainMenu()
} break; } break;
case ItemM_prepare: case ItemM_prepare:
{ {
if(force_lcd_update) {lcd.setCursor(0,line);lcd.print(" Prepare \x7E");} if(force_lcd_update) {lcd.setCursor(0,line);lcdprintPGM(" Prepare \x7E");}
if((activeline==line)&&CLICKED) if((activeline==line)&&CLICKED)
{ {
BLOCK; BLOCK;
@ -1313,7 +1340,7 @@ void MainMenu::showMainMenu()
case ItemM_control: case ItemM_control:
{ {
if(force_lcd_update) {lcd.setCursor(0,line);lcd.print(" Control \x7E");} if(force_lcd_update) {lcd.setCursor(0,line);lcdprintPGM(" Control \x7E");}
if((activeline==line)&&CLICKED) if((activeline==line)&&CLICKED)
{ {
BLOCK; BLOCK;
@ -1334,13 +1361,13 @@ void MainMenu::showMainMenu()
#endif #endif
{ {
if(card.sdprinting) if(card.sdprinting)
lcd.print(" Stop Print \x7E"); lcdprintPGM(" Stop Print \x7E");
else else
lcd.print(" Card Menu \x7E"); lcdprintPGM(" Card Menu \x7E");
} }
else else
{ {
lcd.print(" No Card"); lcdprintPGM(" No Card");
} }
} }
#ifdef CARDINSERTED #ifdef CARDINSERTED
@ -1356,7 +1383,8 @@ void MainMenu::showMainMenu()
}break; }break;
#endif #endif
default: default:
SERIAL_ERRORLN("Something is wrong in the MenuStructure."); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Something is wrong in the MenuStructure.");
break; break;
} }
} }

7
Marlin/watchdog.pde
Unescape View File

@ -41,10 +41,11 @@ ISR(WDT_vect)
{ {
#ifdef RESET_MANUAL #ifdef RESET_MANUAL
LCD_MESSAGE("Please Reset!"); LCD_MESSAGEPGM("Please Reset!");
SERIAL_ERRORLN("Something is wrong, please turn off the printer."); SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Something is wrong, please turn off the printer.");
#else #else
LCD_MESSAGE("Timeout, resetting!"); LCD_MESSAGEPGM("Timeout, resetting!");
#endif #endif
//disable watchdog, it will survife reboot. //disable watchdog, it will survife reboot.
WDTCSR |= (1<<WDCE) | (1<<WDE); WDTCSR |= (1<<WDCE) | (1<<WDE);

Write Preview
Loading…
Cancel
Save